Engineer Electrical

S.Shahabur Alam, M.ENG., P.Eng.

*** ****** ****., *********, ** S7R 0J9, Phone No: 306-***-****(h),306-***-****(c) email: ********@*****.**

PROFILE

Design protection & control scheme and physical design of 345kv/138kV/115kv/34kv/13.8kV substations, Switching Station Canada, USA

Physical design of 138kV switching stations, prepared MR, job requisitions

Installation and commissioning of substations physical system and protection scheme

Prepared transformer sizing calculation and cable loss calculation

Prepared RFP and evaluate bid for the Transformers, Breakers, Disconnect switch, Rapid ground switch, Shunt reactors also perform all calculations

Performed grounding calculation, bus bar sizing calculation, battery sizing, CT selection, Surge Arrester Selection, MV/HV switchgear selection

Designed and analyzed grounding, prepared reports

Shielding designed of a switching station

Designed load flow analyses, arc-flash hazard analyses, short circuit analysis, relay co-ordination using ETAP

Skilled in PLC, automation, SCADA, remote control system, communication protocol

Knowledgeable in electrical standard codes such as CSA, IEC 61850, IEEE, ANSI,

Skilled in ETAP, Easy power, ASPEN, Symp Ground. Elecdes, and MS-Office,2D Autocad & 3D Autocad

Skilled in design, installation, modification and maintenance of Motor, MCC, VFD for Textile mills, paper mills and west water pumping station.

Designed long route of underground high voltage cable

Designed high voltage overhead line

Review Manufacturer design and drawings

Maintain, trouble-shooting 300kv/138kV/132kv/33kv substation protection & control system, alarm system

Procurement of major electrical equipment, man-hour estimates, cost estimates, and bid proposal preparation, control house specification, equipment specifications using standard

Strong background in leading and managing projects in a changing environment

Master’s of Engineering (Electrical and Computer Engineering) Canada

Bachelor of Science in Engineering (Electrical and Electronics Engineering)

Professional Engineer (P.Eng), APEGS, SK and PEO, Ontario, Canada

EMPLOYMENT EXPERIENCE

Sr. Electrical Engineer March 2013 to March 2016

Rockwell Automation, Saskatoon, SK

Designed 138kV switching station physical system with bus profile, protection system, panel wiring, wring schedule using Elecdes software.

Conceptual design of switching station,

Prepared single line drawings of switching station

Designed grounding system, analyzed grounding with SYMP Grounding software and prepared report

Designed underground conduit system for switching stations

Sized dc Led Acid Battery system for substation.

Shielding design of switching station

Analyzed the Capacitor Bank of switching station

Designed special scheme of normal and emergency mode of operation system of a switching station

Designed and Prepared RFP and bid evaluation for breakers, Switches, Rapid ground switch, Shunt reactors, CTs

Sr. Electrical Engineer March 2012–November 2012

March Consulting Associate Inc, Saskatoon, SK, Canada

Prepared Single line deign, Short circuit analysis, Load flow analysis, Harmonic analysis, grounding analysis

using ETAP

Designed MCC, Low voltage switchgear, VFD

Pipeline grounding due to high voltage induction current, Truck grounding system design

Performed Lightning system design

Prepared 25kV cable specification and layout design, splice design

Designed 13.8 kV underground and overhead power line layout and protection system

Prepared transformer specification and designed Transformer Vault

Designed medium voltage splitter bus and connection diagram

Prepared Bid proposal, RFQ, Bid evaluation etc

Senior Protection and Control Engineer February 2011–Feb 2012

SNC Lavalin Construction, Rochester, NY, USA

Prepared conceptual design of 345 kV, 115 kV, 35 kV and 12.8 kV substation etc

Designed high voltage substation protection system

Prepared high and voltage specification of switchgear, relay, transformer, battery charger, AC/DC panel, control panel etc

Prepared BOM for high voltage substations

Designed Relay co-ordination of high voltage protection system using ASPEN

Lead Protection and Control Engineer Mar 2007–Jan 2010

Hatch Acres Corporation, Amherst, NY, USA

Responsible for protection and control design of utility transmission and distribution substations

Performed protection and control system design engineering for 345KV and 115KV substations located in the Sate of Maine, USA

Performed protection and control system design for 115KV and 34KV substations and under frequency relay replacement project for New York State Electric and Gas and Rochester Gas and Electric, USA

Was detail designer of transformer protection, transformer parallel operation, under voltage throw over using SEL relay, transmission line protection, circuit breaker operation, relay interconnecting wiring drawing, capacitor bank protection, bus bar protection, bus junction connection, bus tiebreaker operation, metering, syncro check design, annuncitor connection, ac/dc power connection

Responsible for design, modification of substation remote control systems, SCADA, Jmux, Imux, SMP-16 gateway, SMP I/O, GPS clock, touch monitor, modem, optical fiber connection

Involved in all aspects of in ground and above ground substation design

Provided relay calculations and settings, relay selection, performed CT saturation calculation, control cable voltage drop calculation, surge arrester selection

Selection of CT, PT, Fuses, circuit switcher, MV/HV Switchgear ; work flowing IEEE standard: transformer sizing, cable loss calculation, grounding calculation, switchgear specification; bus bar sizing, selection of surge arrester, battery sizing

Underground cable drop calculation and conduct sizing using AMPCALC software

Short circuit analysis and relay co-ordination using ASPEN simulation software and ETAP

Protection and Control Engineer 1999-2001

Alsthom, Kuwait

Maintenance substation Control & Protection System for high voltage substation

Carried out calculations of substation relay setting, Differential relay, Directional relay, Over Current, Earth fault relay, Solkor relay

Design and modified the substation grounding system, lightning system, fire alarm system

Design, review and modified control, relay protection and metering schemes

Prepare & review technical specification, control diagram, control cable termination diagram, switching diagram, cable route diagram, panel layout and bills of material

Prepare testing and commissioning procedures of 33/11 kV transformers, CT, PT, circuit-breakers, relay protections, metering scheme and inspected the critical events

Design and install Battery power distribution system (10000 amp A/C & DC), battery, battery charger, Rectifier, Inverter

Modify MCC(Motor control center) for a wastewater pumping station

Project Engineer 1996-1998

Monno Fabric Ltd(Process Industry) and Ananto Paper Mills Ltd, Bangladesh.

Install, maintain and modify textile machinery, Motors, MCC, VFD, control system, power system, PLC control system, computer control system, and microprocessor based machines, Cable Tray

Develop calibration and inspection procedures for monitoring instruments,

Evaluate the performance of electronic, pneumatic, hydraulic instruments and determined their servicing and replacement periods

Evaluate performance of instruments and documented their maintenance history,

Perform fault analysis of machine, identified root cause and provided technical solution

Electrical Engineer 1993-1995

Consociates International Ltd(EPCM projects), Waha Oil Company, Libya

Design and installed power system for workshop, warehouse, MCC, VFD, swimming pool and tennis court including indoor and outdoor lighting, cable tray, conduit, fire alarm system, grounding

Install electro-mechanical system: chemical injection and filtration system of a swimming pool, compressed air distribution system, serviced generator

Design underground duct bank system, main control panel, sub panel

Store Manager

Pizza 73, Saskatoon May 2010 to February 2011

Managing store and staff, Service to customer, Accounts, Cooking and prepare Pizza.

EDUCATION

Master of Engineering (Electrical and Computer Engineering) December, 2006

Concordia University, Montreal, Quebec

OTHER COURSES TAKEN

ETAP power system analysis Workshop, ETAP Canada LTD

One line diagram, Load flow analyses, Cable system, Short Circuit analyses, Motor acceleration, device co-ordination, Transformer sizing, Ground grid system design, Arc Flash analyses

QEW (Qualified electrical worker) training April, 2011

Construction Safety Training System(CSTA) from SCSA, Saskatchewan May, 2011

Auto CAD

Concordia University Continue Education

PUBLICATION

“3-Phase Fault Current Limiter For Distribution Systems,” IEEE International Conference on Power Electronics, Drives and Energy Systems for Industrial Growth-2006 (PEDES-2006)

Contact this candidate