Danny G. Muntean

Email: adbppw@r.postjobfree.com; Phone: 657-***-****

**** * ****** **** ** Habra, CA 90631

Objective

Seeking to obtain an Electrical EMC Engineering position. Where I can efficiently use my experience and skills to assist with EMC, EMI, Lightning testing and Environmental Testing. Education

Southern California Institute of Technology

Bachelor of Science, Electronic Engineering (Not Completed) 2010-2015 Experience

Independent Testing Laboratory, Costa Mesa, CA

October 2015 – Present

EMC/EMI Engineer

• Designed, built and tested level 5 Lightning Generator able to achieve: WF1, 2, 3a, 3b, 4, 5a, 5b and 6h. Pin Injection, Cable Injection and Ground injection. Pulse trains achieved: Single stroke, Multiple Stroke, Multiple burst and Multiple Pulse.

• Circuit design and simulation all done on LTSpice

• Sole tester for high level lightning testing

• Test RF Radiated Susceptibility up to 350V/m from 2MHz to 18GHz.

• Test RF Conducted Susceptibility at Cat Y (400ma +6dB) from 10KHz to 400MHz.

• Test RF Radiated and Emissions

• Consult customers in troubleshooting for their equipment under test – thresholding susceptibility tests and sniffing and real time troubleshooting for emission testing.

• Designing an RF Reverb Chamber, able to radiate about 17,000V/m from 100MHz-6GHz Communication and Power Industry, Beverly MA

May 2015 – October 2015

RF Microwave Engineering Tech.

• RF CFA testing:

• Tuning tube amplifier cathode to optimal RF power, phase and spurious emission standards. Dynamic Impedance with high Voltage and Current. Hypot testing. Time Delayed Jitter, MTI Noise and Clutter testing. Responsible for All RF Testing for CFA.

• Measuring Cathode positioning of CFA’s

The Boeing Company. El Segundo, CA

December 2013 – May 2015

Microwave RF Technician

• RF testing including; RF Emissions and susceptibility testing, Return Loss testing, Isolation, RF leakage testing, PIM testing, Thermal Chamber testing, Antenna Pattern, Antenna Row Testing, Benchtop Antenna Range, Dent tuning. (All RF testing on Antenna of satellite).

• Built flight hardware from passive antenna components to antenna feed build-ups, waveguide installations with PIM shims, bonding flight hardware according to print and planning.

•Reviewed data and determined if data is acceptable to pass on to Systems Engineering.

•Troubleshoot when antenna or RF test is failing.

DNB Engineering, Inc. Fullerton, CA

June 2010 – November 2013

EMC/EMI Test Engineer and Indirect Lightning Induced Susceptibility Generator Assembler

• Test RF Susceptibility and Emissions from HF – Ka band (low and high power)

• Test all 21 sections of RTCA DO-160 revisions C through G

• Test section 22 and 25 RTCA DO-160 Indirect and Direct Lightning Induced Susceptibility

• Test MIL – STD 461F and MIL – STD 462 (all sections).

• Consult customers in troubleshooting for their equipment under test – mostly with EMPro 3D Simulation

• Build Waveform 1-4, 5a and 5b indirect lightning generators

• Test Thermal Chambers, Vacuum Chambers and Vibration plates.

• Organize lab equipment in order to improve testing efficiency Skills

• Highly skilled in Electronic/Electrical work and troubleshooting, power tool use, professional organization, documentation.

Proficient in the following programs: LTSpice, NSI, EMC Tile 4, 5, 6, and 7, EMPro 3d Electromagnetic Simulation software (Agilent)

• Proficient and highly knowledgeable in the following procedures: RCTA DO-160 C – G, MIL – STD 461 and 462, NASA and Boeing RF Test Specifications and Procedures

• Highly proficient in the use of HP Power supplies and amplifiers and all types of RF testing equipment

• Highly proficient in the use of Power Meters, Programmable Network Analyzers, Spectrum Analyzers, Antenna Probes, Diplexers, Triplexers, Oscilloscopes

Contact this candidate