Technician Maintenance Safety Officer

RICHARD V. AMBRE III

**** ** ****** ***., *** Vegas, NV 89102

H-702-***-****; C-702-***-****

*********@***.***

OBJECTIVE

Seeking a position as a Technician / Analyst where my technical aptitude, communication skills and experience can benefit both employer and myself.

EXPERIENCE

Sable Systems International Mar 22 – Jun 22

Built Components for Mouse and Rat cages for research facilities.

Soldered wired to circuit board for load cells, replaced LED emitters and sensors on circuit boards to ensure compliance with testing of circuit boards

Q Corporation: Nov 21 – Mar 22

Perform Electrical and electronic services, Solder wiring, Install and wire panels.

Install Conduit from box or component to panel pulling wire from 14 Ga to 3/0.

Driver: Roush Automotive thru Cornerstone Staffing Solutions: June 21 – Aug 21

Drive pre-designated routes to achieve 300 miles per shift

Evaluate Capabilities of new prototype automotive industry vehicles gas, hybrid and all electric

Drive both left and, right hand steering wheel vehicles

Personal Care Assistant: Giving Home Health Care: Aug 2020 – Present

Read clients Newspaper, E-Mails and US mail

Assist client in depositing checks and withdrawing funds

Monitor client’s med’s, take shopping, Dr’s as needed.

Adv. Electronics Tech II: General Dynamics: June 2018 – Apr 2020

Perform manufacturing and test analysis of electronic modules for flight, and space applications.

Perform SMD, and thru hole soldering of board components, and test chassis manufacturing

Manufactured STE test boxes, and performed physical mechanical modification with Bridgeport mill under machinist supervision.

Collaborate with engineers on the manufacture, and test of Digital, and RF flight module. Module Delivered to JPL for Aug 22 launch. (16-Psyche)

Engineering Technician: Jacobs Engineering: January 2018 – February 2018

Evaluate effectiveness of new gate pass recognition system

Job cut short following govt shutdown in Jan2018

Electrical/Electronics Technician: Hyperloop One: February 2017 – July 2017

Performing various electrical/electronic installation works, from switch gear to outlets, move 10KV generators and reconnect power.

Built CAT5 (e)/6(a) cables and installed strain/accelerometer gauges and, soldered on vertical surfaces.

Operate off-road 25k Fork-lift, and 20-60’ Bucket Truck, Man-Lift(Vert) for daily operation.

Computer / Electronics Technician: Blind Center of Nevada (BCN): August 2015 – March 2016

Primary responsibility for repairing computer s and servers, wiping hard drives, repair (board level) of flat-screen monitors/TV’s of donated equipment for reuse, resale, to raise monies for the BCN.

Air Quality Technician: Clark County Dept. of Air Quality: February 2014 – January 2015

Supported EPA requirements for maintaining air quality measurement equipment.

Performed various electronic, chemical, and HVAC maintenance and, tower isolation duties for lighting protection.

Updated air quality records prior to the release of air measurement data to the EPA and public websites.

Electronics Tech III w/Lead (Technical Lead): JT3: February 2000 – July 2013

Conducted training for technicians and engineers on all aspects of RF on our transmitters, receivers, and their control circuitry.

Installed Antennas in top of 40’, 80’ and 100’ towers using climbing or 120’ Articulating manlift as needed.

Generated the Standard Operations Procedures (SOP) for Operations and Maintenance (O&M) and military personnel.

Developed the current Range Safety Officer (RSO) SOP in use at the Nevada Test & Training Range (NTTR).

Collaborated with engineers on the development of test procedures and inspection documents for the review of technician maintenance and performing spot checks and records.

I collaborated with engineering personnel in the requirements for the Developmental Test & Evaluation (DT&E) and Operational T & E (OT&E) documents for the certification of the “New Computer Control” and the “Remote Control Operation” of the range transmitter systems.

In this position I was able to increase training on topics that applied to fundamental concepts of amplitude modulation, angle and pulse modulation, and demodulation techniques.

Responsible for identifying, reporting and fixing problems associated with our transmitter systems and exterior integrated systems.

ACCOMPLISHMENTS/SKILLS

Took the lead position on the range for getting our transmitters Range Commanders Council (RCC) EFTS compliant.

Acting Forklift trainer 4K-25K, Fall Arrest Trainer, CPR First Aid

EDUCATION

USN – Electronics “A” School and follow on “C” School; Shop Lead/Senior Tech in the HF, UHF and Sat Comm. shops

CSN – AS in Science w/Honors 5/2015 and AA in Gen Studies 5/2015

CBT – Microsoft Office2010, AutoCAD, and Visio

TLC – A+, Net+, Sec+ Training

HOBBIES

Volunteer – Vitalant (Pheresis Doner), Valley Vegas Churches

ITEA – Member

MIT OCR - Educational programs and donor.

Contact this candidate