Grill Cook Line Operator

**/**** - **/**** ***** line operator

WM T.Burnett, Statesville, NC

Locate order # of fiber for work hours.locate fibers and set up in hoppers to run. program order recipe for order # load hoppers of correct fiber and maintain hoppers at running levels

to keep line running to produce rolls.maintain regular QC checks..and perform safety maintenance on line to assure lines operates and runs correctly. 06/2020 - 09/2023 Grill cook

Cookout, Statesville, NC

Prepare and cook food.read tickets and prepare for customers.maintain a clean and safe work area etc.

inventory goods and report.

05/2014 - 12/2019 Laborer, Construction Laborers

Roadmaster Traffic Control, Stony Point, NC

Perform tasks involving physical labor at construction sites. May operate hand and power tools of all types: air hammers, earth tampers, cement mixers, small mechanical hoists, surveying and measuring equipment, and a variety of other equipment and instruments. May clean and prepare sites, dig trenches, set braces to support the sides of excavations, erect scaffolding, and clean up rubble, debris and other waste materials. May assist other craft workers. 04/2012 - 09/2012 Textile Winding, Twisting, and Drawing Out Machine, Textile Winding, Twisting, and Drawing Out Machine Setters, Operators, and Tenders WT.BARNETT/ACCURATE, STATESVILLE, NC

Observe operations to detect defects, malfunctions, or supply shortages., Operate machines for test runs to verify adjustments and to obtain product samples., Record production data such as numbers and types of bobbins wound., Stop machines when specified amount of products has been produced., Clean, oil, and lubricate machines, using air hoses, cleaning solutions, rags, oilcans, and grease guns., Install, level, and align machine components such as gears, chains, guides, dies, cutters, and/or needles to set up machinery for operation., Repair or replace worn or defective parts or components, using hand tools., Measure bobbins periodically, using gauges; and turn screws to adjust tension if bobbins are not of specified size., Remove spindles from machines and bobbins from spindles., Inspect products to verify that they meet specifications and to determine whether machine adjustment is needed., Replace depleted supply packages with full packages., Start machines, monitor operation, and make adjustments as needed., Tend machines that twist together two or more strands of yarn or insert additional twists into single strands of yarn to increase strength, smoothness, and/or uniformity of yarn., Inspect machinery to determine whether repairs are needed., Observe bobbins as they are winding; and cut threads to remove loaded bobbins, using knives., Tend machines with multiple winding units that wind thread onto shuttle bobbins for use on sewing machines or other kinds of bobbins for sole-stitching, knitting, or weaving machinery., Tend spinning frames that draw out and twist roving or sliver into yarn., Thread yarn, thread, and/or fabric through guides, needles, and rollers of machines., Notify supervisors or mechanics of equipment malfunctions., Adjust machine settings such JAMES JOHNSON

511 Nathan Hunt Dr., High Point, NC 27260

Phone: 336-***-****

Alt Phone: 401-***-****

Email: **********@*****.***

Employment History

as speed or tension to produce products that meet specifications., Place bobbins on spindles and insert spindles into bobbin-winding machines. 05/2010 - 10/2011 Machine Feeders and Offbearers, Machine Feeders and Offbearers BIRD DOG TRAFFIC CONTROLLERS, STATESVILLE, NC

Inspect materials and products for defects, and to ensure conformance to specifications., Load materials and products into machines and equipment, or onto conveyors, using hand tools and moving devices., Remove materials and products from machines and equipment, and place them in boxes, trucks or conveyors, using hand tools and moving devices., Fasten, package, or stack materials and products, using hand tools and fastening equipment., Identify and mark materials, products, and samples, following instructions., Push dual control buttons and move controls in order to start, stop, or adjust machinery and equipment., Record production and operational data, such as amount of materials processed., Clean and maintain machinery, equipment, and work areas to ensure proper functioning and safe working conditions., Open and close gates of belt and pneumatic conveyors on machines that are fed directly from preceding machines., Shovel or scoop materials into containers, machines, or equipment for processing, storage, or transport., Weigh or measure materials or products to ensure conformance to specifications., Transfer materials and products to and from machinery and equipment, using industrial trucks or hand trucks.

03/2003 - 02/2005 Construction Laborers, Construction Laborers GARDEN RIDGE DIST., STATESVILLE, NC

Dig ditches or trenches, backfill excavations, and compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, and rakes., Shovel cement and other materials into portable cement mixers; and mix, pour, and spread concrete., Spray materials such as water, sand, steam, vinyl, paint, or stucco through hoses to clean, coat, or seal surfaces., Build and position forms for pouring concrete, and dismantle forms after use, using saws, hammers, nails, or bolts., Erect and disassemble scaffolding, shoring, braces, traffic barricades, ramps, and other temporary structures., Identify, pack, and transport hazardous and/or radioactive materials., Mix ingredients to create compounds for covering or cleaning surfaces., Tend machines that pump concrete, grout, cement, sand, plaster or stucco through spray-guns for application to ceilings and walls., Use computers and other input devices to control robotic pipe cutters and cleaners., Apply caulking compounds by hand or using caulking guns., Grind, scrape, sand, or polish surfaces such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines., Provide assistance to craft workers, such as carpenters, plasterers, and masons., Raze buildings and salvage useful materials., Load, unload, and identify building materials, machinery, and tools, and distribute them to the appropriate locations, according to project plans and specifications., Signal equipment operators to facilitate alignment, movement, and adjustment of machinery, equipment, and materials., Clean and prepare construction sites to eliminate possible hazards., Control traffic passing near, in, and around work zones., Lubricate, clean, and repair machinery, equipment, and tools., Measure, mark, and record openings and distances to lay out areas where construction work will be performed., Operate jackhammers and drills to break up concrete or pavement., Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.

03/1995 - 07/1999 Freight, Stock, and Material Movers, Hand, Material Moving Workers, All Other SPX CORP. METAL FORGE, ALBEMAMLE, NC

Adjusts or replaces equipment parts, such as rollers, belts, plugs and caps, using hand tools., Shovels materials, such as gravel, ice or spilled concrete, into containers, bins or onto conveyors., Sorts and stores items according to specifications., Installs protective devices, such as bracing, padding or strapping, to prevent shifting or damage to items being transported., Stacks or piles materials, such as lumber, boards, or pallets., Transports receptacles to and from designated areas, by hand or using dollies, handtrucks, and wheelbarrows., Cleans work area, using brooms, rags, and cleaning compounds., Reads work orders or receives and listens to oral instructions to determine work assignment., Secures lifting attachments to materials and conveys load to destination, using crane or hoist., Attaches identifying tags or marks information on containers., Records number of units handled and moved, using daily production sheet or work tickets., Bundles and bands material, such as fodder and tobacco leaves, using banding machines., Directs spouts and positions receptacles, such as bins, carts, and containers, to receive loads., Loads and unloads materials to and from designated storage areas, such as racks and shelves, or vehicles, such as trucks., Assembles product containers and crates, using hand tools and precut lumber. High School Equivalency Diploma

,, None Selected

Conversion Record

Education History

Contact this candidate