Electrical & Instrumentation Engineer (Oil & Gas)

Location:

Batam, Riau Islands, Indonesia

Salary:

Negotiable

Posted:

July 11, 2026

Contact this candidate

Resume:

The Summer Residence Block C*/** Batam Kota – Batam Centre, Batam, Kepri – Indonesia. 29464

Phone: +62-813*-****-***, +62-812*-****-*** (Indonesian Mobile), E-mail Address: ********.******@*****.*** MARTHIN HENRY HUTAGAOL. B.Eng

Career summary

More than Eighteen years extensive experienced in field Engineering, Supervision, Inspection, Ex Inspection in Fabrication, Construction, Installation, Calibration, and Commissioning of Electrical and Instrument of Onshore & Offshore in various Oil and Gas platform such as: Well Head Platform, Floating Production Unit (FPU), LNG Condensate Exporting, Installation Subsea Cable (Cable Lay), Gas Compressor Platform, Over Land Conveyor, Ship Drilling, E-House Electric at FPSO (Floating Process & Storage Offloading), Platform Utility Module, Platform Living Quarter Module, Central Process Platform (CPP), Jack Up Drilling Rig and Service Jack Up Accommodation also Vessel Supply Boat . I am well known as a team player and have never left a project under bad conditions Construction project present many challenges and it gives a good sense of achievement and job satisfaction to have been a part of team that gets the job done. And also having experience and many time to do perform FAT / IFAT as per project specification. Understanding of review, the related instrumentation drawing such as piping and Instrumentation Diagram (P & ID), Cause & Effect Diagram, Loop Drawing, Tubing Data & Pressure required, Operational Sequence or Removing Orifice, Data Sheet, Type Fitting and selection material as required, ITR’s approval, punch list clearance, SBUM (Standard Basic Unit Man hours), Industry Code & Standard.

EDUCATION

ENGINEERING DEGREE for ELECTRICAL ENGINEER (2000 – 2008) SCHOOL for ENGINEERING of PLN’S FOUNDATION (STT - PLN) – JAKARTA – INDONESIA TRAININGS

1. Electrical & Instrument in Hazardous Area (COMP-EX) on September 2023 by JTLimited. Certificate Number 80415268. 2. Electrical Instrument in Hazardous Area (EEHA – AS/NZS 4671) on December 2022 by Tech Skill Australia – TSA. Certificate Number CoA 2022/EEHA0312.

3. Lead Auditor IRCA ISO 9001-2015 on April 2022 by Fore Front – UK. 4. Electrical & Instrument in Hazardous Area (COMP-EX) on August 2017 by JTLimited. Certificate Number 61389 5. Electrical Instrument Equipment’s in Hazardous Area (ATEX EEHA) on July 2014 by City and Guilds of London Institute – OPITO. Certificate Number 240914/0666-05/076221/HLS74601/M/23/03/79. 6. FOET + TSbB on February 2021 by WOOD Group Training Approved by OPITO. 7. Electrical & Instrument Inspector on October 2008 by Universal Institute for NDT & Welding Inspection – Batam. Language:

Good in English and Fluent in Indonesia

Employment History :

Qatar Energy LNG (QELNG) June 2023 – May 2025

Comp-Ex Certified EIT Supervisor Construction,

Client Reps for North Field Expansion (NFXP) Offshore Project, on McDermott – Batam Fabrication Yard. Job Summary :

Supervise and oversee Electrical Instrument and Telecom during installation stage of each wellhead platform to ensure objectives are safely met within the approved scope and schedule. Ensuring execute work compliance with reference standard, policies, approved procedure & specification. Supervise and oversee quality output & schedule with compliance to safety rules and regulations.

1. Review Inspection Test Plan (ITP), Project Specification, Method Statement, etc. according to (Electrical, Instrument, Telecom design basis) Company Requirements and International Code Standard (IEC, NEMA, etc.). 2. Review and comments on detail schedule of Electrical Instrument Telecom (EIT) works. 3. Auditing document Contractor & Sub-Contractors personnel in charge (Supervisor, Foreman and Technician) comply with Company Requirements, ITP and Procedure Approved.

4. Witness during Perform Material E&I receiving, and detail Cable tray/ladder, switchgear, Transformer, MCC panel, Junction Boxes any types, Transmitter (Pressure, Temperature, Level, Flow and Orifice) Control Valve, Packages Equipment (High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Integrated Control and Safety System (ICSS), Distributed Control System (DCS), Fire & Gas System, Instrumented Protective System

(IPS), Motors, cable any types, Lighting Fixtures, Telecom System, UPS and Battery Charger Systems based on ITR by Contractor.

5. Supervise and oversee execution installation of all electrical, Instrument & Telecom works (supports, equipment’s and accessories) are complying with ITP, the latest AFC drawings, Project Specifications, International Code Standard (IEC, NEMA, etc.) manufacturer instruction, safety rule, and good practice. 6. Coordinate with all disciplines (Structural, Mechanical, Piping and Safety) to guarantee the prompt, safe and environmentally respectful execution of all Electrical Instrument Telecom (EIT) Installation activities. And assist construction activities with EIT contractor to insure meets schedule. And enforce HSE plan & quality procedures. 7. Coordinate and interface with cross-functional teams (Mechanical, Piping, Contractor, Sub-Contractors, Company) to evaluate the success and effectiveness to achieve KPI (Key Performance Indicator) and align project goals. 8. Walkthroughs with Contractor, Sub-Contractor and disciplines involved, in accordance with systems completion priorities, in order to determine the required actions to be completed to achieve the mechanical completion. 9. Meetings coordination in a perspective of an overall optimization, in terms of system completion or alternative solutions to mitigate the inconveniences that might occur.

The Summer Residence Block C1/06 Batam Kota – Batam Centre, Batam, Kepri – Indonesia. 29464 Phone: +62-813*-****-***, +62-812*-****-*** (Indonesian Mobile), E-mail Address: ********.******@*****.*** 10. Diagnose and resolve issues any finding on site based on Sub-System Priority (LV systems, MV System, Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, UPS and Battery Charger Systems, High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Integrated Control and Safety System (ICSS), Distributed Control System (DCS), Fire & Gas System, Instrumented Protective System (IPS), CCTV System, Navigation Aids & Foghorn System, Radio & Telecom System etc). 11. Perform Construction Surveillance Program (CSP) activities with the project quality plan & surveillance plan. 12. Witness Cable Test Optical Time Domain Reflectometer (OTDR) for cable Telecom / Fiber Optic, Time Domain Reflectometer, Insulation Test, and grounding test. Record of all relevant activities and outstanding works. 13. Coordinating and supervising the installation activities of the Electrical, Instrument Telecom (EIT) plans and ensures the safe operation on all EIT equipment’s once handed over to Commissioning (HV and LV Networks, Transformers, Switchgear, Protection Relays, Electrical Switching, LV & MV Motors and Motor Starters, UPS and Battery Charger Systems, Variable Frequency Drives/Soft Starters, Electrical Actuators, Pedestal Cranes and Hoists, Grounding Systems, Lighting and Small Power System, High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel (WHCP), Hydraulic Power Unit

(HPU), Integrated Control and Safety System (ICSS), Distributed Control System (DCS), Fire & Gas System, Instrumented Protective System (IPS), CCTV System, Navigation Aids & Foghorn System, Radio & Telecom System etc). 14. Supervise and oversee all Ex equipment’s and accessories installed comply with Hazardous Area Drawing (HAD) approved, ITP Approved, Manufacturer Instruction and International Code Standard (IEC 600079-14) 15. Control and updated of day to day activities closure Punch-List, coordinating with the Contractor and discuss on the outstanding activities during the weekly progress. 16. Prepared daily, report to Lead EIT Construction. QATARGAS September 2021 – March 2023

Comp-Ex Certified Senior E&I Inspector Client Reps for North Field Production Sustainability Investment 1, Project 1 (NFPS I1P1 – Project) on McDermott – Batam Fabrication Yard. Job Summary :

Coordinate the achievement of the plant process and utilities systems completion as defined in the project plans and schedules, in order to hand-over the systems to commissioning Team, coordinating all construction disciplines according to the established time frame and priorities and interfacing with Company, Contractor, Sub-Contractors, and Suppliers. 1. Review Inspection Test Plan (ITP), Project Specification, Method Statement, etc. according to (Electrical, Instrument, Telecom design basis) Company Requirements and International Code Standard (IEC, NEMA, etc.). 2. Auditing document Contractor & Sub-Contractors personnel in charge (Supervisor, Foreman and Technician) comply with Company Requirements, ITP and Procedure Approved.

3. Witness during Perform Material E&I receiving, and detail Cable tray/ladder, switchgear, Transformer, MCC panel, Junction Boxes any types, Transmitter (Pressure, Temperature, Level, Flow and Orifice) Control Valve, Packages Equipment (High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Integrated Control and Safety System (ICSS), Distributed Control System (DCS), Fire & Gas System, Instrumented Protective System

(IPS), Motors, cable any types, Lighting Fixtures, Navigation Aids System, Radio & Telecom System, UPS and Battery Charger Systems, etc based on ITR by Contractor.

4. Review document’s material receiving certificates for compliance to code and project spec. Review contractor, vendor and supplier’s completion files for accuracy and completeness. Check procedure of equipment test obtain the relevant document and manage documents certifying test.

5. Coordinate and interface with cross-functional teams (Mechanical, Piping, Contractor, Sub-Contractors, Company) to evaluate the success and effectiveness to achieve KPI (Key Performance Indicator) and align project goals. 6. Walkthroughs with Contractor, Sub-Contractor and disciplines involved, in accordance with systems completion priorities, in order to determine the required actions to be completed to achieve the mechanical completion. 7. Ensure that, quality installation of all electrical equipment and accessories are complying with ITP, the latest project drawings, specifications, manufacturer instruction, International Code Standard (IEC, NEMA, etc), safety rule, and good practice.

8. Perform and hold point for Ex inspection to all Ex equipment’s and accessories installed (Electrical Switching, LV & MV Motors and Motor Starters, UPS and Battery Charger Systems, Electrical Actuators, Pedestal Cranes and Hoists, Grounding Systems, Lighting and Small Power System, High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel

(WHCP), Hydraulic Power Unit (HPU), Fire & Gas System, CCTV System, Navigation Aids System, Radio & Telecom System) comply with Hazardous Area Drawing (HAD) approved, ITP Approved, Manufacturer Instruction and International Code Standard (IEC 600079-14)

9. Perform quality surveillance activities with the project quality plan & surveillance plan. Perform Flash Inspection Report

(FIR) when any finding during Surveillance inspection and RFI. 10. Witness Cable Test Optical Time Domain Reflectometer (OTDR) for cable Telecom / Fiber Optic, Time Domain Reflectometer, Insulation Test, and grounding test. Record of all relevant inspection activities and outstanding works. 11. Diagnose and resolve issues any finding on site based on Sub-System Priority (LV systems, MV System, Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, UPS and Battery Charger Systems, High Integrity Pressure Protection System (HIPPS), Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Integrated Control and Safety System (ICSS), Distributed Control System (DCS), Fire & Gas System, Instrumented Protective System (IPS), CCTV System, Navigation Aids System, Radio & Telecom System etc). 12. Update of day to day activities to push closure Punch-List, coordinating with the Contractor/Sub-Contractor and discuss on the outstanding Punch-List.

13. Witness final inspection for compliance and completeness prior to any equipment test. 14. Monitoring E & I construction & Installation activity, Witness Punch List Clearance. 15. Prepared daily, weekly, monthly report to Lead Quality. Global Proserv Indonesia April 2021 – May 2021

Ex Inspector Third Party for Apexindo Pratama Duta. Perform Surveillance and Audit Ex Inspection for TASHA New Generation Jack-up Rig, IMO 9682629 – Register Panama, MODU Class ABS

Verify the installation and compliance of explosion-proof electrical equipment’s, wiring and instrumentation. Inspect materials used in explosive environments to ensure they are suitable for use in hazardous areas according to industry safety standards

(e.g., ATEX, IECEx, NEC), project specifications and regulatory requirements. 1. Computerize Management Maintenance System (CMMS) for Ex Equipment. 2. Periodic Ex Inspection as per IEC 600079-17.

3. Ensure that, quality installation of all Ex equipment and accessories (Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Fire & Gas System, CCTV System, Telecom System etc) are complying with the latest project drawings, specifications, manufacturer instruction, safety role, and good practice.

4. Site surveillance to check and give comments if any finding, according to standard (hook up, P & ID drawing, etc. 5. Completeness of the documentation that has not been issued by the vendors: Ex Registers, Ex Check Sheets. 6. Updating Ex Register for databased as per actual equipment where installed in Hazardous Areas. 7. Ex final inspection as carry over on site.

Bureau Veritas Indonesia January 2021 – September 2021 Ex Inspector Third Party for Premier Oil Natuna Sea BV. Perform Surveillance and Audit Ex Inspection Gajah Baru CPP and LQ Platform, Gajah Baru Wellhead Platform, Naga Platform

& Pelikan Platform.

Job Summary :

(e.g., ATEX, IECEx, NEC), project specifications and regulatory requirements. 1. Periodic Ex Inspection as per IEC 600079-17

2. Coordinate and organizing the inspection activities installation of Ex equipment items. 3. Ensure that, quality installation of all Ex-equipment and accessories (Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Fire & Gas System, CCTV System, Telecom System etc) are complying with the latest project drawings, specifications, manufacturer instruction, safety rule, and good practice.

4. Site surveillance to check and give comments if any finding, according to standard (hook up, P & ID drawing, etc. 5. Completeness of the documentation that has not been issued by the vendors: Ex Registers, Ex Check Sheets. 6. Review of the Ex-Registers, Ex Check Sheets, Ex Certificates, all documentation to be countersign need on a randomized basis.

7. Ex final inspection as carry over on site.

Surveyor Indonesia December 2019 – November 2020

Ex Inspector Third Party for Premier Oil Natuna Sea BV. Periodic Ex Inspection for Anoa FPSO, Anoa Platform, AGX Platform, West Lobe Platform, Gajah Baru CPP and LQ Platform. Job Summary :

(e.g., ATEX, IECEx, NEC), project specifications and regulatory requirements. 1. Compering equipments JIS 1989 installed with Ex installation on Anoa FPSO, Anoa Platform and West Lobe Platform. 2. Coordinate and organizing the inspection activities installation of electrical and instrument items. 3. Ensure that, quality installation of all Ex-equipment and accessories (Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Fire & Gas System, CCTV System, Telecom System etc) are complying with the latest project drawings, specifications, manufacturer instruction, safety rule, and good practice.

4. Site surveillance to check and give comments if any finding, according to standard (hook up, P & ID drawing, etc. 5. Completeness of the documentation that has not been issued by the vendors: Ex Registers, Ex Check Sheets. 6. Review of the Ex Registers, Ex Check Sheets, Ex Certificates, all documentation to be countersign need on a randomized basis.

7. Ex final inspection as carry over on site.

Bechtel Oversea Corporation November 2017 – June 2019 CompEx certified E&I Inspector, working on BP West Nile Delta, Alexandria - Egypt. Job Summary :

Responsible for all construction activities within explosive environments (classified areas) of the Brownfield Refinery are conducted according to industry safety standards (e.g., ATEX, IECEx, NEC), project specifications and regulatory requirements. Verify the installation and compliance of explosion-proof electrical equipment, wiring and instrumentation. Inspect materials used in explosive environments to ensure they are suitable for use in hazardous areas. 1. Coordinate and organizing the daily inspection activities on Ex equipment receiving and installation. 2. Inspect and assess all hazardous area zones during the construction phase to ensure that appropriate classifications, protective measures and equipment are installed in compliance with safety standards for explosive environments. 3. Oversee construction activities in explosive atmosphere zones to ensure compliance with the necessary explosion protection, protocols, including the use of flameproof enclosures, intrinsically safe equipment and other safety mechanisms. Ensure The Summer Residence Block C1/06 Batam Kota – Batam Centre, Batam, Kepri – Indonesia. 29464 Phone: +62-813*-****-***, +62-812*-****-*** (Indonesian Mobile), E-mail Address: ********.******@*****.*** proper implementation of explosion protection method (e.g., flame arresters, pressure relief systems, ventilation) as per the design requirements and applicable safety regulations. 4. Ensure that, quality installation of all Ex-equipment and accessories are complying with the latest project drawings, specifications, manufacturer instruction, safety rule, and good practice. Conduct regular audits and safety inspections of construction areas of improvement and ensuring that construction methods and equipment meet explosive environment safety standards.

5. Site surveillance to check the construction work and give comments if necessary, according to standard (hook up, P & ID drawing, etc.

6. Identify non-conformances and discrepancies related to explosive environment safety and work with the construction team to implement corrective actions and resolve issues promptly. 7. Completeness of the documentation that has not been issued by the vendors: Ex Registers, Ex Check Sheets. 8. Compilation of the Ex-Register and associated documentation for the entire scope of Topsides equipment. 9. Review of the documentation already supplied by the vendors: Ex Registers, Ex Check Sheets, Ex Certificates, all documentation to be countersigned on a randomized basis, as defined in the attached letter below, and check of the QAD. 10. IECEx final inspection as carry over on yard, when not completed on vendor's site. 11. Maintain comprehensive inspection records, including detailed reports of inspections, non-conformances, corrective actions and compliance with explosion protection standards. Report any discrepancies or risk asspciated with explosive environments to construction Ex Lead and Ex Engineering teams. Tripatra Engineers and Constructor November 2016 – August 2017 Electrical Commissioning Engineer, working on ENI Indonesia – Floating Production Unit (FPU) Jangkrik Project Job Summary :

Responsible for executing all electrical commissioning activities during both yard execution and offshore start-up phases. Ensure that all electrical systems packages are tested, energized, and ready for safe start-up and sustained operations. Collaborates closely with construction, mechanical, process, marine, vendors, and the commissioning integration team to deliver system completion, pre-commissioning, commissioning, and handover in accordance with project specifications and class requirements

(DNV/BV/ABS).

1. Preparation of Electrical Pre-commissioning and Commissioning Activities 2. To ensure that all construction equipment and all temporary facilities required for Electrical pre-commissioning and commissioning are provided in good time by the contractor. 3. To ensure that pre-commissioning and commissioning activities are performed by the contractor according to approved procedures and contract requirements, including, as applicable. 4. Provision of necessary pre-commissioning and commissioning spare parts, equipment, tools, instruments and fluids. 5. Commissioning preliminary checks, functional tests, operational tests, database, punch lists, hand-over dossier. 6. Performance of repair work for defective systems and re-testing as required. 7. To ensure that the pre-start-up activities are performed by the contractor according to approved procedures and contract requirements, including supply of operating consumables and first fills, and supply of spare parts. 8. To assists vendor performance such as:

Gas Turbine Generator (GTG) – Solar Turbine

Gas Turbine Compressor (GTC) – GE Electric

Navigation Aids and Foghorns – Orga

Pedestal Crane – Conacrane

UPS Battery System – GE Electric

9. To report on commissioning activities to Commissioning Manager. 10. Pre-start-up Activities

11. Coordination with Project Supervisory Team and Reporting. Tarpon Energy Services Indonesia June 2016 – November 2016 EEHA Certified E&I Inspector, working on ENI Indonesia – Floating Production Unit (FPU) Jangkrik Project Job Summary :

Responsible for all construction activities within explosive environments (classified areas) are conducted according to industry safety standards (e.g., ATEX, IECEx, NEC), project specifications and regulatory requirements. Verify the installation and compliance of explosion-proof electrical equipment, wiring and instrumentation. Inspect materials used in explosive environments to ensure they are suitable for use in hazardous areas. 1. Coordinate and organizing the daily inspection activities on equipment receiving and installation of electrical and instrument items.

2. Ensure that, quality installation of all Ex-equipment and accessories (Lighting & Small Power System, Grounding Systems, Pedestal Cranes and Hoists, Wellhead Control Panel (WHCP), Hydraulic Power Unit (HPU), Fire & Gas System, CCTV System, Telecom System etc) are complying with the latest project drawings, specifications, manufacturer instruction, safety rule, and good practice.

3. Site surveillance to check the construction work and give comments if necessary, according to standard (hook up, P & ID drawing, etc.

4. Completeness of the documentation that has not been issued by the vendors: Ex Registers, Ex Check Sheets. 5. Compilation of the Ex Register and associated documentation for the entire scope of Topsides equipment. 6. Prepared to check for ITR Sheet, MC Sheet and Completely all relevant document for Electrical / Instrument. 7. Construction correspondence, Request for Inspection, Document Transmittal, solved problem with the client. 8. Carry out final inspection for compliance and completeness prior to any equipment test. 9. Monitoring & Supervise E & I construction & Installation activity, Punch list Clearance. The Summer Residence Block C1/06 Batam Kota – Batam Centre, Batam, Kepri – Indonesia. 29464 Phone: +62-813*-****-***, +62-812*-****-*** (Indonesian Mobile), E-mail Address: ********.******@*****.*** O’Donnel Griffin (ODG) Indonesia November 2015 – June 2016 Senior Engineer E&I QA/QC, working on DSLNG Condensate Exporting phase II. Luwuk, Central of Sulawesi - Indonesia Job Summary :

Responsible for all construction activities of the Brownfield Refinery are conducted according to industry safety standards project specifications and regulatory requirements. Practices and knowledge of internal or external issues to improve the E&I inspection, will act as a resource for colleagues with less experience and share their conceptual and practical expertise related to the inspection discipline. Solves complex problems and uses discipline-specific knowledge appropriate guidelines and policies. 1. Prepared QA/QC documentation and E&I procedures. Supervise Quality Control activities to determine product conformity to customer specifications through independent inspection and tests by the Project Quality Plan. 2. Consult with the Project Quality Manager concerning prevention and appraisal resources and the effectiveness of the Project Quality Plan/Procedures necessary to achieve product quality. 3. Coordinate interface with Operations, Certifying Authority, Client, and contractor assuring the conformity to project specifications.

4. Elaborating and coordinating the E&I specifications, and codes/standards. 5. Coordination with the field subcontractors for all E&I procedure specifications and procedures qualifications reports. 6. Coordination with the other department (Mechanical, Piping and Structural) during fabrication. 7. Monitoring and control for equipment’s installation and continue energizing of all E&I equipment’s to Pre-Commissioning and Commissioning.

8. Collect of the E&I QA/QC reports daily and Auditing of the approved E&I Inspection. Collect E&I summary reports and Control the QA/QC site E&I inspectors

9. Prepared the inspection and testing methods and procedures for all E&I inspections 10. Coordinate the issue of nonconformance reports through the site QC manager 11. Prepared of the final handing over documents such as QA/QC documents, Inspection and Testing Reports. Saipem Snamprogetti Saudi Arabia Co.Ltd September 2014 – November 2015 EEHA Certified E&I Inspector, working on Saudi Aramco. Al Wasit Gas Plant Project, Offshore Gulf of Persia – Saudi Arabia. Job Summary :

Responsible for EIT Offshore activities are conducted according to industry safety standards (e.g., ATEX, IECEx, NEC) project specifications and regulatory requirements.

1. Coordinate and organizing the daily inspection activities on equipment receiving and installation of electrical items. 2. Prepared & check for all electrical & instrument drawing, standard drawing, material specification and brochure. 3. Ensure that, quality installation of all electrical equipment and accessories are complying with the latest project drawings, specifications, manufacturer instruction, safety rule, and good practice. 4. Check procedure of equipment test obtain the relevant document and manage documents certifying test. 5. Visual inspection and Monitoring of Cable Laying (Sub-Marine Cables) / Umbilical Cables during installation, as per drawing lay out, hook-up drawing, and General Arrangement drawing. 6. Monitoring Control Cable Tensioner during Cable Lay (Sub-Marine Cable) installation or Umbilical Cables. 7. Witness Cable Test Optical Time Domain Reflectometer (OTDR) for cable Telecom / Fiber Optic, Time Domain Reflectometer, Insulation Test, and grounding test.

8. Monitoring Post-Lay Trenching Cable by Trencher TM-04 Control Room during Trenching Cable lay installation. 9. Record of all relevant inspection activities and outstanding works. 10. Construction correspondence, Request for Inspection, Document Transmittal, solved problem with the client. 11. Prepared daily, weekly, monthly report to management. 12. Carry out final inspection for compliance and completeness prior to any equipment test. 13. Monitoring & Supervise E & I construction & Installation activity, Punch list Clearance. China Offshore Oil Engineering Company (COOEC) Ses.Ltd January 2014 – August 2014 E&I Commissioning Engineer, working on CNOOC– BANUWATI-K Gas Compressor Platform. Surabaya, Offshore – Indonesia. Job Summary :

Responsible for executing all electrical and instrument commissioning activities during both yard execution and offshore start- up phases. Ensure that all electrical systems packages are tested, energized, and ready for safe start-up and sustained operations. Collaborates closely with construction, mechanical, process, marine, vendors, and the commissioning integration team to deliver system completion, pre-commissioning, commissioning, and handover in accordance with project specifications and class requirements (DNV/BV/ABS).

1. Prepared of Electrical & Instrument Pre-commissioning and Commissioning Activities. Prepared of Electrical & Instrument Operation Test Procedure (OTP) as per Sub-System and Job Risk Assessment Also Lockout Tag out / LOTO Procedure. 2. Ensure that all construction equipment and all temporary facilities required for Electrical & Instrument pre-commissioning and commissioning are provided in good time by the contractor. 3. Ensure that pre-commissioning and commissioning activities are performed by the contractor according to approved procedures and contract requirements, including, as applicable. 4. Provision of

Contact this candidate