Apprentice Electrician Warehouse Associate
Resume:
Eleazar Castaneda
I am a highly experienced and motivated electrician with journeyman level skills. I am capable of most tasks I can read blueprints, troubleshooting, operate scissor lifts and manlifts.
Corpus Christi, TX 78416
adwbhl@r.postjobfree.com
Authorized to work in the US for any employer.
Work Experience
Electrician
Caverly Electrical Services – New Braunfels, TX
November 2022 to January 2023
I was a terminator on DC/AC devices. Terminations included motors and motor controls, start/stop switches, conveyor controls and small cranes. Terminations were from blueprints approved by engineers approval. Cables were installed with engineers approved allowable slack. Cables were cut, stripped, lugged, crimped and terminated with engineer approval.
Electrician
Southwest Electric Contracting Services – Converse, TX
July 2022 to October 2022
I measured, fabricated, cut, installed EMT conduit for lighting and power circuits. Lighting terminations and power terminations, measured, cut and installed cable tray for low voltage wiring. Most work was done from heights above thirty feet.
Electrician
Cashe Valley Electric – Salt Lake City, UT
September 2020 to June 2021
I measured, cut, fabricated and installed Ridgid and EMT conduit, using hydraulic benders and Chicago benders. Power pony threaded and hand threaders were used on various sizes of conduit for specific equipment such as motors, lights, controls cabinets and transformers.
Electrician
Wesley Crow – Lampass, TX
July 2018 to June 2019
Corpus Christi navel air station. I completed duct bank 6” pvc to 6” play station. I worked on the fabrication of whips to light fixtures from j boxes. I ran Ridgid conduit for outside receptacles and fire alarm. I ran EMT for lighting, receptacles and fire alarm inside building I used scissor lifts that were inspected daily. Ran conduit for air cleaners.
Electrician
Bay Ltd – Corpus Christi, TX
March 2017 to May 2018
I worked on offshore living quarters. I cut and fabricated cable tray, EMT and Ridgid conduit. I ran wire for power to lighting and receptacles. Lighting and receptacles for kitchen movie theater, rooms for rig employees. Ran power for transformers to panels that had main disconnect.
Electrician
Strong Electric – Marble Falls, Tx
August 2016 to February 2017
Worked at hospital I had to measure, bend cut and install EMT and Ridgid conduit. I pulled wire for normal power and emergency power systems. For lighting, receptacles, panels, transformers, and lighting contactors with terminations. I was later sent to Austin TX to complete work on large hotel,
where I worked on lighting for stair case and emergency lighting.
Electrician
Franchise Electric – Corpus Christi, TX
August 2011 to May 2015
As a residential electrician I wired new home by code with city of Corpus Christi. They included GFCI and AFCI. I ran wire for receptacles double oven cooktops, water heaters A/C units and terminate when house was ready for trim out as well as light and disconnects for A/C and water heaters.
Apprentice Electrician
Scott Electric – Corpus Christi, TX
August 2008 to October 2011
I studied at NJATC working for Scott Electric. I learned to measure, bend, cut, thread Ridgid conduit using Chicago bender and electric benders. As an apprentice I helped with the installation of panels, disconnects, start/stop controls where I learned to terminate light receptacles and repair lighting
fixtures.
EDUCATION
High school or equivalent
Skills
Warehouse Associate
Electrical Experience (10+ years)
Construction (10+ years)
Mechanical knowledge (5+ years)
Blueprint Reading (5 years)
Low Voltage
NEC
Welding
Troubleshooting (10+ years)
Cabling
High Voltage (5 years)
Fabrication (10+ years)
English (10+ years)
Industrial electrician experience (4 years)
Communication skills
Certifications and Licenses
Apprentice electrician
October 2008 to present
I fabricate and install most electrical devices.
TWIC Card
October 2023
Contact this candidate