Industrial Machine Operator and Assembler
Resume:
CHRIS GRIDER
****************@*****.***
Camden AR 71701
OBJECTIVES
To better myself by learning more about different things and new employment opportunities wherever that may lead
EDUCATION
Southern Arkansas University
May 02 2013
Associate of Industrial Technology
Member of the National technical Honor Society
OSHA 40 hour safety card
Forklift Training
Summit Lathe
Autoclave Pressuring System
Customer service
Computers
Water
Wastewater
Heavy machinery
Pest Control
Experience
L3Harris/Aerojet Rocketdyne
02/28/19- present
Autoclave operator
Lathe Operator
Was responsible for Temperature,Vacuum,and pressure of two machines at the same time
Duties included driving tugger loading and unloading rail table top carts with rocket motor cases and parts
Performed many cooks by myself
Trained many people
Ran a Summit Lathe cutting insulators that had to be a certain specification
Duties included loading and unloading mandrels with a hoist
Using a PI tape
DE tooling them after milling them
Preparing them for the next operation
LOCKHEED MARTIN
10/30/17-02/08/18
Assembler
Drill holes, Rivet, hi-locks, counter sink, counter bore air craft parts c130.
Used different types of sealants, and compounds following written, and electronic work instructions.
Used air drills, shavers, jigs, rivet squeezers, rivet fans, and called out fixtures to complete jobs.
Worked on paint –process line preparing air craft parts for painters sanding, polishing, taping parts so they don’t move on racks. Putting them on serialized racks, always keeping kits together
Several kits at once were worked, and documented. Finish prep work of painted parts. Put in proper place to be shipped, and accounted for. Safety training
Supervisor: Jason Buchannon Phone: 727-***-****
Aerojet Rocketdyne
Assembler 3
02/17/17– 10/13/17
Ran a Lathe remotely to cut propellant out of many different kinds of rocket motors.
Ran a washout diesel engine to clean out motor cases that had been fired or propellant removed, and Bagged all explosive accordingly
Transported all cleaned cases to said locations around the plant.
SKILLS
Machined and hand tools
Computers
Used a crane to load and unload motor cases
Critical parts
Serialization
Packing, uncrating, shipping, and transporting
Supervisor:
Randy Wilson
LOCKHEED MARTIN
Assembler Spec
2014/2017
Pac-3 missile
Refurbished all canisters so they could be resold and reused in the field. This included grinding, polishing, and reconditioning parts. Loading canisters on a roll-over machine with crane.
Painted and stenciled the Pac-3 canister complicated camouflage patterns blending colors to pass DCMA inspection. Mixed and applied all paints and sealants. Kept track of all paper work and serial numbers after electrical test were performed. Used crane to weigh, and move canisters
Put together and reconditioned critical parts for sub- assembly which included: riveting,drilling,torqueing,deburring.
All confirmations were recorded in SAP.
Working with hand drills, setting torque wrenches, using programs on pc to check electrical resistance
Crane proficiency, uses of many different chemicals, and preparing the canisters and smaller parts for shipping.
Recording everything in SAP
Supervisor : Clark Lewis
870-***-**** (3015)
Lockheed Martin
2006/2014
GMLRS/MLRS
Built and assembled the MLRS rocket, used a spin down machine and, a weigh table to calculate sabot angles
Built the spinning tail for the Guided Multiple Rocket systems duties included: preparing the bearing, adjusting tabs for the spring-locking mechanisms (fins). Keeping track of all measurements to make sure spring tension and height adjustment fell within tolerance. Serializing after completion
Applied skins to the warheads for the GMLRS with adhesive and torqueing screws to specifications
Loaded the GMLRS rocket into a pod using serialized positions and torqueing applications
All measurements and serial numbers were recorded electronically in SAP. Drove tugs to move pods in and out.
Skills: using calipers, fluke gage, and feeler gages, and torque wrenches. Inking and serializing the parts, and safety wire.
Supervisor: Kyle Taylor
Lockheed Martin
2003/2006
MLRS
Built vehicles and applied top armor to cages.
Moved top armor, green beams, gold beams, and cages with a crane.
Drilled all the holes with drill jigs, and pneumatic drills for the top armor, and reamed them out, and counter bored, or spot faced all the holes for riveting applications.
Prepared the green and gold beams for installation using a hand drill and counter boring holes.
Using a crane effectively, operating and locating pneumatic drills, and proficiently locating beams and top armor to cage.
Supervisor: Ray Gavin 870-***-****
Lockheed Martin
2000/2003
Remanufacture
Tear down all the MLRS cages coming back in from the field for reconditioning
Duties included: Running a CNC machine cutting flanges off old bearings and housings, using a press to push out old bearings and push in new ones. Large and small parts were conditioned this way after these parts were sand-blasted, and cleaned to be repainted.
Removed all parts large and small using many different tools. Parts were then placed on serialized racks. New heli-coil inserts, bushings, and hardware were then outfitted to these parts. All confirmations was done in SAP
Supervisor: Ray Gavin 870-***-****
Shumaker Water Company
1995/2000
(Water and wastewater)
Put in new water lines, read water meters, and repaired existing lines.
Packed bell joints, ran trac-hoe backhoe, and my own route for water meters.
Worked wastewater plant fixing leaks, replacing pumps, and cleaning sludge screens.
Took samples of wastewater, and repaired broken lines. Worked on lift stations.
1993/1995
Small engine repair
Technical degree fixing and repairing small engines, Lawnmowers, weed eaters,chainsaws,edgers, some outboard 2 cycle experience. Diagnose and repair. Worked with fuel systems, and some electrical systems.
1986/1991
Esco Termite & Pest Control
Had an Arkansas Pest Control and Termite license
Ran my own route Pest. Done all crawls for termite work and water damage. Sprayed herbicide for the Corp of Engineers. Treated slabs. Done several pre treats trench around blocks. Help with dig outs.
Contact this candidate