General Education Real Estate

RESUME

Name: Suong Doan /Sylvia Doan, Phone Contact: 408-***-****

Mailing Address: PO Box 51480. San Jose, CA 95151

Email Address: ad5v2b@r.postjobfree.com, ad5v2b@r.postjobfree.com

JOB SEEKING

•Assembly and Subassembly, Test Operator

GENERAL EDUCATION

•Evergreen Valley College, San Jose City College (1990-1985): General Education, Accounting Finance, Computer Engineering

•San Jose State University, San Jose, CA (1986-1989 ): A few courses in Circuits, Heat transfer, C++

•Computer Training Academy, San Jose, CA (02/2001-11/2010) : Computer Hardware and Software Application, installation, IT, Office Application: (8 years Real estate Association)

SKILLS AND EXPERIENCES

•Sanmina Company (Coast Personnel Services), San Jose, CA 95134

04/ 2019 - 07/ 2022

Test Debug Technician ( 2nd shift): Under Engineering procedures, Medical products, Test and Fix Problems, Apply Test Software (GeneXpert Configuration, GeneXpert System, GeneXpert Thermal, GeneXpert BFL Calibration GX Optical Calibration) and Hardware procedures, Schematic diagram, hooked up Test Network equipment, computer printing traveler, order part supplies, Test and Debug Modules, Configuration, Upload Software/ Firmware, use GX module test: Included Q.C 6 and 10 color Filters/ Mirrors, test Excite/ Detect and I-Core, Troubleshoot Problems, Solved Optical and I-Core and Module problems, Test Modules, used screen C and C ++, scripting the solving results.

•Tesla Company (Advantage Resourcing), Fremont, CA 94538

10/ 2018- 12/ 2019

Production Operator: Learned functions to operate the automatic robotic machines and Run Robotic machines, Run Robotic Painting machine. Report data

•Velodyne LiDIAR Company (Kelly Services), San Jose, CA 95138

04/ 2016 - 08/ 2019

Production Test Operator: Rotor/Sensor for auto, Detector Alignment, test and troubleshoot for Rotor/ Sensor VLS128/ VLS32 product (Rotor/Sensor), used Detector Alignment VLS 128/ VLS 32, Zoom Robotic machine, read procedures, program and setup program in computer with test tool and machine, used Test interfaces, Calibration, Flex cable connection for the test station, adhesive glue process, use interface for voltage ranges, test laser target with mirror, use both manual / Auto pick-n-place the stubby, Alignment focus, find laser beam with the scope, Dip test pressure, troubleshooting problems occurred, collect accurate data and report, apply safety standard. Understand Procedures, experienced both Manual and machines, Lab tools for both Manual and Machine, Knowledge about Programing and set up Test Station, Test Network, applied interfaces, Calibration and Configuration test, apply hardware, Software, in the Management Information System, Report Data

•Gemfire Company (Now is Tesla), Fremont, CA 94538

01/ 2008 - 11/ 2009

General Lab Technician: Build fixture, used microscope, Made inductors for mother board, Packaging small PC board, test small crystal bench of inductor, fiber alignment on automation screen, temperature vacuum test, thermal test, Percentage Heat loss, photo the defected crystal beds by software to record in computer, Test light source (Get Percentage loss of light travel source), use test station with computer with Electronic probes, calibration, lab hook up equipment, alignment technique, software application, to test crystal bed, record accurate percent loss data and report. Cable connection for lab Equipment: Test Fixtures, Spectrum Analyzer, Oscilloscope, Signal Generator, Applied Computer software, Used Photo Software Zoom to Inspect in computer, traveled to other lab to delivery product sample, collected data, report data.

•Intel Corporation (Kelly Services), Santa Clara/ Newark, CA 94560

01/ 2005 - 11/ 2006

F&K 4501 Programmer ( 2nd Shift): Electronic Manufacturing Services, component product of Circuit board, QA, Test and Load Program for F&K 4501 Epoxy/ Eutectic for Eutectic F&K 4501, Loading Programin computer, Setup Test station and machine temperature, Performed Statistic Engineering Test under measurement microscope to set up machine, statistic test for solder on microscope measurement, prepared Wafer Fab, completed by machine with Pick-n-Place with robotic system, QC substrate under microscope and reworked by solder, needle, and hot plate, report accurate data, Set up Load program Test Station, temperature test, Test and program F&K 4501 Epoxy/ Eutectic Die Bonder of Intel, Q.C and fix problems, report data

•AT&T Corporation (Sykes Enterprise), Pleasanton, CA 94538

02/ 2002- 04/ 2002

Computer Training Academy, Premise Technician: Phone software application, technical support switch line state-State service, problems solving technical problem tickets.

•Anritsu Company (TAC Professional Staffing Services), Morgan Hill, CA 95037

01/ 1994- 04/ 1996

Manufacture Production: Attached components on thin film for cable Network Package, Used microscope.

•Northern Telecom (American Technical), Santa Clara, CA 95054

01/ 1993- 05/ 1994

Manufacture Production: Loading component for PCB, inventory.

•Solectron (Golden West Temporary), Milpitas, CA 95035

01/ 1991- 06/ 1993

Manufacture Production: Quality Control, Touch Up, Rework PCB, Alignment RAM/ROM, chips, SMT, components, microprocessor, Microchip, QC, Touch Up, Rework PCB, attach wires into the PC board, knowledgeable about circuits, blueprints, diagram, familiar with lab hand tools, used microscope.

•Excelsior Inc, San Jose, CA 95035

07/ 1998- 01/ 1991

Was trained in Manufacture Production: Loading Components, run PCB operator machine, warehouse inventory.

Contact this candidate