Electrical Maintenance Technician

Bernard Renteria

**** *.******* ****** ******, Ca 93722 559-***-**** ***************@*****.***

Skills:

• RSLogix5000 (PLC)

• Telepace (SCADA)

• Industrial Robotics (FANUC)

• Instrumentation Calibration

• Motor Controls

• Electrical Schematic Reading

• Facility Automation

• Variable Frequency Drives

• Blueprint Reading

• National Electrical Code (NFPA70)

• Electrical Safety (NFPA70E)

• Microsoft Office

• PC Maintenance

• Lathe and Milling

• Welding (SMAW,TIG, MIG)

• English and Spanish Fluency

Manufacturing / Mechanical & Electrical Experience: Gap Inc. 3400 Gap Dr. Fresno, Ca 93727

Dates: 01/2019- Present Title: Maintenance Mechanic III Duties:

• Lead, develop, and train team of maintenance technicians.

• Enforcing safety practices and ensure team members adhere to all safety guidelines and procedures and are current with all safety requirements such as: LOTO, conveyor safety, proper PM procedures.

• Assist in development of preventative and predictive maintenance on critical paths. Insure work orders are recorded in CMMS system and coordinate maintenance assignments (PMs and Special Projects.)

• Trained mechanics when necessary during repairs and helped troubleshoot electrical equipment (PLC’s, Motors, Transformers and VFD’s, etc.), inspected work performed.

• Work with ASRS (automated sorting and retrieval systems. TGW cranes, shuttles, Beecher transplant and Euro sorter.

• Maintaining and repairing conveyors.

• Troubleshoot electrical problems related to relay logic, ladder diagrams, and control components (photo eyes, motor starters, relays, limit switches, servo drives, motors, etc.

• Use assembly drawings, P&ID’s and manuals to tune equipment for operation and repair, use electrical

(VFD’s, motor starters) and logic (PLC) principles to solve equipment problems. Baltimore Air Coil 15341 Rd. 28 1/2 Madera, Ca 93638 Dates: 03/2018- 01/2019 Title: Lead Electrician Technician Duties:

• Wire and work with three phase and single phase electrical circuits 24 VDC to 460 VAC.

• Wire three phase motors 200 volt- 480 volt loads, transformers 24volt-480volt, switches, sensors and transmitters.

• Program Logic controls using MTU’s and RTU’s, logic gates programing and changed parameters.

• Read and interpret blueprints, electrical and electronic circuit diagrams and schematics.

• Hi-Pot (dielectric) tested

• Troubleshooting and obtaining precision measurements and system readings using electronic measuring

(Voltage Ohm Meter and Digital Multi Meter).

• Calibrate equipment to required signal volt, mA or psi.

• Made service calls, talked to customers, contractors, field technician through troubleshooting. Mission Foods 2849 E. Edgar Ave Fresno, CA 93706

Dates: 12/2017 to 03/2018 Title: Maintenance Supervisor Duties:

• Coordinated maintenance assignments, hours, overtime, ensured preventive maintenance program followed and communicated across departments and shift to determined conditions and operations priorities.

• Trained leads and mechanics when necessary during repairs and helped troubleshoot electrical equipment

(PLC’s, Motors, Transformers and VFD’s, etc.), inspected work performed.

• Located sources of problems by observing mechanical devices in operation.

• Performing root cause analysis using analyze 5 why’s technique of the six sigma.

• Lead and supported projects as assigned related to continuous improvement, quality, safety, or cost reduction.

• Provide leadership (supervision, guidance and coaching, training and technical support) to maintenance team members. Conduct performance reviews, reinforce performance expectations, and issue progressive disciplinary actions as needed.

Baltimore Air Coil 15341 Rd. 28 1/2 Madera, Ca 93638 Dates: 03/2017- 12/2017 Title: Lead Electrician Technician Duties:

• Performed electrical work wiring, troubleshooting, running conduit and calibrated equipment.

Thiele Technologies 1949 E. Manning Ave Reedley, Ca 93654 Dates: 02/2015- 03/2017 Title: Mechanical/ Electrical Technician Duties:

• Reviewed instructions, blueprints, schematics, and diagrams for automation machinery constructed and assembled new or modified rebuild machines.

• Located sources of problems by observing mechanical devices in operation, listening for problems, and resolving assembly problems.

• Installed wiring and other electrical components.

• Implemented Lean Manufacturing practices (Muda, Kaizen, and Kanban). Adco Mfg. 2170 Academy Ave. Sanger, Ca 93765

Dates: 06/05 to 06/07 Title: Mechanical/ Electrical Technician Duties:

• Installed gearboxes, motors, pneumatics, and troubleshot for potential equipment problems on new or rebuild machines per company or customer specifications.

• Troubleshot and obtained precision measurements and system readings using electronic measuring tools

(VOM and DMM).

• Read and worked with schematics, wiring diagrams and installed wiring, motors and other electrical components.

Certificates and Education:

Fresno City College 06/2015 – Present 1101 University Ave. Fresno, Ca 93741

• Industrial Controls Technician Certificate Fresno City College 2018

• Electrical Safety NFPA70E Fresno City College 2018

• Electrical Systems Technologies Certificate Fresno City College 2019

• FANUC Industrial Robotics Certification Fresno City College 2019

• Photovoltaics Fresno City College 2019

• Maintenance Technician Certificate In Progress

Contact this candidate