CAD EXPERIENCE: AutoCAD releases ** thru ****, Mechanical Desktop, Inventor, Solid Edge, Solidworks, Cadam, and familiar with Pro Engineer (500 hours).

EXPERIENCE:

NOV Hydra Rig, Fort Worth Tx. 4/10-9/16- Responsibilities: Design and drafting of oil well service assemblies, coiled tubing, snubbing and nitrogen recharging units. Created assembly, detail and installation drawings using AutoCAD 2d and 3D.

Techni-Power Corporation, Arlington Tx. 6/09-12/09- Responsibilities: Subcontract AutoCAD work for 2 clients in Arlington and Fort Worth Tx.

NOV Hydra Rig, Fort Worth Tx. 5/07-3/09-Responsibilities: See above.

Dosmatic USA, Carrollton Tx. 7/06-4/07-Responsibilities: Design and drafting of injection molded water driven proportioning valves, filters and related molds, tooling and assembly fixtures using Solid Edge solid assembly modeling.

Heledyne Systems Inc, Hurst Tx. 9/05-7/06 (subcontract position)-Responsibilities: Design and drafting of helicopter interior components, (stretchers, floor and wall mounts for stretchers, ventilators and other medical devices). Created assembly, detail and installation drawings using Mechanical Desktop and Autodesk Inventor 3D assembly modeling.

NOV Hydra Rig, Fort Worth Tx. 6/05-9/05 (subcontract position)-Responsibilities: See above.

Universal Punch Corporation, Santa Ana Ca. 4/04-5/05-Responsibilities: Design and drafting gauge assemblies and components, design and drafting of punches and dies for manufacture of fasteners (Torx, hex, Philips drives, etc) using mechanical desktop and Autodesk Inventor solid modeling.

Comarco Wireless Technologies, Irvine, Ca. 9/03-11/03 (subcontract position)-Responsibilities: Design and drafting of power supplies and related assembly and test fixtures using Mechanical Desktop.

Goodrich Corporation, Santa Fe Springs Ca. 7/03-9/03 (subcontract position)Responsibilities: Design and drafting of aircraft brake components and related heat treating equipment using Mechanical Desktop (contract assignment for designer out on medical leave).

Malibu Research, Calabasas, Ca. 12/02-6/03-Responsibilities: Design, drafting and electronics packaging for ground based satellite receiver dishes using Mechanical Desktop solid assembly modeling .

Alan Sublett- sheet 2

Boeing Satellite Systems, El Segundo, Ca. 2/97-6/02-Responsibilities: Design, drafting and electronics packaging, including aluminum and kovar housings and carriers for satellite receivers. Layout and production of RF and microwave circuitry using laminates, TMM and ceramic materials. Design and drafting of assembly and test fixtures for same. AutoCAD 2d and Mechanical Desktop solid modeling used for both R & D and production drawings.`

Pacific Scientific, Duarte, Ca. 9/96-2/97 (subcontract position)-Responsibilities: Design, drafting of aircraft instrumentation, hardware and fire extinguishing systems for commercial and military aircraft using AutoCAD 2d and 3D (release 13).

SJ Controls, Signal Hill, Ca. 9/94-9/96- Responsibilities: Design and drafting of piping, valves and instrumentation for automated fluid control systems, and related structural support systems and process flow diagrams for soft drink industry.

RMS Technologies, Los Angeles Ca. 10/92-5/94 (subcontract position)-Responsibilities: Design and drafting of electronic security systems involving mounting and wiring of electromechanical devices and controllers using Cadam and AutoCAD.

Loral Aeronutronic, Newport Beach, Ca. 4/91-7/92-Responsibilities: Design and drafting of detail, assembly and schematic drawings for missile guidance control systems In accordance with ANSI – Y14.5. Maintained Army and Air Force programs such as AIM 9R, Sidewinder and Chaparral missile guidance systems. Had secret clearance.

Kaiser Electroprecision, Irvine, Ca. 6/89-3/91-Responsibilities: Design and drafting of aircraft fuel level measuring assemblies, various composite components and related molds and tooling.

Amtec Engineering, Brea, Ca. 8/85-6/89-Responsibilities: Mechanical drafting and design for various companies as contractor.

SII Dyna Drill, Irvine, Ca. 1/80-8/85-Responsibilities: Drafting and design of down-hole drilling motors, related tooling, assembly and test fixtures.

Education:

Certificate in Dimensioning, Tolerancing, Descriptive Geometry, Algebra and Trigonometry –

National Business Institue, Riverside Ca.

Micro Cadam, AutoCAD, Irvine Valley College, Irvine Ca.

Drill Rig Technology, SII Smith Tool, Irvine, Ca.

Hydraulic systems Theory and Operation, Paul Monroe Hydraulics, Rose Hills Ca.

Intro to Catia, El Camino College, Torrance, Ca.

Intro to Pro Engineer, Parametric Technologies, Los Angeles, Ca.

Intro to Solidworks, Texas engineering Systems, Carrollton, Texas.

Contact this candidate