Electrical Service

DILLON LAVERNE HUTTO

Augusta GA • 803-***-**** • ***********@*****.***

Electrical Apprentice

****-** - ****-** *.E.D.

Barnwell High School

****-** - ****-** ******** County Career Center

Electricity 1 and 2

2010-08 - 2011-06 Orangeburg Calhoun Technical College My second year of electricity was college credit for two classes which were introduction to the NEC and introduction to blueprints. After completion of these two classes there was a test to take. I passed and a nccer certification card was issued to me.

2016-11 - 2016-12 Electrical Apprentice

Augusta Industrial Electric

I started off at a warehouse for overhead doors, where they would take golf carts and maintain them. I ran half inch and three quarter pipe for receptacles and lighting. I terminated panels and even ran pipe for a automatic gate. From here I went to work at keloggs, where we were to do a shutdown at the plant. What was called the mixer project I cut bent three quarter rigid pipe that ran from silo to silo in what were essentially the mixing silos. I also took responsibility to be in a room called the boiler room, where the tempature stayed above at least 100 degrees so the oil inside the tanks did not harden up. There were four silos that had to have devices on each wire pulled to each. Each had to be terminated. The devices on the silo checked different levels of a variety of ingredients for the proper mixture they wanted. I had an OSHA 10 already, one of Kelloggs requirements was that your osha 10 cannot be no more than three years old.

2016-05 - 2016-11 Electrical Apprentice

West Georgia Electric

I began this job at the Augusta Natiomals. This was my biggest job I've been on. Here I started out in the basement running four inch service feed and back up generator pipe. I patched the hole where these pipes left the building with concrete. On the ground level I ran mc, I wired both front and back porchs, I ran emergency circuits feeds, terminated panels, and wired led can lights. With a short crew on a weekend we managed to pull all 24 service feeds. On the second floor I ran mc, ran pipe for HVAC units, not sleeves through concrete, core drilled on both first and second floor where some things were added or was forgotten, and wired both porches on the front and back. I also had to make small adjustments to rows and columns of can lights. Me and one other electrician fixed 220 can lights that were originally supposed to be symmetrical horizontally vertically and even diagnolly. I also wired several rooms with dimming switches and fixed others that were not wired correctly. On the roof I terminated all HVAC units which i could walk inside of ran the seal tight, as well as terminated humidifiers and exhaust fans in several areas. I was also part of the preconstruction for maintenance receptacles. 2014-12 - 2016-03 Electrical Apprentice

Electrical Communications Services

I worked in schools most of my learning here consisted of troubleshooting. There was a job that I was on here that was new construction. Here I pulled service feeds ran all mechanical pipe pulled all mechanical wiring terminated their panels and vavs as well as units. Terminated lighting panels switches and devices. Devices consisted of power packs occupancy sensors led fixtures, which was all Education

Work

History

https://www.visualcv.com/xw7orjuuho4

motion activated. Troubleshooting other schools I learned about emergency and normal power, how they only meet at relays, how a relay works according to the way it is wired, and how these relays can sense a power outage of normal power. Once power is lost, relay sense says to cut emergency power on until continuous normal power stays in affect. Only then will emergency power cut off. 2014-03 - 2014-08 Electrical Apprentice

Bryant Electrical Contractors

My first electrical job I learned a lot but could not manage to obtain everything. I started out with the demolition of a panel room on second floor. I also demolished three panel rooms on ground level as well as demolished several extra service feeds that were no longer needed. We added a switchgear which i was allowed to hook up. I terminated high voltage panel for the mechanical rack which I ran by myself with one electricians leadership. I was allowed to terminate all vavs in this building all HVAC units in this building. I even wired the dome lights in this building. Fort Discovery what is now Unisys. 2014-02 - 2014-03 Fire and Water Restoration Repair Duraclean

I cleaned up dryed out the disasters of water and fire in a home while planning to restore the home or business to its prior state.

2013-08 - 2014-02 Machining Tech. and Welder

C and G Machine and Welding

I machined a variety of parts of different metals. Used automatic lathes as well as manual lathes, used automatic mill, and even done some welding.

2013-02 - 2013-07 Tire Changer

Josh's New and Used Tires and Auto Sales

Answered phone for customers, took walk in customers, sold new and used tires, managed finances daily for this company, mounted dismounted and balanced new and used tires for customers. 2012-01 - 2013-02 Welder Pipefitter

Carroll's Heavy Metal Welding and Industrial Services I was pipefitting for reinke irrigation. I even maintenanced the jobs that we completed. Meaning if there was a leaking pipe or a pipe burst we would come and repair. I also welded trusses that were laid in semi trucks. Once laid down we secured them tacked a grate on top of and the space where the truss sat, would actually be used for blowers which dried peanuts. Mechanical knowledge

Genie and Aerial life certified

Skills

https://www.visualcv.com/xw7orjuuho4

Contact this candidate