Mechanical Engineer
Resume:
Eric C. Shaw
Wichita, Kansas ***18
********@*****.***
Objective:Seeking a position as a Sheet metal mechanic or Fabricator. Experience:
Sheet Metal Mechanic, Brittain Machine, Wichita, Kansas02/15 to Present
● Jig Driller of Steel, Titanium
● Use of countersinks, dotco, hand drills
● Adhesives, sealants, paints
Composite Trim, Goodrich Aerospace, Wichita, Kansas 11/13 to 12/14
● Trim and edge filler of aircraft composite parts
● Use of routers, sanders, drills, countersinks,
● Adhesives, epoxy, resins, sealants, ad-tech 15-4 Assembler,Case New Holland,Wichita, Kansas 09 /11 to 11/13
• Installation of HVAC, Duct work
• Clean containers, materials, supplies, or work areas, using cleaning solutions and hand tools.
• Examine and inspect containers, materials, and products to ensure that packing specifications are met.
• Load materials and products into package processing equipment.
• Mark and label containers, container tags, or products, using marking tools Kitting Department, Adecco/LRI/Spirit AeroSystems,Wichita, Kansas 09/10 to 10/11
• Assemble, line, and pad cartons, crates, and containers, using hand tools.
• Clean containers, materials, supplies, or work areas, using cleaning solutions and hand tools.
• Examine and inspect containers, materials, and products to ensure that packing specifications are met.
• Load materials and products into package processing equipment.
• Mark and label containers, container tags, or products, using marking tools
• Pick parts for 777,787,737,7E7, perform kitting and bagging of aircraft parts to be delivered to different department
Mechanic/Plumber, Hawker Beechcraft, Wichita, Kansas 02/07 to 12/08
• Adjusted and set mechanical controls and components
• Aligned and adjust clearances of mechanical components or parts
• Aligned and adjust clearances of vehicle body parts or components and frames
• Installation of plumbing in the aft section of the Premier Jet, sealants, composites, inspections, honeycomb repair
Mechanic Spirit AeroSystems, Wichita, Kansas 2/06 to 2/07
• Assembled and installed electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools
• Accompanied aircraft on flights to make in-flight adjustments and corrections
• Checked for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment
• Cleaned engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels
• Cleaned, refueled, and changed oil in line service aircraft
• Fitted and assembled of 360 join on the 737, drill out, countersink, and installation of rivets, use of bucking bars, use of k-nar guns, drills, rivet guns, sealants, inspections, hi-loks, fasteners
• Mechanical, and pneumatic testing of equipment
Service Technician, Lopez HTG/AC San Antonio, Texas 5/96 to 1/06
• Adjusted and replaced worn or defective mechanisms and parts, and reassembled repaired systems.
• Serviced of all residential and commercial heating and air conditioning systems, freon charge, wiring of thermostats, condensers, and furnaces
• Adjusted valves according to specifications and charged system with proper type of refrigerant by pumping the specified gas or fluid into the systems
• Brazed or soldered parts to repair defective joints and leaks
• Cut, bent, thread, and connected pipes to functional components and water, power, or refrigeration system
• Dismantled malfunctioning systems and test components, using electrical, mechanical, and pneumatic testing equipment
Refrigeration Engineer, Ohse Meats Wichita, Kansas 04/92 to 2/96
• Adjust valves according to specifications and charge system with proper type of refrigerant by pumping the specified gas or fluid into the system.
• Adjust or replace worn or defective mechanisms and parts, and reassemble repaired systems.
• Braze or solder parts to repair defective joints and leaks.
• Cut, bend, thread, and connect pipe to functional components and water, power, or refrigeration system.
• Dismantle malfunctioning systems and test components, using electrical, mechanical, and pneumatic testing equipment.
Education:
Wichita Area Vo-tech Wichita, Kansas
HVACR, Certificate1992
Wichita Heights High Wichita, Kansas
Diploma1982-1985
WorkReady Certificate Wichita, Kansas
Silver2010
Contact this candidate