Partha Das Purkaistha
Hamtramck, MI 313-***-**** adilk7@r.postjobfree.com adilk7@r.postjobfree.com
Resume Objective:
A technical minded,recent graduate with master’s in Electrical Engineering looking for an Entry Level Electrical Engineer position that will enable me to use my strong communication skills and educational background.
Education
Wayne State University, Detroit, MI Graduated April 2020
Major: MS in Electrical Engineering GPA: 3.83
UCSI University,Kualalumpur,Malaysia Graduated April 2011
Major: BS in Electrical & Electronics Engineering
Relevant Coursework
Embedded Systems Design, Modelling & Control of Power Electronics & Electric Vehicle Powertrains, Computer-Aided Logical Design and FPGAs,Cumputer Networks & Programming, Mixed Signal Circuit Design, Introduction to VLSI Systems,Fuzzy Systems, Advance Energy Storage Systems for Electric Vehicle.
Technical & Computer Software Skills
MATLAB & Simulink, Embedded C/C, Python, Verilog, CAN BUS protocol, Pspice,Cadence virtuoso, Vivado Xilinx FPGA, MS Office.
Engineering Projects
Sensor Data Monitoring System Over CAN BUS Protocol Using Arduino:
Understand, designed & developed a functional model of embedded system using Arduino,MCP2515 CAN module, sensors including DHT11,Ultrasonic sensor, Door magnetic sensor, potentiometer and I2C LCD display. In the first part, used embedded C to program Arduino to implement CAN bus network of two nodes(transmitter & Receiver).In second part, built hardware model of CAN bus network(2 nodes),tested sensor & CAN module connection to both nodes with code. Configured CAN Bus message identifiers and data format, data length on actual CAN Bus hardware.
Modelling and Simulation of Electric Vehicle Using MATLAB:
Built a Simulink model to analyze vehicle dynamics, power(regen and without regen),energy(battery sizing of an electric vehicle),SOC of battery. Developed MATLAB programs to calculate range, energy requirements for different driving cycles.
Using Socket Programming to Create Client – Server system:
A Cloud Database server has been created using low level socket programming. The project task was to establishing connection between two hosts on an internet network to communicate with each other. One socket listen on a port at an IP, on the other hand socket reaches out to the other to form a connection. Server forms the listener socket while client reaches to the server & implemented using Python.
UART Communication Between FPGA Board(Basys 3) and Computer Terminal:
An UART communication between the fpga board(Basys 3) and computer terminal has been established using UART transmitter and UART receiver through USB-UART connector on Basys 3.A-byte(8 bits) data/character(ASCII) has transmitted from FPGA board to computer terminal. On the other hand, 8 bits data send from computer terminal to FPGA board. Both UART transmitter & receiver is developed using Verilog code in the Vivado suite.
VLSI Implementation of 4-Bit Arithmetic Logic Unit(ALU):
A VLSI implementation of 4-bit ALU is done using Cadence in two parts. In the first part, Verilog code is created for ALU in both Vivado & NC sim.Then simulation & FPGA implementation has done to verify the functions. In the second part, logic synthesis,floorplanning,placement & routing is done using Cadence Encounter RTL compiler. Next pad frame generated for chip assembly & GDS file created to send MOSIS.
Battery Sizing for Off Grid Solar System for a Residential Flat:
Analyzed load demand of a Residential flat system and estimating daily household usage in watt-hour. Calculated battery bank capacity and array wattage based on the watt- hour requirements of the flat. Specified and calculated the inverter rating and number of solar panels required for the off grid solar system. Developed a DC-DC boost (MPPT) Controller for the off-grid system.
Academic Paper Presentation: (Wayne State University)
Course: Mixed Signal Circuit Design(2020)
Presentation Title: “High Resolution A/D Conversion in MOS/LSI”
Certifications:
Controller Area Network-In depth analysis of CAN BUS/Protocol-Udemy.
VLSI - Physical Design Flow-Udemy.
Other Professional Experience
Customer Service Associate at Walgreens, Warren, MI: Aug 2020 – Present
Cash Management and respond promptly and professionally to incoming customer inquiries in person, by telephone, or by email, Inventory managing.
Cashier at Jomir Grocery, Hamtramck, MI: Mar 2018 – Aug 2020
Receiving payment from customers by cash and credit cards and issue receipts, refunds, credits to customers and answered customers' questions, and provided information on procedures.
Senior Officer at Pubali Bank Limited,Dhaka,Bangladesh: Feb 2013 - Sep 2017
Meet with clients to obtain information for loan application &answer queries about process and types loan options. Analyze clients financial status, credit, and property evaluations to determine feasibility of granting loans. Create &compile loan proposal, application, financial statement analysis report. Helping payment schedules & loan recovery.