Engineer Electrical

Sarai R. Roth 941-***-**** (Cell)

**** ********* **. *******, ** 77036 ***************@*****.***

Page 1 of 3

PROFESSIONAL PROFILE:

Experienced Hardware Engineer possessing exceptional ability for attention to detail while multitasking which allows me to implement new designs and current or new technologies at a faster pace and cheaper cost, providing results and solutions faster. Experienced in working on Extensive use of software debugger, logic analyzer, and oscilloscope, In Circuit Emulators, Multi-meters, and protocol analyzers, spectrum analyzers, other test equipment for product development, failure analysis, trouble shooting, and verification testing of Systems, and Hardware. Good knowledge of microcontrollers (ARM, Texas Instruments), IC interfaces (SPI, I2C). EXPERIENCE:

ACN IBO: Concord, NC October 2017 - Current

Executive Team Leader

• Develop and monitor project budgets to assure the organization is effective and efficiency.

• Develop processes to ensure delivery of a timely and high-quality service.

• Coordinate the annual budget and planning process and oversee long term budgeting and goals.

• Direct and conduct training the new team member to better understanding the system of the organization.

• Mentoring and coaching new team member about the vision of the organization so they can achieve the highest level of excellency.

• Consulting Independent Business Owners how they can grow their organization and servicing others.

CAE Healthcare: Sarasota, FL October 2011 – December 2016 Manufacture Hardware Engineer II

• Developed process flow charts for incoming and outgoing inspection of new products.

• Trained Technicians how to trouble shooting DC convertors, Power Controller boards and other advance boards.

• Trained the Technicians to trouble shooting advance circuitry boards (motherboards) using RS232, JTAG and LAN.

• Developed quality continuous improvement on our current products by exercising Six Sigma.

• Data collecting and using DMAIC method to improve quality products.

• Reviewed and implementing drawing changes on current and existing product lines.

• Created and trained matrix as well as mentoring Senior Technicians for better understanding of test procedures and flow charts.

• Managed and lead the Quality team to launch new products using DFEMA and PFEMA.

• Consulted with suppliers and implement quality improvement on current components as well as new components.

• Created and follow up with Supplier Corrective Actions and created process to detect failures prior to introducing the components/sub-assemblies to the assembly lines.

• Supported production teams and the production technicians with complex electronic and pneumatic issues to reduce production down time.

Sarai R. Roth 941-***-**** (Cell)

7255 Corporate Dr. Houston, TX 77036 ***************@*****.*** Page 2 of 3

• Create and develop process and work instructions for Production Assemblers.

• Lead the New Product Development Team to launch new products and lead the statistical process control team to minimize waste.

• Lead the Kaizen Team to increase quality of our products and increase first pass yield.

• Create hardware versioning application to write version, serial number, and assembly numbers to I2C EEPROM, I2C real-time clocks, I2C temperature sensors.

• Fully utilized I2C, SPI, SCI, ADC's, PWM peripherals on the DSP.

• Have an in depth understanding of Low Power Modes and the hardware and software required to meet power budgets.

Gentex Corporation: Zeeland, MI March 2005 – August 2010 Embedded Software Test Engineer

• Supported Software Test Engineers in the execution of software test plans to meet product requirements for software function per customer’s specifications.

• Supported Software Test Engineers in the coordination with Electrical Systems integration of customer software to hardware for final product function, validation, and launch.

• Interfaced with Mechanical Engineers, Microelectronics Assembly, Electronics Assembly, Final Assembly, Applied Materials, and Quality Departments to support the execution of Electrical Engineering products into applications.

• Validation of our Electrochromic Dimming Rear View Mirror (NVS) microphones and speakers along with RF transmission Testing per OEM specifications.

• Programmed Agilent Data to capture outputs of the Microprocess (CPU) in various temperature conditions.

Gentex Corporation: Zeeland April 2000 – March 2005 QA Validation Engineer

• Recorded data and reported data with passed and failed to our clients. Provided resolutions before launching new products.

• Performed testing and prepared test reports according to OEM specifications, ISO, and SAE requirements.

• Developed and maintained test equipment to validate products to OEM specification requirements.

• Certified to setup Vibration Test Equipment in a Control Test Chamber.

• Proficient with smart relay, Agilent data logger, programmable power supply, Torque Test Equipment and Head Form/Impact Test Equipment.

• Troubleshoot and repaired circuitry on automatic dimming mirrors (NVS) to the component level.

• The ability to read and understand complex electrical schematics and mechanical drawings.

• Worked closely with Engineers to ensure the electrical design and mechanical design is appropriate for the project/product design approach.

• Troubleshoot test equipment such as a combo tester used to program microprocessor.

• Worked closely with Engineers to find the root cause and repaired them to eliminate down time.

• Facilitated production team members and lead them to accomplish our production daily goal.

Sarai R. Roth 941-***-**** (Cell)

7255 Corporate Dr. Houston, TX 77036 ***************@*****.*** Page 3 of 3

Gentex Corporation: Zeeland, MI June 1998 – April 2000 Competitive Analysis Technician

• Validated Competitor’s products and wrote test procedures according to the customer’s specifications. Reverse engineered competitor’s products circuitry and benchmarked Competitor’s products.

• Created part lists and evaluated the cost to manufacture the Competitor’s products.

• Developed and created document to support the finding of our Competitor’s products and working the Legal department to ensure that our competitors are not infringing with our patent.

• Created schematics of our Competitor’s products and cost evaluation of their products.

• Designed equipment and test setup to validate our competitor’s product in cross reference to our products.

• Created and prepared report quarterly to brief Managements, Legal Department and the Founder of the company.

Gentex Corporation: Zeeland, MI December 1997 – June 1998 Manufacturing Process Electronics Technician

• Troubleshoot and repaired circuitry on automatic dimming mirrors (NVS) to the component level.

• The ability to read and understand complex electrical schematics and mechanical drawings.

• Worked closely with Engineers to ensure the electrical design and mechanical design is appropriate for the project/product design approach.

• Troubleshoot test equipment such as a combo tester used to program microprocessor.

• Worked closely with Engineers to find the root cause and repaired them to eliminate down time.

• Facilitated production team members and lead them to accomplish our production daily goal. EDUCATION:

ITT Technical Institute, Indianapolis, IN Completion Date November 1997 Degree: Bachelor of Applied Science

Major: Electronics Engineering of Technology

Minor: C++ Programming

Member: National Vocational Honor Society

PROFESSIONAL WORKSHOPS:

Management training, Problem Solving, Doors, Certification for Vibration Equipment, Shock Equipment CANoe, LIN RS232, FPGA, Xilinx, Environmental Control Chamber, LeCroy Oscilloscope, Salt Spray, Photo Spectrometer, RF Test Equipment, Acoustics Test, ESD (Electrostatic Discharge) Allen Bradley PLC. Certification for GD&T, Lean Six Sigma Green Belt Certification, LabVIEW, Solid Works, Swift Programming Language, Python Programming language. REFERENCES AVAILABLE UPON REQUEST

Contact this candidate