Quality Assurance Technician

Emelito V. Baysa

*** ********* **

San Jose,Ca **127

HOME 408-***-****

CELL 408-***-****

Email# ********@*****.***

OBJECTVE:

To obtain a position that would utilize my experience and knowledge with Manufacturing Technician.

SUMMARY OF QUALIFICATIONS:

Strong working background and capacities in Equipment Maintenance/ FacilityMaintenance skills experienced with Electrical, Mechanical,

Pneumatic and Hydraulic, Motor Electrical controls. Knowledgeable with variety of Equipment Photo, Test, Packaging, Vacuum, Automated Conveyor

system, Plumbing, Drywall, Painting, Welding, Brazing.

Training and experience CRHVAC/Refrigeration, Multi-task skilled, ability

to learn quickly. Efficiently and possess good judgment.

WORKED EXPERIENCED:

MAY 08, 2013-September 19, 2013

WESTERN DIGITAL/KELLY SERVICES

4100 OSGOOD ROAD FREMONT.

DEVICE MANUFACTURING TECHNICIAN.

Process Wafer production, Running Sukodo Coater Machined, load and unload wafer parts, checked the lot, checked wafer ID, check the program number or the spin number before you load the machined, checked the thick Resist, checked the designated port to be loaded. Run the Daily and Weekly monitor. Monitors Wafers must be Coated,Baked and Measured with in !st four hours of each Shift and DATA entered into SPC Chart with in six hours of the beginning of each shift.

JUNE 19, 2010- MAY 08, 2013. Specialized in Bathroom Renovation, Room extension, Flooring, HardWood, Pergo,Tiles, CounterTops, Wall Cabinet, Base Cabinet, Plumbing, Crown Molding, Painting,Texture, Roofing, Install and replace new water heater HomeAppliance: TroubleShoot, Washing Machine, Dryer, Refrigeration, recover and charged of refrigerant, Replaced Board Control, changed water Pump, Belt, Replaced Motor and Replaced Compressor

LASER CARD

1870 N Shoreline blvd, Mountain View, CA 94043

July 16, 2008- June 18, 2010

Manufacturing Technician:

Process production work including hot lamination, die cutting edge sealing,

Bar coding, chin up and optical serialization.

Documentation of products Results.

Implementing Engineering experiment and document result.

Cross train on other card manufacturing.

Perform quality involving visual inspection and use of variety of measurement

Tools such as micrometer.

Perform reasonably related duties as assigned by immediate supervisor or other

As required.

Check pressure reading on temperature controller is at 70psi

Visually check that adhesive needles are properly aligned with the cards while in process.

Checking the width and height measurement of the cards by using micrometer.

Check for correct parameters heater temperature air pressure, glue color, and needle alignment. Perform preventive maintenance, repaired mechanical and electrical problem on PLC motor ALLEN BRADLEY. Check program temp both on heating and cooling station, check the cassette orientation and the RFID quality Assurance Control.

MMC TECHNOLOGY A MAXTOR COMPANY 09-20-2000-05-04-2006

2001 Fortune Drive San Jose CA. 95131

Equipment/ Facility Maintenance Technician. To troubleshoot and repaired

Mechanical, Electrical, Pneumatic problems on all the equipment used to

Manufacturing thin film media vacuum photo lithography equipment and

Assemble/Disassemble Target, change target, installed and set up new

Equipment on production line successfully-perform multiple types of skills

on all equipment and perform preventive maintenance on all equipment.

Helium and Leaked check detector experienced.

KOMAG INCORPORATION 04/15/1999-09/15/1999

Autumnvale San Jose CA. 95131

Equipment Maintenance. to troubleshoot automated robotic texture machine

(EDC) IBM laser and Texture, Robotic Hardware operation machine,

Oliver wash, disk cleaners, dry and wet conveyor system, performed weekly, Monthly,

Quarterly and semi annual preventive maintenance.

WESTERN DIGITAL 08/20/1995-04/16/1999

Tasman Drive, Santa Clara CA.

Lead Final Test Production.

Certify in robotic Glide, Certify and Unified. Machine in Lube Process, Baked and SPC Chart, Inspected all visual defect on the Disk surface under the microscope in regular Ultra bright inspection light, Data Entry, Secured Pass down, Interacted with the process Engineers to certify the Disk, systematically sampled disk from numerous machine for qualify and reliable of product entered. Able to adapt frequent changes, Approachable and positive Role model, Supportive and always willing to be involved.

TRAINING:

Emergency Response Team Training, Chemical Handling

Training, Disk Substance storage, Safety Training in Environmental

Orientation, Forklift Training, Basic Electrical Safety Training, Basic Lock Out/

Tag out Training. Basic Laser Safety Awareness Training.

EDUCATION:

02/26/07- 03/31/08

Institute for Business and Technology

CRHVAC/Refrigeration Diploma

EPA Universal Certified Technician[

Contact this candidate