Resume

Sign in

Mechanical Engineer Site

Location:
Lagos Island, Lagos, Nigeria
Salary:
2500 usd
Posted:
December 16, 2019

Contact this candidate

Resume:

CURRICULUM VITAE

KHALILULLAH AHMAD RAZA

QA/QC Mechanical Engineer

MOB NO: +919********* / +234**********

E-MAIL ID: - ada23f@r.postjobfree.com

CAREER OBJECTIVE

To gain a dynamic & challenging role in the area of Mechanical-Quality Engineer that will offer be the best opportunity for further development of my abilities skills and knowledge. To become a perfect learner, work in a team and best implementation of my knowledge gained. CURRENT EMPLOYEE

Organization : SHAPOORJI PALOONJI INTERNATIONAL

Designation : QA/QC Mechanical Engineer

Project : ADMIRALTY EVERCARE HOSPITAL (LEKKIPHASE1,LAGOS, NIGERIA) Duration : JUNE 2019 TO TILL Continue

Organization : SHARQAWI ELECTROMECHINACAL CO.

Designation : QA/QC Mechanical Engineer

Project : METRO PROJECT RIYADH

Duration : JULY 2017 TO TILL JULY 2019

Responsibilities Undertaken:-

• Conduct inspection of all HVAC Materials equipment site construction activities testing adjusting and balancing of HVAC system as per applicable Standards.

• Inspection on ducting lining insulation of the air-conditioning lines ‘system

• Prepare and implement inspection and test plan based on project specifications codes and standards – ASHRAE

• Issue nonconformance report to construction team any violation of HVAC quality standards. Ensure that corrective actions to any

• Good understanding of drawings and company quality control procedures.

• Preparing Snag List

• Listing out Pipes, Fittings, Spools and other necessary components as per requirements.

• Perform inspection / monitor the disciplines of Piping, Structural, Material, NDT Documentation and coordination with other QC. Inspectors.

• Responsible for all QC inspection activities, welding procedures, witness welder qualifications, monitor and review of consumables controls records.

• Performing HVAC materials receiving inspection such as Duct, Air Handling Units etc.

• Preparing Punch List (Pre-Test & Post-Test).

• Preparation pressure test packages and physical check of lines in accordance with P

& ID and isometric drawings.

• Inspect the FRP, GRP, RTR, and GRE U/G and above ground pipes

• Verify and ensure the calibration of instruments for Hydrostatic testing

• Inspection of Portable Water Pipe, Fire Water Pipe, Structural, Equipment & Insulation.

• Inspection of Plumbing Underground, & Aboveground piping and in process

• Coordinate for Non Destructive examination of welds (RT), pressure test in accordance with approved procedures and QC plans.

• Welding and Piping Inspection based on approved engineering drawing and layouts.

• Monitor performance of the welders on the basis of radiographic inspection and maintain reports.

• Perform visual inspection of piping, line check and prepare categorized punch list.

• Conducting visual inspection of fit-up of pipe spools during fabrication.

• Clearing the punch, check valves, elbows, flanges, gaskets etc. its Orientation, direction, schedule, rating, and size as per the drawings prior to installation.

• Inspects, using visual observation and mechanical new installations and alterations of plumbing and drainage systems in public and private buildings

• Inspection of Plumbing fixtures supplies piping and drainage piping

• Inspection of Storm Water Drainage System &Emergency Eyewash Shower System

• Inspection of Electric Water Heater

• Installation & Materials Inspection of VRF System

• Materials & Installation of Fire Pumps and Firefighting system WORK EXPERIENCE

Organization : SHARQAWI ELECTROMECHINACAL CO.

Designation : QA/QC Mechanical Engineer

Project : Sadara Chemical Company (Aramco & Dow Chemical JV) SDL Building Package A&B

Duration : May 2014 to May 2017

Job Responsibilities:

• Preparation of ITP and Method Statement in co-ordination of Site Engineer& Project Engineer and with help of specification, drawing and contract documents; checklist; etc.

• Preparing Punch List (Pre-Test & Post-Test).

• Preparation pressure test packages and physical check of lines in accordance with P

& ID and isometric drawings.

• Inspect the FRP, GRP, RTR, and GRE U/G and above ground pipes

• Verify and ensure the calibration of instruments for Hydrostatic testing

• Inspection of Portable Water Pipe, Fire Water Pipe, Structural, Equipment & Insulation.

• Inspection of Plumbing Underground, & Aboveground piping and in process

• . Monitoring and Inspecting the prefabrication works by the subcontractors including the inspection of incoming materials, material handling, heat number transfer, fit-up, welding activities, PWHT of welding joints, Hardness test, PMI, orientation and flush grinding of Orifice Flanges.

• Inspection and monitoring of underground GRP/FRP lines installation for drain lines, cooling water lines, fire water lines, potable water lines Etc.

• Prior to installation of U/G GRP lines, checking pipe bedding, coating/wrapping, surface preparation if any and defective material shall be discarded

• Inspection of Glass reinforced pipes storage facilities upon the request for material

• Inspection. Witnessing barcol hardness test and vacuum test for the installed GRP pipe lines

• Carrying out Inspection activities in accordance with Inspection and Test Plan

• Responsible for daily site inspection with Consultants.

• Responsible for MIR issuance, maintaining log & visiting store with Consultant for permanent material inspection.

• Assisting and coordinating with Project Manager for quality related matter.

• Following up with consultant snags and internal snags with the site engineer and maintain the log; Consultants NCR, Deficiency Notices to close it as soon as possible.

• Ensuring all testing instruments are standardized and calibrated. Maintaining log for the same.

• Responsible for incoming raw Materials’ Inspection. like Pipes, Pipe fittings, flanges, equipment’s instruments etc. and correlating with the mill test certificate, dimensional checks, condition of materials, documenting and reporting of non-conformity (if any ) to specification. And Preparation of MIR.

Organization : VASAVI POWER SERVICES Pvt. Ltd

Designation : Mechanical QC Engineer

Project : 500*2 MW CSTPS Chandrapur (M.S)

Duration : April 2013 to April 2014

Job Responsibilities:

• Preparation of ITP and Method Statement in co-ordination of Site Engineer& Project Engineer and with help of specification, drawing and contract documents; checklist; etc.

• Responsible for daily site inspection with Consultants.

• Responsible for MIR issuance, maintaining log & visiting store with Consultant for permanent material inspection.

• Assisting and coordinating with Project Manager for quality related matter.

• Following up with consultant snags and internal snags with the site engineer and maintain the log; Consultants NCR, Deficiency Notices to close it as soon as possible.

• Ensuring all testing instruments are standardized and calibrated. Maintaining log for the same.

Organization : POWER MECH PROJECTS LIMITED

Designation : Mechanical Site Engineer

Project : 2*660 MW STAGE 2 NTPC, BARH, PATNA

Duration : March 2012 to February 2013

Job Responsibilities:

• Active participate in fabrication as well as erection of spool.

• Responsible for Execution and Inspection of piping works as per ASME B 31.3

• Spearheading in stage wise fit up, dimensional checks, weld visual inspection.

• Prepare B.O.M as per planning of work.

• Provide piping input to process piping and instrumentation diagrams (P&ID) including piping classes, valve types, piping isometrics, support details.

• Mechanical Clearance of the Piping system (CS, SS,) by referring the engineering standards from the client.

• Coordinate for NDT activities, witnessing all field tests including hydro test (HT), Dye penetration test (DPT) &RT (Radiography Test), Pneumatic testing(PT)

• Update and monitor the schedule against the progress of work.

• Prepare the final documentation according to the customer requirement

• Co-ordination with Site, and Client regarding site activities. EDUCATION & PROFESSIONAL QUALIFICATION

Diploma Mechanical Engineering (DME) From K.D.K College of Engineering Nagpur, Maharashtra State Board of Technical Education.

Matriculation From Co Operative High School Ahiyapur, B.S.E.B, PATNA TECHANICAL PROFICIENCY

PROFICIENT IN: - Pipe thickness calculation, Valve Data Sheet.

Brief concept of Isometric, Bulk MTO, Pipe Rack Width Calculation, Control Station, Miter Bend, Utility Station, Plot Plan, Equipment Layout. Pump Suction Discharge Line

Familiar with, P& ID, Line List, RF Pad, PT-Rating, Code & Standard, ASTM NO. STRENGTHS

Self-confidence, positive mental attitude & Creative.

Ability to manage multiple tasks simultaneously.

Team worker and flair to learn new things.

SOFTWARE SKILLS

FAMILIAR WITH :- Auto Cad

Better concept of MS office and operating system(window, xp) PERSONAL DETAIL

Name : KHALILULLAH AHMAD RAZA

Father’s name : HABIBULLAH AHMAD

Date of Birth : 08

th

DEC, 1989

Passport Details : K1347042 Expiry Date: 27-11-2021 Gender : Male

Marital Status : Married

Nationality : Indian

Language Skill : English, Hindi, & Urdu, Arabic

HOBBIES

Playing cricket & Surfing Internet

DECLARATION

I solemnly affirm and declare that the above given information is true and correct to the best of my knowledge and nothing has been concealed by me

.KHALILULLAH AHMAD RAZA



Contact this candidate