| Resume alert | Resumes 31 - 40 of 198 |
Superintendent Manager
Scotts Valley, CA
... wind was active and providing service to patients. We had to perform a med gas shutdown and coordinate with the facility for the necessary tanks for patient use. Part of the project was to install new exhaust unit by crane up to the roof and build a ... - 2020 Nov 16
... wind was active and providing service to patients. We had to perform a med gas shutdown and coordinate with the facility for the necessary tanks for patient use. Part of the project was to install new exhaust unit by crane up to the roof and build a ... - 2020 Nov 16
Assistant Engineer
Fremont, CA
... • Fortran-based solver development with lattice Boltzmann’s method for two-phase flows • Lab experimentalist at Supersonic Wind Tunnel at Rutgers University Software and Programming Skills: Simulation and Analysis: ANSYS CFX, ANSYS fluent, GASPex, ... - 2020 Oct 23
... • Fortran-based solver development with lattice Boltzmann’s method for two-phase flows • Lab experimentalist at Supersonic Wind Tunnel at Rutgers University Software and Programming Skills: Simulation and Analysis: ANSYS CFX, ANSYS fluent, GASPex, ... - 2020 Oct 23
Principle System Enginner
San Jose, CA
... Development Environment C, NGXR (Embedded Linux [Wind River Linux2.6]), Firmware/Driver, Multicore/SoC/ASICs/FPGA, Embedded Networking Architecture. Roles & Responsibilities Involved proposal writing and estimations, requirement gathering, SFS, ... - 2020 Sep 22
... Development Environment C, NGXR (Embedded Linux [Wind River Linux2.6]), Firmware/Driver, Multicore/SoC/ASICs/FPGA, Embedded Networking Architecture. Roles & Responsibilities Involved proposal writing and estimations, requirement gathering, SFS, ... - 2020 Sep 22
Mechanical Engineer
Milpitas, CA
... Molex - Fremont, CA Mar 2018 – May 2018 Mechanical Test Engineer • Formulated statistical data reduction of thermal lab experiments carried out with wind-tunnel to test analyze hardware and system feasibility, design, operation and performance. • ... - 2020 Aug 09
... Molex - Fremont, CA Mar 2018 – May 2018 Mechanical Test Engineer • Formulated statistical data reduction of thermal lab experiments carried out with wind-tunnel to test analyze hardware and system feasibility, design, operation and performance. • ... - 2020 Aug 09
Mechanical Engineer
San Jose, CA
... Wind Turbine 2018 • Fabricated the lightest turbine base design by using low-density balsa wood. • 3D printed turbine blades designed in SolidWorks and achieved highest power generated by using a creative curved-edge plastic part design. Arduino ... - 2020 Jul 20
... Wind Turbine 2018 • Fabricated the lightest turbine base design by using low-density balsa wood. • 3D printed turbine blades designed in SolidWorks and achieved highest power generated by using a creative curved-edge plastic part design. Arduino ... - 2020 Jul 20
Spring 2020 Mechanical Engineer Graduate
San Jose, CA
... • Used wind tunnel testing to determine uplift force to establish padded standoff ballast weight and mounting point loads versus roof pitch. Heat Sink Optimization, Thermal System Design Project Fall 2019 • Worked in a team of 4 to optimize the ... - 2020 Jun 30
... • Used wind tunnel testing to determine uplift force to establish padded standoff ballast weight and mounting point loads versus roof pitch. Heat Sink Optimization, Thermal System Design Project Fall 2019 • Worked in a team of 4 to optimize the ... - 2020 Jun 30
Engineer Engineering
Milpitas, CA
... Vertical Axis Wind Mill • Designed and Manufactured a prototype of Vertical Axis Wind Mill. • Structural and Thermal analysis upon varying load was conducted to obtain a more efficient design and improve mechanical efficiency by 6%. CERTIFICATIONS ... - 2020 Jun 29
... Vertical Axis Wind Mill • Designed and Manufactured a prototype of Vertical Axis Wind Mill. • Structural and Thermal analysis upon varying load was conducted to obtain a more efficient design and improve mechanical efficiency by 6%. CERTIFICATIONS ... - 2020 Jun 29
Aerospace Engineer
San Jose, CA
... Gas Dynamics, Fluid Mechanics, Problem Solving, Technical Writing, Thermodynamics, Propulsion, Mission Design Laboratory Skills: Wind Tunnel Testing, Computer Repair, Soldering EXPERIENCE Research Assistant San Jose State University Oct. ... - 2020 Jun 27
... Gas Dynamics, Fluid Mechanics, Problem Solving, Technical Writing, Thermodynamics, Propulsion, Mission Design Laboratory Skills: Wind Tunnel Testing, Computer Repair, Soldering EXPERIENCE Research Assistant San Jose State University Oct. ... - 2020 Jun 27
Sap Engineer
San Jose, CA
... The network consists of 5 Geographical locations (Distribution Centers) where demand is entered for Wind Turbines in Demand Planning Book. The Demand is percolated to the entire network Plants by means of SNP (Heuristics) Run. Have worked in 3 ... - 2020 Jun 09
... The network consists of 5 Geographical locations (Distribution Centers) where demand is entered for Wind Turbines in Demand Planning Book. The Demand is percolated to the entire network Plants by means of SNP (Heuristics) Run. Have worked in 3 ... - 2020 Jun 09
Computer Engineer
Dublin, CA
... UltraCell LLC Intern, June 2017 – August 2017 • Built a wind tunnel and prototyped fuel cell designs in collaboration with a team of engineers • Designed and implemented process improvements to expedite manufacturing. Modified CNC routing machine to ... - 2020 May 01
... UltraCell LLC Intern, June 2017 – August 2017 • Built a wind tunnel and prototyped fuel cell designs in collaboration with a team of engineers • Designed and implemented process improvements to expedite manufacturing. Modified CNC routing machine to ... - 2020 May 01