Assembler
Resume:
Debra Carter
Computer assembler, Computer tech - Applied Materials, Tesla Giga Texas
Austin, TX 78758
*************@*****.***
Authorized to work in the US for any employer
Work Experience
Computer assembler, Computer tech
Applied Materials - Austin, TX
October 2012 to Present
Proficiency developed through job-related training and considerable on-the-job experience. Completes work with a limited degree of supervision. Can act as an informal resource for colleagues with less experience.
Key Responsibilities
Able to perform a wide variety of routine and non-routine electro-mechanical assembly operations along troubleshooting and repair. Adjusts, aligns and/or performs "go-no go" tests using test fixtures or non- diagnostic electronic testing devices. Proficient in identifying and correcting errors, retesting and able to validate design fabrication and setup of assemblies. Areas of expertise: include electrical interconnect, mechanical, pneumatic, fluid flow, or vacuum technologies. Without supervision, make up set-ups, alignments and adjustments, maintaining tolerance according to instructions. Disassembles, modifies, reworks, refurbishes, reassembles and tests units as required. Follows work orders, schematics, wiring diagrams, engineering specifications, sketches, assembly shop and production operations sheets, parts and wire lists, written and/or verbal instructions to construct electro-mechanical, vacuum and/or pneumatic assemblies, subassemblies and components. Maintains a secure, safe, and healthy work environment. Attends required health and safety training, and follows safety and security policies, procedures and practices. Promptly reports accidents, injuries, safety hazards, or emergencies to supervisor or Safety department. Follows operating instructions, uses protective equipment when required, and uses equipment and materials properly. Actively strives to prevent accidents and injuries. Quality Inspector/Production
Tesla giga Texas - Austin, TX
September 2021 to February 2024
I worked in Castings, the beginning of the line making cars, I started out at Production floor working varies jobs from working in the castings, i would stand at the die machines, inspecting the front under body of car, using lift to put on the racks, i would be on the ignitions putting in the defects and depending on damage we would either scrap them out or pass them to the racks, I would work at Plasma next door to Castings, Plasma would cut the access off and we would again inspect the car for one last push to BIW, And there the process would start the making of the car. Then i was in another role, repair tech/ quality tech, I would walk around randomly checking for any defects that may of been missed, I would do repairs, not much.. i would do a pass down after my shift ended meaning i would let the next shift know basically where i left off, and what was going on during the day of defects, things to watch out for. I printed out quality alerts deviations and acknowledged the team to watch out for. I would sometimes jump on fork lift and help out team to rid of scrapes, take to scrap yard. I was forklift certified. i didn't do to much of that, we had certified fork lift drivers but, just incase i would jump on one. and that's bascially my job at Tesla giga Texas.
Wafer Fab Operator
Samsung Semicondutor - Austin, TX
February 2008 to June 2010
I would get a Lot of 25 wafers, put them through the assigning tool making sure they processed take them out and send them on to the next processing stage. Sometimes I would run a cart of Lots to other departments.
Freescale semiconductor, Austin, Texas
Cleaning room, Aug 2010 - Dec 2012
I worked in various stations, working with Lots of wafers. The lots would be assigned to the area I would take the lots and run them though tools, tools that would clean and scrub the wafers, take them out the tool send them off to the next station. If the tools needed to be cleaned for particle change then I would process a qual for particle damage, run it though the tool and measure the wafer if it was particle free, if okay then i would continue loading lots onto the tool. Computer Tech
Dell Computer
August 2003 to December 2007
I would work on Refurbished laptops, desktops, making sure they were able to sell again, If that meant ordering parts for no video, bad dimms, etc. I would replace them and do a quick test to make sure the system was in good standing for it to be shipped out. Computer assembler, Computer tech
Dell Computer - Austin, TX
December 1998 to December 2007
Worked on assembly line, installing motherboards, CPU, Dimms, Hard Drives, modems etc. I was an inspector; my duty was to make sure that the order was to the customer's satisfaction, Skills
• Assembly
• Manufacturing
• Mechanical knowledge
• English
Additional Information
• I also was promoted to Computer Tech at Dell computer, where i worked on refurbished laptop, desktop, I would replace memory if needed, etc. ordered parts that i needed to get the system back to top shape., I quick tested the systems making sure they went well though the process.
• I also worked at a cleaning room at Samsung.
Contact this candidate