knowledge in pneumatic hydraulic, and airconditioning

Reginaldy M. Carlos Mariano

*** **** *** **** ***. 3 #06-314 Singapore 680286

Contact No.: +639*********

E-mail Address: *.*************@*****.***.**

Blk. 16 Lot 2 Teachers Village G.M.A., Cavite, Philippines

SUMMARY OF QUALIFICATION:

Ten (10) years of extensive experience in the field of injection molding company as a technician or technical support. Can handle machines like JSW, KAWAGUCHI, FANUC, TOSHIBA, JETMASTER AND NISSIE.

Company : Saudi Factory for Plastic Product

Position : Maintenance Engineer

(Nov. 27, 2013 – Dec. 22, 2015)

“New Factory”

Coordinate to the head in charge about the machine and the thing to do in the factory.

Request for the tools and materials needed to be use in production and fabrication.

Electrical installation and mounting of two extrusion machines and three injection machines.

Installation of cooling tower and underground water tank.

Trial of all new molds that arrived on plant.

Trial and operate molds and machines for preparation of mass production.

Request of manpower and assign them in their respective position.

Troubleshoots, check, clean, dis-assemble, and assemble moulds if problem encountered.

Checking and troubleshooting of machine if problem encountered.

Report to the head in-charge or manager in case of major machine trouble.

Company : K&K Molding

Position : Maintenance Engineer

(March 2012 – August 2013)

Daily, weekly, and monthly checking and record of facilities and equipment of company premises and production machines and auxiliary equipment.

Performs preventive maintenance of machines and equipment in the production area.

Support the production section in problem troubleshooting encountered in the machines and its auxiliary equipment.

Knowledgeable in PLC machines and board replacement.

Report to the Assistant Manager in case of major trouble encountered in the production.

Company : Trendy Plastic Manufacturing Inc.

Position : Production Controller

(April 2008 – April 2009)

Responsible for all incoming and outgoing resin materials used in the production.

Conducting monthly inventory of parts and resin materials.

Responsible for all controlled and uncontrolled documents used in the production.

Responsible for the review of the newly revised documents.

Making Work Instructions, Condition Guide, and Operation Guide of the newly arrived parts.

Controls and monitor of the Daily Production Report (D.P.R.) and encoding of produced parts, Good’s and N.G.’s.

Making the Monthly Report of the production.

Safety Officer

Conduct awareness programs and meetings for all company employee

Monitoring and evaluation of all fire preventive devices such as fire extinguisher, fire hose/hydrant, smoke detectors, and emergency lights.

Making manual for the devices on how to use it and post it near the devices.

Conduct meeting and making corrective actions on how the near miss happened in the company.

Provide PPE (Personal Protective Equipment) to the employees.

Company : Big Philippines Corporation

(Engineering Plastic)

Position : Production Technician

(April 2003 – May 2008)

Reporting to the assistant supervisor or to the supervisor in case of major problem encountered in the machines.

Line monitoring and supervision.

Responsible for mould setting and centering.

Material, Hopper Dryer and Mould Temperature Controller checking and setting before Parameter Set-up.

First Molding Process and parameter adjustment for product dimension and appearance.

Inspection and cleaning of machines and robot operation.

Troubleshooting of Injection Machines, Robots, M.T.C., Hopper Dryer, and Barrel Heater.

Monitoring of all activities with in the shift and machine output and efficiency.

Start-up and Shut down of machines.

Position : Production Die - Setter

(September 2002 – April 2003)

Responsible for mold searching and setting.

Setting and centering of mold in the injection machine.

Testing of mold opening, closing and mold temperature controller setting based on mold parameter before turn over to the line technician in-charge.

Turn over of mold to tooling section after production.

Fundamentals of Lubrication and Hydraulics March 20, 2009

ISO 9001:2008 / ISO 14001:2004

(Conducting Effective Integrated Management System Internal Audit) February 10-11, 2009

Hydraulic Lubrication and Storage Handling January 23, 2009

Understanding Environmental Management System

and ISO14001: 2004 August 13, 2008

ISO14001: 2004 (Top Management Briefing) July 29, 2008

Basic Occupational Safety and Health July14-18, 2008

First Aid Training August 27-Sept. 1, 2007

Basic Life Support (C.P.R.) August 27-Sept. 1, 2007

Motors, Motor Circuit and Controllers September 2000

Preventive Maintenance of Electrical Equipment September 2000

Air Conditioning and Refrigerating Equipment September 2000

College : Bachelor of Science in Electrical Engineering

Polytechnic University of the Philippines (Sta. Mesa Manila)

1996-2001

Secondary : Marcopper High School

Sta. Cruz, Marinduque

1992-1996

Elementary : Marcopper Elementary School

Sta. Cruz, Marinduque

1886-1992

Date of Birth : June 1, 1979

Place of Birth : Sta. Cruz, Marinduque

Weight : 53 kgs.

Height : 5’5”

Status : Single

Citizenship : Filipino

Religion : Roman Catholic

Sex : Male

With good practice of 5’s.

Electrical wiring installation and design.

Can read and interpret electrical schematic diagrams.

Knowledge in using tools like Dial Gauge, Pin Gauge, Vernier Caliper (Digital and Manual), Micrometer Caliper, Ring Gauge, and Filler Gauge.

Computer Literate (Microsoft Word, Microsoft Power Point, and Microsoft Excel).

With Drivers License.

Available Upon Request:

Contact this candidate