Professional Summary

Experience

DAVID HENDRICKS

*** ** ****, ** *****, TX 75639 (H) 936-590-896 ads27t@r.postjobfree.com Service-oriented labor hand with a background of 20 years of hard work, an dedication. Core competencies include oilfield work, construction, and production as well as excellent communication and time management skills. Handles tasks with accuracy and efficiency.

Floor hand 03/2017 to 12/2019

Royalty Well Service – Marshall, TX

Keep pipe deck and main deck areas clean and tidy. Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.

Supply equipment to rig floors as requested, and provide assistance to roughnecks.

Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.

Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.

Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.

Bolt or nail together wood or steel framework to erect derricks. Bolt together pump and engine parts.

Perforate well casings or sidewalls of boreholes with explosive charges. Install pressure-control devices onto wellheads.

Thread cables through derrick pulleys, using hand tools. Operate specialized equipment to remove obstructions by backing-off or severing pipes by chemical or explosive action.

Close and seal wells no longer in use.

Field hand 04/2017 to 11/2017

Lesco Inc – Bethany, LA

Observe load variations on strain gauges, mud pumps, and motor pressure indicators; and listen to engines, rotary chains, and other equipment in order to detect faulty operations or unusual well conditions. Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil. Examine unserviceable wells to determine actions to be taken to improve well conditions.

Install pressure-control devices onto wellheads.

Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.

Clean or prepare construction sites to eliminate possible hazards. Transfer tools, parts, equipment, and supplies to and from work stations and other areas.

Install or replace machinery, equipment, and new or replacement parts and instruments, using hand or power tools.

Adjust, connect, or disconnect wiring, piping, tubing, and other parts, using hand or power tools.

Clean and prepare sites for excavation or boring.

Clean up work areas and remove debris after extraction activities are complete.

Disposal laborer 12/2016 to 03/2017

Big Foot Energy Services – Gary City, TX

Patrol work areas to ensure that solutions in tanks or troughs are not in danger of overflowing.

Notify maintenance, stationary-engineering, or other auxiliary personnel to correct equipment malfunctions or to adjust power, steam, water, or air supplies.

Inspect operating units, such as towers, soap-spray storage tanks, scrubbers, collectors, or driers to ensure that all are functioning and to maintain maximum efficiency.

Turn valves to regulate flow of products or byproducts through agitator tanks, storage drums, or neutralizer tanks.

Direct workers engaged in operating machinery that regulates the flow of materials and products.

Gauge tank levels, using calibrated rods.

Repair or replace damaged equipment.

Regulate or shut down equipment during emergency situations, as directed by supervisory personnel.

Control or operate chemical processes or systems of machines, using panelboards, control boards, or semi-automatic equipment. Move control settings to make necessary adjustments on equipment units affecting speeds of chemical reactions, quality, or yields. Monitor recording instruments, flowmeters, panel lights, or other indicators and listen for warning signals, to verify conformity of process conditions. Compressor Machanic 07/2013 to 05/2016

James Compressor repair service – Deberry, Tx

Disassemble machinery or equipment to remove parts and make repairs. Repair or replace broken or malfunctioning components of machinery or equipment.

Examine parts for defects, such as breakage or excessive wear. Reassemble equipment after completion of inspections, testing, or repairs. Observe and test the operation of machinery or equipment to diagnose malfunctions, using voltmeters or other testing devices. Operate newly repaired machinery or equipment to verify the adequacy of repairs.

Clean, lubricate, or adjust parts, equipment, or machinery. Cut and weld metal to repair broken metal parts, fabricate new parts, or assemble new equipment.

Install repaired equipment in various settings, such as industrial or military establishments.

Perform scheduled preventive maintenance tasks, such as checking, cleaning, or repairing equipment, to detect and prevent problems. Set up and test industrial equipment to ensure that it functions properly. Repair or adjust equipment, machines, or defective components, replacing worn parts, such as gaskets or seals in watertight electrical equipment. Concrete worker 02/2012 to 05/2013

C H Construction – Center, TX

Control traffic passing near, in, or around work zones. Clean or prepare construction sites to eliminate possible hazards. Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.

Read plans, instructions, or specifications to determine work activities. Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.

Measure, mark, or record openings or distances to layout areas where construction work will be performed.

Mix ingredients to create compounds for covering or cleaning surfaces. Mix, pour, or spread concrete, using portable cement mixers. Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt. Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.

Grind, scrape, sand, or polish surfaces such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.

Operate jackhammers or drills to break up concrete or pavement. Transport or set explosives for tunnel, shaft, or road construction. Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.

Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.

Position, join, align, or seal structural components, such as concrete wall sections or pipes.

Laborer 02/2009 to 03/2012

Steel Building Supply, Inc – Center, TX

Shape or cut materials to specified measurements, using hand tools, machines, or power saws.

Follow established safety rules and regulations and maintain a safe and clean environment.

Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.

Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.

Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.

Select and order lumber or other required materials. Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue. Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.

Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.

Erect scaffolding or ladders for assembling structures above ground level. Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.

Roustabout laborer 06/2006 to 08/2009

Surface Rental equipment, roustabout services – Timpson, TX Guide cranes to move loads about decks.

Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.

Supply equipment to rig floors as requested, and provide assistance to roughnecks.

Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.

Clean up spilled oil by bailing it into barrels.

Dig drainage ditches around wells and storage tanks. Bolt or nail together wood or steel framework to erect derricks. Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.

Set up or operate machines or systems to crimp, cut, bend, form, swage, flare, bead, burr, or straighten tubing, according to specifications. Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes. Lead man- sanitation 01/2003 to 02/2006

Tyson Foods Inc – Center, TX

Enforce safety and sanitation regulations.

Direct and coordinate the activities of employees engaged in the production or processing of goods, such as inspectors, machine setters, and fabricators. Inspect materials, products, or equipment to detect defects or malfunctions. Observe work and monitor gauges, dials, and other indicators to ensure that operators conform to production or processing standards. Calculate labor and equipment requirements and production specifications, using standard formulas.

Set up and adjust machines and equipment.

Clean and sanitize work areas, equipment, utensils, dishes, or silverware. Remove trash and clean kitchen garbage containers. Specify food portions and courses, production and time sequences, and workstation and equipment arrangements.

Inspect supplies, equipment, and work areas to ensure efficient service and conformance to standards.

Develop equipment maintenance schedules and arrange for repairs. Floor hand 05/2003 to 12/2003

Nabors Drilling – Kilgore, TX

Inspect derricks, or order their inspection, prior to being raised or lowered. Inspect derricks for flaws, and clean and oil derricks in order to maintain proper working conditions.

Control the viscosity and weight of the drilling fluid. Repair pumps, mud tanks, and related equipment.

Set and bolt crown blocks to posts at tops of derricks. Listen to mud pumps and check regularly for vibration and other problems, in order to ensure that rig pumps and drilling mud systems are working properly.

Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill-cuttings.

Position and align derrick elements, using harnesses and platform climbing devices.

Guide lengths of pipe into and out of elevators.

Prepare mud reports, and instruct crews about the handling of any chemical additives.

Clamp holding fixtures on ends of hoisting cables. Weigh clay, and mix with water and chemicals in order to make drilling mud, using portable mixers.

String cables through pulleys and blocks.

Steady pipes during connection to or disconnection from drill or casing strings.

Welder 04/2001 to 06/2003

General Shelters of Texas – Center, TX

Weld components in flat, vertical, or overhead positions. Operate safety equipment and use safe work habits. Lay out, position, align, and secure parts and assemblies prior to assembly, using straightedges, combination squares, calipers, and rulers. Examine workpieces for defects and measure workpieces with straightedges or templates to ensure conformance with specifications. Recognize, set up, and operate hand and power tools common to the welding trade, such as shielded metal arc and gas metal arc welding equipment.

Weld separately or in combination, using aluminum, stainless steel, cast iron, and other alloys.

Clamp, hold, tack-weld, heat-bend, grind or bolt component parts to obtain required configurations and positions for welding. Select and install torches, torch tips, filler rods, and flux, according to welding chart specifications or types and thicknesses of metals. Ignite torches or start power supplies and strike arcs by touching electrodes to metals being welded, completing electrical circuits. Connect and turn regulator valves to activate and adjust gas flow and pressure so that desired flames are obtained.

Determine required equipment and welding methods, applying knowledge of metallurgy, geometry, and welding techniques.

Operate manual or semi-automatic welding equipment to fuse metal segments, using processes such as gas tungsten arc, gas metal arc, flux-cored arc, plasma arc, shielded metal arc, resistance welding, and submerged arc welding.

Monitor the fitting, burning, and welding processes to avoid overheating of parts or warping, shrinking, distortion, or expansion of material. Mark or tag material with proper job number, piece marks, and other identifying marks as required.

Analyze engineering drawings, blueprints, specifications, sketches, work orders, and material safety data sheets to plan layout, assembly, and welding operations.

Prepare all material surfaces to be welded, ensuring that there is no loose or thick scale, slag, rust, moisture, grease, or other foreign matter. Guide and direct flames or electrodes on or across workpieces to straighten, bend, melt, or build up metal.

Clean or degrease parts, using wire brushes, portable grinders, or chemical baths.

Use fire suppression methods in industrial emergencies. Cut, contour, and bevel metal plates and structural shapes to dimensions as specified by blueprints, layouts, work orders, and templates, using powered saws, hand shears, or chipping knives.

Operate brazing and soldering equipment.

Melt lead bars, wire, or scrap to add lead to joints or to extrude melted scrap into reusable form.

Stocker 06/2000 to 04/2002

H-E-B grocery – Center, TX

Stock shelves, racks, cases, bins, and tables with new or transferred merchandise.

Requisition merchandise from supplier based on available space, merchandise on hand, customer demand, or advertised specials. Clean display cases, shelves, and aisles.

Design and set up advertising signs and displays of merchandise on shelves, counters, or tables to attract customers and promote sales. Receive, open, unpack and issue sales floor merchandise. Transport packages to customers' vehicles.

Pack customer purchases in bags or cartons.

Compare merchandise invoices to items actually received to ensure that shipments are correct.

Contact this candidate