Engineer Test
Resume:
Mohammad Mahmudul Hasan
Contact: - 316-***-****
***********@*****.***
Dallas, TX, United States 75229 CSCO12942203
Objective:
Seeking a challenging position that allows me to contribute my knowledge and experience with organization on RF engineering.
Work Experience :-
Work Experience- 5 years in Telecom Experience.
Sublime Wireless Inc.
Duration: February’2017 to present
Position: Associate RF Engineer
Responsibilities:
● Verify azimuth & height of each sector.
●Perform drive test in idle mode to log & verify coverage (BSID), signal strength (RSSI), quality
(CINR) for each sector following route plan for each sector.
●Perform functionality test (throughput, latency, HTTP etc) at points that meet defined criteria for each sector.
● Check handover.
● Start Navigation using Street Atlas for route analysis.
●Submit log files, antenna parameter verification report to analysis & optimization team.
●Perform post tuning drive test as required & submit log files to analysis & optimization team.
●LTE Drive test with corresponding analysis of RxLev, RxQual, PCI in different bands, Handovers, TCH Drops and many other events in Radio Interface using XCAL-S investigation.
● Data Analysis in e-dat Nokia Tools.
● Analysis PCI for each sector.
● Stationary and mobility test, checking throughput in different bands in LTE networks.
●QXDM professional for VoLTE test, regression, sanity test.
● SSB and Cluster data analysis.
● bCEM and Airscale migration performance comparison activities.
M&H Telecom (ICX Operator) (Bangladesh)
Duration: 06’Sep’2010 to 30’April’2012
Designation: Assistant System Engineer
I have configured routing protocol on CISCO Router OSPF, EIGRP & Static routing.
Day to Day activity configure ACL on CISCO router and take backup of Router changes,
Configure DHCP and connect New PC in Network on L2 Switch
● Firewall Monitoring ACL configuration allow traffic day to day as per client requirement
●Switch Configuration create VLAN. assign PC in VLAN.
●Monitoring routing protocol and device health ( CUP and disk Space)
●Configure ACL on CISCO firewall and take backup.
●Keeping keen observation of all the departments: Transmission, Core, Datacom & power of M&H telecom, Chittagong site.
●Observe and involve day to day operation of the exchange for smooth O&M of telecom transmission equipments like SDH high capacity MUX Huawei Optics OSN 3500, media gateway Huawei MGW8900, switching router Huawei Quidway NE40.
●Ensure proper operation of ODF, DDF, MUX of other operators at the colocation point (where different operators joins with the ICX).
●Keeping deep concentration on power system: whether the AVR, Rectifiers, Battery Banks, Generator, Power distribution boards are working properly or not. Also preparing power report weekly.
●Maintenance of interconnection service through Media Gateway (UMG8900) connections
with other operators (GSM/CDMA/PSTN).
●Reporting equipment temperature, humidity, cabinet and board status.
●Reporting alarms (critical/major/minor) of the equipments.
●Backup of the T2000 database.
● Have work on cisco 2600, 1800 & 1900 Router 3550,3560, 3650,3750 Switch
● CISCO Firewall ASA 5505, 5510 & 5512-X
Pi Technologies Limited ( ZTE Wimax Network Project)
Duration: From February’2009 to August’2010
Position: Junior RF Engineer
Wimax drive test with corresponding test/verification of Centre frequency & Preamble Index codes, coverage (BSID), signal strength (RSSI), quality (CINR), handover, throughput, loop back latency (ping), HTTP etc using XCAL-X and CNT.
●GSM Drive test with corresponding analysis of RxLev, RxQual, SQI, Handovers, TCH Drops and many other events in Radio Interface using TEMS investigation.
Project Experience
Banglalion Communication Limited RAN Optimization Project .
February-05-2009 To May-07-2010
●Verify azimuth & height of each sector.
●Perform drive test in idle mode to log & verify coverage (BSID), signal strength (RSSI), quality
(CINR) for each sector
following route plan for each sector.
●Perform functionality test (throughput, latency, HTTP etc) at points that meet defined criteria (e.g., CINR>20) for each sector.
●Check inter and intra handover in different sectors.
●Submit log files, antenna parameter verification report to analysis & optimization team.
●Perform post tuning drive test as required & submit log files to analysis & optimization team.
Master’s project : Network design using MPLS technology.
EDUCATION:
Master of Science in Engineering, Computer Network Systems
University of New Haven, Connecticut.
B.Sc. in Computer & Communication Engineering
International Islamic University Chittagong, Bangladesh.
PROFESSIONAL CERTIFICATIONS:
CCNA certified CSCO12942203
Contact this candidate