Maintenance Electrical
Resume:
Carl V. Covington
Hope Mills, NC 28348
*******@*****.***
Eagle Point Apts. (09/2013 – Present) Maintenance Tech
Fayetteville, NC fulltime 40 hrs.
Serviced, repaired and troubleshoot Goodman, Carrier, Rudd and Bryrant HVAC systems. Troubleshoot and repaired electrical systems and components on HVAC systems. Replaced hot surface igniters, inducer fan motors, and flame sensors. Pressurized hvac systems with nitrogen to check for leak in systems. Vacuumed down and charged system with refrigerant. Replaced run capacitors, condenser fan motors, compressors, thermostats and contactors. Replaced gas hot water heaters, waxed ring on toilets, garbage disposals, faucets and cpcv piping. Troubleshoot and repaired electrical and gas stoves. Repaired refrigerators and dishwashers. Unclogged tubs, toilets & drains. Replaced kitchen & bathroom faucets.
BBH Consulting (07/11/2011 – 06/ 2013) – Site Supervisor/HVAC Mechanic
Fort Bragg, North Carolina United States
Fulltime 40 hrs.
Duties: Serves as the Site Supervisor for BBH Consulting Team at Tobyhanna Reset on Fort Bragg. Supervises employees and conducts interviews for potential employees. Manages time sheets and writes employee evaluations. Troubleshoot and repair commercial 5 ton/60,000 BTU and 12 ton/139,000 BTU HVAC units located on the Trailer Mounted Support System (TMSS) and 18,000 BTU split pack on Command System Tactical Military Shelters. Troubleshoot and replace defective breakers, thermostats, switches, fuses, compressors, solenoid valves, fan motors and electrical wiring using hand tools and test equipment. Vacuum down and recharge systems. Test for leaks using soap and water solution and electrical leak detector. Cut, bend and joined tubing using a torch and wrap tubing with insulation.
AECOM (12/08/2009 - 12/07/2010) - Mechanic
Kandahar, Afghanistan
Fulltime 84 hrs.
Duties: - Served as a mechanic overseas. Replaced and adjusted brakes and brake shoes on trailers.
Replace and Troubleshoot air conditioning units on MaxxPros Mine Resisted Ambush Protected Vehicle (MRAP). Replaced an engine on a M915 Line Haul Tractor. Replaced bullet proof windows on M1183. Installed fire suppressant systems and installed body armor on M1151. Troubleshoot and repaired air conditioning systems on M1151, M1183, and MaxxPros. Replaced oil pan gasket on MaxxPro. Troubleshoot and repaired start system on M915 and MaxxPro. Replaced walker beams on M1121. Troubleshoot and repaired hydraulic system on M1183 AND M1121. Performed annual service on MaxxPros, M1183, and M1121. Troubleshoot and repaired electrical systems on trailers, MaxxPros, M1121 and M1183.
ITT Industries (07/19/2004 - 12/06/2009) - Heavy Equipment Mechanic
Fort Bragg, North Carolina United States
Fulltime 40 hrs
Duties: - Served as a Heavy Equipment Mechanic on Fort Bragg. Performed preventive maintenance on HMMWV, Heavy Expanded Mobility Tactical Truck (HEMTT), Light Medium Tactical Vehicle (LMTV), Family Medium Tactical Vehicle (FMTV), Palletized Load System (PLS) and trailers. Replaced engines on HMMWV, LMTV & FMTV. Replaced upper & lower control arms and ball joints, front & rear main seals on engines, brake pads, brake rotors, propeller shafts and differentials on HMMWV. Replaced transmissions on HMMWV & HEMTT. Troubleshoot and repaired electrical, air, and fuel systems on HMMWV, LMTV, FMTV, PLS, HEMTT, & trailers. Replaced transfers, hydro-boosters, steering gear boxes & steering gear pumps on HMMWV. Troubleshoot and repaired cooling systems on HMMWV, LMTV, FMTV, HEMTT & PLS. Replaced brake shoes, propeller shafts, steering gear box & fan clutch on LMTV, FMTV, & HEMTT. Identified the problem and repaired hydraulic systems on LMTV, FMTV & HEMTT. Completed preventive maintenance, troubleshoot & repaired hydraulic cranes and winches. Performed vehicle inspection on HMMWV, LMTV, FMTV, HEMTT & trailers. Added tasks to DA Form 2404 Equipment and Maintenance Worksheet & DA Form 2407 Maintenance Request to ordered parts, scrub packet and turned in old parts.
Bass AC and Heating (09/01/2002 - 07/01/2004) - HVAC Mechanic
Fayetteville, North Carolina United States
Fulltime 40 hrs.
Duties: Created air vent holes in floor of house and air vents in the ceiling of house. Installed flexible hoses for HVAC systems and wrapped the trunk with insulation. Install thermostat wiring, thermostats, air handlers and condensing units. Installed vent hose for dryer and bathroom exhaust fans to maintain the proper ventilation for the size of the room. Calculated airflow, and the pressure-temperature characteristics for the different systems in order to locate and repair faulty equipment swiftly and to reduce inoperative time to a minimum. Check visually for leaks and audible examination of HVAC equipment components for proper operation. Troubleshoot and replaced defective switches, thermostats, electrical wiring, breakers, and fuses using hand tools and test equipment.
Lake in the Pines Apartments (08/25/2000 - 09/1/2002) - Maintenance Mechanic
Fayetteville, North Carolina United States
Fulltime 40 hrs
Replaced compressors and heating elements on HVAC systems. Test for refrigerant leaks using soap and water solution and electrical leak detector. Troubleshoot and replace thermostat, contacts, capacitors, electrical wiring, and fan motors using hand tooks and test equipment. Changed locks on apartment doors and cut keys for locks. Repaired drywall, ceilings and replaced inside doors. Replaced garbage disposals, temperature switches on hot water heaters and hot water heaters. Replaced toilets, bathtubs and repaired plumbing pipes and fixtures. Repaired electrical outlets and replaced electrical breakers. Troubleshoot and repaired stoves and refrigerators.
Wal-Mart (05/09/1997 - 08/12/2000) - Industrial Maintenance Mechanic
Hope Mills, North Carolina United States
Fulltime 40 hrs
Duties: Served as an Industrial Maintenance Mechanic for Wal-Mart Distribution Center. Repaired and performed preventive maintenance on Crown 3000 series forklifts and floor scrubbers.
Performed preventive maintenance on the conveyor system; cut and replaced conveyor belts.
Replaced the drive belt and motor on the conveyor system. Installed phones in warehouse, electrical wire conduit and wire for Pick to Light _ Put to Light System. Serviced and repaired pneumatic and hydraulic systems. Applied prescribed test procedures to explore probable reasons for equipment failure.
United States Navy (11/16/1994 - 03/08/1997) - HVAC Technician
Annapolis, Maryland United States
Fulltime 40 hrs
Duties: Served in the United States Navy as a HVAC Technician. Calibrated temperature and pressure gauges. Serviced and repaired pneumatic and hydraulic systems. Performed preventive maintenance and repaired HVAC and refrigeration systems. Troubleshoot and repair solenoid valves, electrical wiring, switches, thermostats, compressors, and fan motors. Recover refrigerant using recovery unit. Vacuum down and recharge systems.
United States Navy (08/16/1984 - 11/16/1994) - Diesel Mechanic Norfolk, Virginia United States
Fulltime 40 hrs
Duties: Served in the United States Navy as a Diesel Mechanic Rebuilt heads on Detroit Diesel Marine V12-71 engines, serviced and repaired Detroit Diesel 6-71 and 3-71 Gray Marine Boat engines. Serviced and repaired pneumatic and hydraulic systems. Overhaul valves by adjusting or replacing gaskets, springs, floats, diaphams, valve fittings, seals and couplings. Perform alignment of pumps and motors. Perform oil sampling and lubrication of various equipment. Performed preventive maintenance and repaired on firefighting equipment. Qualified damage control and fire fighting team member. Qualified on M-14, M-16, 12 gauge shotgun, and 45 pistol.
Education
High School
South View High (08/15/1981 - 06/06/1984)
Hope Mills, North Carolina
United States
Degree: High School Diploma
Description: High School
Additional Information
Training - RG-31A2 MK5E FLMNET Course (10/08/2010)
40
Field Level Maintenance New Equipment Training (FLMNET)
Training - MaxxPro Dash FLMNET Course (05/13/2010)
40
Field Level Maintenance New Equipment Training (FLMNET)
Training - Major Appliance Installation and Repair (06/14/2008)
30
Repair Major Appliances.
Training - General Manufacturing Certification/Electro-Mech (05/15/1997)
60
Continuing Education
Certification - Certificate for Processing CFC/HCFC Refrigents (11/14/1994)
40
DoD EPA Certification Program for processing chlorofluorocarbon and halon chlorofluorocarbon refrigerants. Certified as a Universal Technician.
Training - Surface Shipboard Gage Calibration Operator (03/23/1995)
32 Hours
1200 LB
(B2D, B5B, D6A and D6B)
Contact this candidate