Engineer Quality Control
Resume:
ALI KHOSROWZADEH
Canada
phone: 416-***-****
********@*****.***
CAREER SUMMARY
Solutions-focused and highly knowledgeable drilling engineering professional with 10+ years of experience in off-shore and on-shore drilling operations. Combines advanced expertise in drilling fluid systems with a strong practical experience in all facets of drilling onshore and offshore operations. Takes the initiative to investigate and resolve complex field issues. Proven work an extensive record of successes identifying process, training and technology improvements, which deliver measurable results in cost control, environmental protection, risk mitigation and well production.
SKILLS
Extensive knowledge of office work related software including MS Office, Well view & Rig view Proven to work Accumap Drilling Office, Landmark and Drilling office software
Well integrity and QHSE management skills Rig Operations Streamlining & Optimization
Drilling Procurement life cycle analysis Deep Vertical and horizontal drilling & Geosteering systems
Well Planning, Casing Design, bit selection, and Drilling Optimization Cost Effective Negotiation Strategy of Operation
Drilling fluid design and Drilling fluid parameters optimization Core Hole Drilling
PROFESSIONAL EXPERIENCE
HUSKY ENERGY, DRILLING WEST 2007 - Present
Drilling Engineer
Key Responsibilities
• Prepared well benchmarking for Rainbow Lake, Ferrier areas
• Designed BHA, drilling parameters and casing design for deep vertical and horizontal wells
• Acquired experience on well drilling daily reports with recommendation for drilling optimization of Brazeue (critical sour gas), Lynx HZ, Ricinus (critical sour gas) and Wildhorse area wells (exploration and development wells)
• Planned drilling program for deep exploration well in Moose area
• Prepared external benchmarking for Lynx area horizontal wells
• Optimized bit selection for deep wells and prepared AFE for Lynx horizontal wells
Key Accomplishments
• Planned well program for two deep gas horizontal wells in Lynx area, lateral length up to 900m
• Reviewed well program for deep vertical critical sour gas exploration well, 4400 m, in Ricinus area
• Reduced drilling cost for surface hole drilling by $ 60K per well by using optimized BHA design and using Smith’s VertiDrill PDC bits
• Improved ROP 30% in Lynx deep horizontal wells by optimizing drilling fluid parameters and BHA
Schlumberger (PEDCO - IPM JV) 2004 - 2006
Drilling Quality Control Engineer
Key Accomplishments
• Supervised well drilling integrity management for Oil /Gas field Drilling Off/Onshore Projects.
• Reduced Drilling EPC project from 40% to 15% during 18 months.
• Reviewed and revised cost estimation for more than 55 horizontal and multilateral wells. (Wellhead pressure rating from 1200 to 5000 PSI).
• Member of drilling engineering team for well planning and well design of 55 horizontal and multilateral wells using Schlumberger’s Drilling Office software.
• Assisted drilling team to achieve a record of 600 meters/day in deep horizontal drilling (sliding and drilling modes) with Schlumberger’s Power Drive motor and Reed’s Trex PDC bit.
• Selected jack up rigs for offshore drilling operation
ALI KHOSROWZADEH Page 2
• Supervised and utilized different QHSE system features such as: ERP (Emergency Response Plan), drilling QHSE RWP (Remedial Work Plan), SQM (Service Quality Meetings) and PMS (Preventive Maintenance System)
• Effectively managed drilling services contracts regarding Key Factors and quality requirements
Schlumberger (PEDCO - IPM JV) 2000-2004
Drilling Engineer
• Member of well planning & design team for development of low production oil and gas fields. Designed 100 re-entry, horizontal and multilateral wells (sour and sweet) and increased production rate of approximately 200,000 bbl/day
• Proposed, investigated and reviewed Drill Bit Selection for different drilling operation requirements.
• Determined and coordinated appropriate well completion techniques; used and worked with Baker’s Monobore completion system, Smith’s liner hangers and packers, Halliburton and Schlumberger’s down hole equipment.
• Assessed costs and evaluated the economic viability of potential drilling locations (AFE, cost estimation and cost analyses).
• Implemented Drilling trouble shooting during rig spot, drilling operation, logging, and well testing, well flowing and well hand over to production dept.
• Member of wellhead and completion design team for about 100 gas and oil wells (sour and sweet).
• Structured and implement health, safety and environmental controls on drilling operations.
• Improvised, performed, and actively monitored the whole drilling procurement process regarding engineering and quality assurance requirements.
• Used Schlumberger’s Shell 2000 system to manage contractors and drilling operation quality
NIDC 1991-2000
Engineer
• Mud logger(1995-2000), drilling rotary equipment quality control engineer(1992-1995), assistant driller (1991-1992)
EDUCATIONAL ACHIEVEMENTS
Bachelor of Auto/Diesel Engines Degree 1983 - 1987
B.Sc. in Chemical Engineering, Major: Gas Industry 1987 - 1991
Reed Drilling Bit Design and Bit Selection 2005
SAIT Petroleum upstream certificate 2007-2008
PROFESSIONAL DEVELOPMENT
Drilling Engineering Certificate 1999
Drilling Office, Schlumberger, Calgary 2002
HQSE Management System, Shell, Calgary 2004
Reed Drilling Bit Design and Bit Selection 2005
H2S Alive Certificate + CPR with Enform 2007
OpWorks Supervisor Certificate 2007
Second line well control & SARA with Enform 2008
Halliburton Mud School 2008
AFFILIATION
Membership to Association of Professional Engineers, Geologists, and Geophysicists of Alberta (APEGGA) under process
Member of SPE
Contact this candidate