Engineer Tanveer Hussain

adik8c@r.postjobfree.com +92-321-*******

Diploma + 32 Years experience in electrical & Mechanical Field, Manufacturing Industry & Construction Yarn & Fabric Textile, Asphalt Plant, Food, Metal Printing, Plastic Molding,Boiler,cold storage,Army Buildings Professional Summery

• Familiar with NEC Codes 2008, Safety standards NFPA 70

• Design and commissioning testing, Inspection troubleshooting industrial (Low Voltage) electrical power & control systems, Switch Gear, Main Distribution Board, SMDB, UPS, Fire Pump, Lift station, HVAC, CCTV, fire alarm, battery charging room, Generator, ATS, transformer, PVC Cables 0.6Kv

(armored unarmored) cable race way and layout.

• Expert in Control Panel Assembly

• Installation, repair, testes branch circuits, conduit lines, switch boxes, lighting systems, fixtures, and other electrical equipment, AC/DC motors, control panels, PLC's, switches and transformers.

• Star Delta (Rev for) Automatic Power & Control Commissioning, Inspection, Testing, Troubleshooting

• Install, maintain, and troubleshoot relay logic, ladder diagrams, control components-- photo eyes, motor starters, relays, limit switches, proximity sensors, timers, solenoids, Servo drives, frequency inverters, linear drives, encoders, pressure transmitters, Transducer, Load Cell, Ignition transformer, temperature controller thermocouples solid state relays, power supplies 230 / 24 V DC

• Circuit Designing repairing & troubleshooting 24 VDC, 110 VAC, 230 VAC & 480 VAC

• 3 Phase Motor control, power maintenance overhauling 0.25 Kw – 250 Kw safeties, over temp, replacement bearing, daily routine checking and grease to prevent from maintenance procedure.

• PLC building & programming Mitsubishi, Fatek, Siemens S7 300, WinCC SCADA,weintek HMI, (Mtv- 100 with LED TV), VFDs, 0-10V, 4-20 m A Analog & Digital operating system

• Expert and resistance Utilize megger multimeters (volts, amps)

• AutoCAD Designing, Electrical Panel Scheduled, Single line drawing, power & control panels, fire alarm, cable tray, electrical shop drawings etc.

• Troubleshooting, Fire Pump, Sprinkling system, Surge Arresters, Lighting arresters, Cadweld joint

• Building Grounding & bonding, Cadweld joint, ground Rod 20mm x 3m

• Repairing, troubleshooting mechanical equipments, hydraulic, pneumatic systems, including rotating equipments, bearings, chains, sprockets and gear reducers diagnose and solve problems

• Knowledge of power and pneumatic tools drill, grinder, polisher, sander, screwdriver, wrenches and sockets and all kind of other tools.

• Knowledge of workshop equipment and their uses air compressor, cleaning equipment, grease gun, hoist, jack, lifting equipment, measuring equipment, diagnostic equipment

• Safely operate seizure lift, Lift truck, in cold & dry store.

• Logs scheduled inspection reports of the operating equipment, fixed building equipment and building structures, maintenance, repairs and other records and schedules.

• Must be able to stand/walk for up to 10-12 hours

• Ability to work all days and shifts, including overtime (24 hours a day, 7 days a week operation, including holidays)

• Willing to work flexible shifts depending on requirements.

• Motivated self-starter with the ability to work in a team and independently to able to lift 50 lbs. and pull 100 lbs. as required.

• Ability to pass a pre-employment physical, drug screen and background check Education

Diploma 1989 Sindh Board of Technical Education Karachi Pakistan GED or High School: 1985 Sindh Board of Secondary Education Karachi Pakistan Computer Skill

• PC Window, MS Office 2010, Excel, Word, Outlook, Power point, Paint & Internet etc

• Adobe Acrobat Reader & Writer multi functions files. PDF to Auto Cad to PDF, A4, A3

• AutoCAD 2D Classic, single line drawings shop lcontrol and power circuits.

• PLC Ladder Programming Mitsubishi, Fatek, Siemens S7 200, Weintek HMI, Mtv-100 Employment History

Electrical Engineer Advantech Automation & Control Lahore Pakistan Jan 2015 to Nov 2020

RESPONSIBILITIES:

• Installation, repairing Troubleshooting, Industrial electrical & electronics system. Control Assembly

• Injection Molding,Asphalt Plant, Concrete Plant, Metal Printing, Steam and thermo oil Boilers

,Install, maintain, and troubleshoot relay logic, ladder diagrams, control components-- photo eyes, motor starters, relays, limit switches, proximity sensors, timers, solenoids, Servo drives, frequency inverters, linear drives, encoders, pressure transmitters, Transducer, Load Cell, Ignition transformer, temperature controller thermocouples solid state relays, power supplies 230 / 24 V DC

• 3 Phase Motor control, power maintenance overhauling 0.25 Kw – 250 Kw safeties, over temp, replacement bearing, daily routine checking and grease to prevent from maintenance procedure.

• PLC building & programming Mitsubishi, Fatek, Siemens S7 300, WinCC SCADA,weintek HMI, (Mtv- 100 with LED TV), VFDs, 0-10V, 4-20 m A Analog & Digital operating system

• Heavy machinery control circuit troubleshooting Loader, Dynapac Roller, Motor Grader etc Project Engineer ANHAM FZCO Bagram Afghanistan

June 2012 to Jan 2015

Project Consists:

Industrial Refrigeration GEA Grasso Compressor Ammonia Gas Plant, Cold & Dry Store for Food Supply, covered area (200 x 154meter) 500 meter external area PLC Siemens S7-400, DCS, WinCC SCADA, Analog I/O, Pressure Transmitter, Level Sensor Sub Station 3 MW, Switchgear, MDP, SMDP, Lighting, UPS, Battery charging Room, Fire Alarm, Fire Pump, PA System, DFAC, ECP, Water filtration Plant, Laundry, Accommodation, Guard Tower, Officer Barracks, Lift Station & Electromechanical System .Auto sliding doors Installation testing inspection & Troubleshooting Major Duties:

• To look after all kind of Electrical construction work of the project

• Installation of GEA Grasso ammonia Compressor and other components

• Installation of Hi Bay Lighting system in Cold & Dry Store

• Installation of Auto Sliding door & motion control with FRABA safety

• Preparation of Drawing for sub contractors

• New Designing testing, inspection for all kind of Electrical Panel,

• Preparation of Material Submittals

• Installation of new Lift Station Automatic.

• Security System, Fire alarm, Sprinkling system & Fire Pump installation

• Power distribution system for Battery Charging room Site Engineer IECC Engineering & Construction Afghanistan Dec 2011 to May 2012

Project Consists:

New Designing and installation of Electrical Sub Station, Switchgear,Load Bank, MDP,External Power Distribution,Internal Power distribution System,Sub Panels for Living Accommodation, Kitchen, DFAC, Laundry, Guard Tower Officer Barracks,, HVAC and New Lift Station. Major Duties:

• To look after all kind of Electrical work of the project.

• Preparation of Shop Drawings.

• New Designing scheduled of Electrical Panel,

• Preparation of Material Submittals.

• Installation of new Lift Station Automatic.

• Security System & Fire alarm.

Electrical Engineer Asia Construction & Logistics Kandahar Air Field Aug 2011 to Nov 2011 Afghanistan

Project Consists:

New Designing and installation of Electrical Switchgear,Load Bank, MDP,Sub Panels for Living Accommodation, Kitchen, DFAC, Laundry, Guard Tower and HVAC and New Lift Station. Project Engineer Istanbul Construction / USA Consulate Office & Camp Dec 2010 to July 2011 Little Bear US Training Center Mazar Shareef Afghanistan Project Consists:

New Designing and installation of 2 Generator 1500Kva,SWGR,MDP,Armored and Unarmored Cables,Sub Panels for Warehouse, MWR, Kitchen, DFAC, Laundry, Armory Room, Guard Tower and HVAC and New Lift Station and CCTV.

Site Engineer Specific Engineering & Construction

June 09 to Jan 2010 Mazar Shareef Afghanistan

Project Consists:

SOW, Fire Alarm, Water Pump Control System for all Storage (Port Hairatan) Nearby Uzbekistan. Site Engineer Encorp International Camp Phoenix Phase II Kabul Afghanistan May 08 to June 09

Project Consists:

Client: US Army Corp of Engineering

Main Contractor: CH2m Hill (USA)

Designing and Construction for 5 Billets, Gymnasium, Auditorium & Transbillet. Maintenance Engineer Sarah Textile Lahore Pakistan Oct 1994 - Nov 2008

Duty Timing Details:

Gen shift 9am to 5pm

1st Shift: 7am to 3pm

2nd Shift: 3pm to 11pm

3rd Shift: 11pm to 7am

Responsibilities:

• General Maintenance,

• Inspection, Testing, Troubleshooting of power and control panels.

• Safety system

• Electric Motors 0.25 to 200kw Overhauling.

• New Control Circuit designing all kind.

• Implemented power lighting, Fire alarm system.

• Installation and Termination of cables at distribution panel

• Lying of main duct bank, Low Voltage Cable and its Termination at Main Switch Board.

• Installation and Termination of cables at distribution panel Electrical Technician Nishat Group of Company (Textile Industry) Mar 90 - June 94

Duty Timing Details:

Gen shift 8am to 4pm

1st Shift: 6am to 2pm

2nd Shift: 2pm to 10pm

3rd Shift: 10pm to 6am

Responsibilities:

• General Maintenance, Inspection, Testing, Troubleshooting of power & control panels, VFD, Pressure transmitter, PLC I/O Analog, Water Turbine, Treatment filtration Plant

• Substation Breakers inspection testing and replacement

• MDP, SMDP, Panels inspection testing and troubleshooting

• LV Unarmored cables installation testing troubleshooting and replacement

• Electric Motors 0.25 to 200kw Overhauling.

• Control Circuit designing 24V – 480V

Language

English: Good command in both spoken and written

Dari: Normal

Punjabi: Normal

Urdu: (Mother Tongue).

Security Clearance

Security Clearance: Confidential (Clear from Government of Pakistan) Personal

Name: Tanveer Hussain

Status: Unemployment and Available

Availability Immediately

Travel: Willing to Relocate international

Passport No: MY6892602

Date of issue: 12/20/2018

Date of expire: 12/19/2024

Driving License: 582 - Sheikhupura Pakistan

Contact No: +92-321-*******

Email: adik8c@r.postjobfree.com

Address: House 109B Tajpura Scheme

City: Lahore

Country: Pakistan

Zip Code: 54870

https://www.linkedin.com/in/tanveer-hussain-17774228/

Contact this candidate