Mechanical Engineer Design

Yahya Al-Rawashdeh

(Mechanical HVAC Engineer)

Yahya Awad Yousef Al-Rawashdeh

Mobile : +962-*********

Email: ***.**************@*****.***

Birth Date : 12/3/1994 Gender: Male Status: Single Nationality: Jordanian Address: Amman – Jordan

Driving License: Available

Career Objective

An enthusiastic self-starter Mechanical engineer keen to gain new experiences and knowledge by seeking a challenging career with a progressive organization allowing me to utilize and build upon my skills in fields of HVAC engineering.

Education History

- Al Balqa' Applied University (BAU), Faculty of Huson College, Irbid –Jordan Bachelor Degree in Mechanical Engineering (September 2012, September 2016)

(Heating, Ventilating, and Air Conditioning (HVAC) Program), Rating: very good with GPA of (3.36/4.00)

Graduation Project: “Heat recovery from chimney in rehab power thermal and use this heat for air- conditioning of facilities by using absorption chiller”. Experience and Training

MANTEQ Engineering Company

Position: Technical & Design Engineer of HVAC systems (Oct, 2016 - Present) Technical sales & design engineer in this company, and responsible for the design of HVAC systems especially in VRF systems & HVAC commercial systems, and providing technical advice to customers in this field of Air-conditioning and mechanical ventilation systems.

Job Description: -

HVAC-systems Section:-

- Design of air conditioning systems for residential and commercial applications like (VRF, Chiller, Package Unit, FCU, AHU and concealed ducted split systems) by using some international references like ASHRAE 2017 handbook, ASHREA 62.1,ASHREA 2013 and local codes.

-

- Design of fresh, exhaust, smoke management control systems, pressurization systems, and kitchen hoods by using some international references like ASHRAE 62.1, SMACNA, British Standard, NFPA92B, NFPA 101 and local codes.

- Making a good selection & preparing submittals & compliance sheet for fans, VRF systems (indoor and outdoor) for VRF, CAC & AHU’s systems by using special software.

- Preparing submittals for fans & and compliance sheets.

- Get operation approval from the local authorities like Civil Defense for ventilation systems.

- Preparing Purchase orders for these systems.

References

Fire System Section:

- Design of wet and dry sprinkler system by using international and local code standards NFPA13.

- Design of hose cabinet and fire hydrant systems by using international and local code standards NFPA14.

- Design of the Foam-Water Sprinkler and Foam-Water Spray Systems by using international and local code standards NFPA16

Design of Pluming System (2020)

Centrifugal Pumps in Residential Applications (2018)

(Description of centrifugal pumps, principle of works, components, some problems and solutions)

Design and Requirements of Firefighting Systems (2018) Design of firefighting system like (sprinkler system, fire hydrant, fire hose reel, fire cabinet, foam system, landing valve and Siamese system)

Smoke Management System Design (2018)

Design of (smoke control for cellars 6 ACH, 10 ACH, pressurization stair case, refuge area & fire fighter lift)

REVIT MEP Course (2017)

Design Mechanical (Pluming, HVAC & Firefighting) systems by using all tools of software

Introduction to Chilled Water System Design (2017) Description of chilled water system (type of chillers based on compressor and condenser, primary and secondary pump, estimate the head of pumps)

Hourly Analysis Program (HAP) (2015 – Present)

(Calculation of cooling and heating load by using HAP) scope of my job Skills and Interests

Language Skills

Arabic: Native Tongue.

English: Very good written and spoken.

German: Beginner (A2 Level)

Personal Skills

- Leadership skills (A member of the Student’s Union).

- Excellent communication skills.

- Strong sense of responsibility and self-motivation.

- Enjoy a challenge, work well under pressure.

- Open minded, interactive, fast learner and grasp knowledge quickly.

- Time management and planning skills.

- Team work with the ability to work independently. Computer Skills

AutoCAD HAP Firefighting MS Office Rivet (MEP). References are available upon request.

Certificates and Courses

Contact this candidate