Electrical Driver

KEVIN M. MOYE

**** *********** ******, *.*., #***, Washington, DC 20020

**************@*****.*** 202-***-****

Summary of Qualifications

** ***** ** *********** ********** in all phases of the commercial and residential areas.

Skills & Abilities

Review prints and schematics for both residential and commercial sites and follow lays-outs.

Successfully service box out, lay out new housing projects, pull wire and make the correct splicing and connection to all devices.

Wiring on all devices inside homes from an outlet to an electric range; all switches from a single pole to four ways.

Trouble-shoot all aspects of electrical problems. Install electrical devices for electrical components to determine the problem(s) and execute required repairs. Utilize the required tools to conduct troubleshooting such as, Amp probe, volt com, and continuity tester to determine whether the line side of the cable has been broken, wasn’t properly hooked up, a short in the line or whether the device it is hooked up to may be defaulted.

Operate all types of power tools to test equipment such as, Sawzall, Hammer Drill, Band Saw, Electric Drill, etc. Operate all hand tools for instance, Screw Driver, Hammer, Torpedo Lever, Pliers, Nut Driver, and Tape Measure, etc. Examine and comprehend the prints and schematics.

Read and understand the code by the N.E.C. or state and county.

Run pipe, ridge, PVC or EMT. Ability to bend pipe – off sets 90 degrees saddles. Run circuits and proper voltage and wire connections for electrical systems.

Run SEC cable or Ser when required.

Wire gauge 22 ga. – 1,000 kcmil., amperes on different wire size. Familiar with the different types of wire and were it is suitable to use at and what condition it can be used – THNN, THWN, SEC, NMC, ROMEX, MI cable, ect. Wire motor controls, panels, switchgears, transformers, lights, receptacles, switches – single poles and three way, contractors, disconnectors, etc. Use meter, Amp-Probes, Volt Meter, Mega-Watts Meters, etc. Install electrical panels, switchgears, and bus ways. Calculate electrical loads. Assignments and/or projects consist of residential, industrial and commercial.

Employment History:

Wilcox Electric October 2011 to May 2016

Electrician Cheverly, MD

Temporary and/or contract assignments at new residential construction sites and services. Install panels, meters, and disconnects. Pull wire and tie into all components and/or devices such as, light switches, outlets, refrigerator, stove, dishwasher and garbage disposal, furnace, smoke detectors, ceiling fans, etc. Work with all wire size from 14/2 to 750 kcm. Troubleshoot all devices and repair all issues. Also conduct light commercial work such as, install transformers and disconnects. Run pipe work using PVC to EMT. Operate all sorts of power tools for instance, Hammer drill, Band saw, Sawzall, and Grinders. Operate all hand tools for instance, Screw Driver, Hammer, Torpedo Lever, Pliers, Nut Driver, and Tape Measure, etc.

J. H. Bradby Electric October 2008 to February 2011

Electrical Washington, DC

Assign to groundbreaking commercial and residential construction buildings. My commercial skills consist of running pipe from to 4 inches and pulling wire; Mc cable or off the spools. Install switchgear, transformers, disconnects boxes, UPS systems, generators and electrical panels. I’m familiar with the different cable, different sizes and the ampere including, there application from Mc, Thhn, Thwn, Mi cable, and So cable. Operate all sorts of power tools for instance, Hammer drill, Band saw, Sawzall, and Grinders. Operate all hand tools for instance, Screw Driver, Hammer, Torpedo Lever, Pliers, Nut Driver, and Tape Measure, etc. I’m able to wire motor controls, relays, contactors, motion detectors, etc. I practice all safety rules and regulation. Commercial construction requires me to installed electrical panels such as, high voltage and low voltage. Install switchgears which begin at 1600 amp and higher. Wired up switch gears, transformers, disconnects and bus bars. Bend and run pipe. Install appliances and devices such as, light fixtures, outlets, smoke detectors, chillers, and furnaces, etc. Troubleshoot and resolved all kind of devices for instance, switch gears to outlets. Work on fire alarm systems. Perform residential assignments of all phases at new construction sites to service calls, which required

trouble shooting and installation. Handle forms of 120 to 480 volts and direct current volts (circuitry devices).

Wilcox Electric January 2004 to July 2008

Electrician Cheverly, MD

Assign to new residential construction and service. Install panels, meters, and disconnects. Pull wire and tie into all components and/or devices such as, light switches, outlets, refrigerator, stove, dishwasher and garbage disposal, furnace, smoke detectors, ceiling fans, etc. Work with all wire size from 14/2 to 750 kcm. Troubleshoot all devices and repair all issues. Also conduct light commercial work such as, install transformers and disconnects. Run pipe work using PVC to EMT. Operate all sorts of power tools for instance, Hammer drill, Band saw, Sawzall, and Grinders. Operate all hand tools for instance, Screw Driver, Hammer, Torpedo Lever, Pliers, Nut Driver, and Tape Measure, etc.

Other Experience:

Electrician Kolb Electric 2002-2004 Rockville, MD

Advance Helper Becker Electric 2001-2002 Alexandria, VA

Electrician Helper EMF Electric 1999-2001 Chantilly, VA

Education:

Dunbar Senior High School

Diploma received: 1983

General Studies

ABC Incorporation

Chantilly, VA

Contact this candidate