ROWELL DELA PENA PATRICIO
Mobile number: +974-********
Email: acwu2z@r.postjobfree.com
Address: Al Rufaa Area, Old Salata Doha, Qatar
Nationality: Philippines
DOB: March 03, 1983
Gender: Male
CAREER OBJECTIVE
Looking for a challenging career to show the best of my professional abilities, skills and techniques to enhance my knowledge and growth in Electronics, Telecommunications and Electrical industries.
PRE QUALIFICATIONS
I am a 5-year Bachelor of Science in Electronics and Communications Engineering graduate, who has an experience in electrical jobs and motor control operation. I am equipped with expertise and skills such as installation, troubleshooting, repairing and maintenance.
WORK EXPERIENCE
Electrical Sub-Contractor (Camella Homes A Vista Land Company) April 2012–August2016
Cauayan City, Isabela, Philippines
Duties:
- Read blueprints and technical diagrams of electrical plans
- Follow local building regulations base on the National Electric Code
- Perform cutting, bending and treading electrical conduit
- Installation of utility and junction boxes, imbedded in walls, partitions and ceilings
- Installation of electrical wiring,power outlets, controls, lighting fixtures, CATV signal outlet and telephone modular jack
- Install electrical components such as circuit breakers, service entrance and meters
- Identify any electrical problems with the use of hand tools and testing devices (Volt Ohm Meter)
- Repair and replace damage wiring, circuit breakers and fixtures using hand and power tools
- Ensure the electrical system works properly to prevent future faults
Motor Control Center Technician (San Miguel Incorporation, BMeg) Sept. 2009 – April 2012
Echague, Isabela, Philippines
Duties:
- Proper operation in corn drying, corn shelling, final drying and bagging, with the use of Siemens Programmable Logic Controller (PLC), manual and automatic mode
- Preventive maintenance on motors controls:
Cleanliness, blow out dirt weekly
Moving parts inspection, it should operate easily without excessive friction
Contact inspection for pitting and signs of overheating can be notice by odor and discoloration of metal
Perform contact resistance testing with a low-resistance ohmmeter
Overload relay inspection, check proper setting of trip
- Maintenance of facility equipment such as 3 phase motors, centrifugal blowers and fan, biomass heaters(used to dry the shelled)
- Maintain conveyor belts to flow normally to prevent delay
- Complete manning on respective areas to continue a smooth flow of operation
SHORT COURSE TRAINING
Electrical Installation and Maintenance, National Certificate II
Issued by: TESDA-Technical Education and Skills Development Authority
Ilagan City, Isabela, Philippines
Date issued: March 28, 2015
Consumer Electronics Servicing, National Certificate II
Issued by: TESDA-Technical Education and Skills Development Authority
Ilagan City, Isabela, Philippines
Date issued: March 1, 2015
CERTIFICATIONS
Introduction to PLC Technology Using Siemens Logic Module
Issued by: Nueva Vizcaya State University, Bambang Campus
Bambang, Nueva Vizcaya, Philippines
Date issued: February 23, 2008
Trends and Innovation in the Electronic Industry and ECE Updates-IRR of RA 9292
Issued by: Patria Sable Corpus College
Santiago City Isabela Philippines
Date Issued: August 18, 2007
EDUCATION
Bachelor of Science in Electronics and Communications Engineering
Patria Sable Corpus College
Santiago City, Isabela, Philippines
June 2003 – April 2008
TECHNICAL SKILLS
Electrical design, installation and maintenance:
Design and draw electrical plans using symbols
Perform calculations of electrical loads
Prepare electrical power and hydraulic tools
Perform roughing-in activities for communication and distribution systems
Install wiring devices for floors and ground fault interrupting outlets
Install electrical protection for lighting and grounding
Install electrical lighting system on auxiliary outlets and lighting fixtures
Installation of power protection system against circuit overloads such as fuse and circuit breakers
Electronics technician:
Read and interpret schematic diagrams
Use hand tools such as (VOM) volt ohm meter, soldering iron, pliers, wire striper, screw drivers
Menstruation and calculation of rated resistance, voltage and power
Interpret technical drawing like printed circuit board (PCB) and electronic circuit symbols
Read and interpret color coding in resistors and capacitors
Terminate and connect electrical wiring and electronic circuits
Replacement of damage electronic devices
Assemble and disassemble electronic components and parts
Repair electronically controlled and domestic appliances
Repair audio/video products
IT SKILLS
Microsoft office application
MS word, MS excel, MS Powerpoint
Software installation
Hardware maintenance
CCTV installation and maintenance
LANGUAGES
English, Tagalog