E & I

SANDRA REN

*** ********* ***** **, *******, Alberta T2X 3X1

403-***-**** ● ******.**.***@*******.***

OBJECTIVE A position in Electrical, Control Systems Engineer/Technologist

PROFILE OR SUMMARY

Bachelor's Degree in Instrumentation engineering, eligible for registration with APEGGA.

Over 10 years experience in control systems design and start-up, Knowledge of PLC programming & HMI configuration, Profibus, Modubus, DeviceNet, ControlNet, DH+, Enthernet communication, MCCs, VFDs, also skilled in the use of MS-Office & AutoCAD.

EMPLOYMENT EXPERIENCE

Control Systems Designer 09/2007~12/2008

Jacobs

Calgary, AB

3D modeling & 2D instrument layout, JB/Marshalling wiring diagram, loop diagram, installation details drawing package design.

Project

Suncor Sulphur Recovery

E & I Designer 09/2006~09/2007

TG Engineering Inc.

Calgary, AB

Design drawings, including Cable Tray & Grounding Layout, Electrical Site Plot Plan, Hazardous Area Classification, Cable Schedule, Bill of Material, MCC Building Electrical Layout, Single Line Diagram, Lighting Panel Schedule, PLC Panel Layout, Power Distribution, PLC(Controllogix) I/O Schematics, Motor Control Schematics(Square D MCC), and Electrical Connection Details.

Projects

NewAlta Brooks waste processing facility upgrade

EnCana Bantry compressor stations

Conocophillips Niton compressor stations

Conocophillips Ghost Pine compressor stations

Control Systems Designer 06/2005~09/2006

Combustion Solutions Inc.

Calgary, AB

Design and test BMS (Burner management system) and CCS (Combustion control system), using PLC (S7-300, Compactlogix，Controllogix), Fireye, Yokogawa controllers and field instruments.

Projects for: Alberta Processor, Calgary Airport, Husky, Imperial Oil, Mosaic, Richardson International Ltd, Irving Oil, National Iranian Gas Plant…

Process Control Engineer / Designer 07/1988~05/2004

Automation Department

Luoyang Engineering and Research Institute for Nonferrous Metals Processing, China

• Designed and set-up PLC based control systems(use AB,SIEMENS,OMRON products S7-200, S7-300 and S7-400, SLC500,C200H, C60)

• Designed and set-up AC/DC motor control systems (use ABB ,AB products DCS500/600, ACS800/600/400, Powerflex 70/700 for speed & torque control).

• Developed the side guiding system, applying knowledge of optics, electricity, electronics, and hydraulics.

• Developed tension control system, it is computer based system for high speed winding equipment, designed interface circuit DI/DO, AI/AO, PI, programmed the application software.

• Designed layout and schematic drawing, for compressors, boilers and pump stations

• Supervised & inspected the onsite installation, responsible for the testing, tuning, adjusting.

• Provided technical training to the maintenance electrician, provided additional technical support after commissioning, assisted in the continuous improvement process for the equipment.

• Prepared material cost and timing estimates, reports.

• Designed specifications, developed maintenance and operating standards for automation equipments.

The projects

1. 1450mm Reversing Cold Steel Strip Rolling Mill 01/2004~05/2004 Zhaoqing, Guangdong Province

2. 1830mm Aluminum Strip Continuous caster 10/2003~12/2003 Xin’an, Henan Province

3. 1450mm Wide Aluminum Strip Tension Lever 03/2002~02/2003 Wuxi, Jiangsu Province

4. 1300mm Hot Aluminum Rolling Mill 08/2001~01/2002 Xiezhou, Shanxi Province

5. 1400mm Aluminum Foil Rolling Mill 03/2001~11/2001 Changshu,Jiangsu Province

6. Jincheng Central Heating Project 07/2000--10/2000 Jincheng, Shanxi Province

7. 560mm Copper Strip double-surface Milling Line 05/1999~02/2000 Heze, Shandong Province

8. Aiding Equipment of 1800KN Extrusion Press 03/1999~06/1999 Wuxi, Jiangsu Province

9. 1050mm Steel Strip Coating Line 05/1996~12/1998 Hengshui Hebei Province

10. 1400mm Aluminum Strip slitting and Cut to Length Line 08/1996~01/1997 Xuzhou, Jiangsu Province

EDUCATION AND TRAINING

Autoplant Training, 2007

Simatic Safety PLC Integration Training, 2005

PLC Application Certificate, 1995

AC/DC Motor Control Theory Training, 1990

Bachelor of Engineering 1988

Measurement Technology & Instrument

Huazhong University of Science and Technology

Others: MS-Office/ AutoCAD/Procad/Microstation/Autoplant/ Protel/ RSLogix 5000/ RSView/Panelbuilder/ Step7/ Protool/ Wincc/ Drivewindow

REFERENCES

Available upon request

Contact this candidate