Resume

Sign in

Sr test tech

Location:
Oakland, California, United States
Posted:
June 10, 2019

Contact this candidate

Resume:

Kim Hayes

Engineering Tech - Zoox Inc

Sunnyvale, CA

302-***-****

Utilize

Willing to relocate: Anywhere

Authorized to work in the US for any employer

Work Experience

Sr Engineering Tech

Zoox Inc - San Carlos, CA

September 2018 to Present

Test measurement equipment, Summarize data test procedures & documenting test results ● Prototype assembly, Test implementation on devices, ● Assembled test fixtures and setups to facilitate product testing, Intrinsic test

● Troubleshot test equipment ● De bugg and download software as well as troubleshoot errors

● Interpreted drawings, performed modifications and accomplished rework to new and used subassemblies ● Execute test cases in house and interpret and report testing results, ● Test reports ● Intrinsics and Calibration measurements and documentation ● Supported Engineering team support,

● Troubleshot test script (Python, Jpeg)Debug boards Google Docs, ● quality assurance practices to ensure that connected devices meet all target requirements, Environmental Test, QC /Battery Test Technician

Verlyn Inc - San Francisco, CA

November 2017 to September 2018

Mechanical assembly, Medical Device assembly ● test measurement equipment, Summarize data test procedures & documenting test results ● Handle Battery samples after assembly, Run test,JIRA,Slack

set up, Battery Life Cycle Test and data ● Environmental and mechanical reliability testing, for documentation, report generation Record, analyze, and report test results using spreadsheets, Research and development SOP's ● Lithium ion Battery test, Warm machines for verification test ● Clean room Prof Medical device assembly, Adhesives glues during assembly ● Workmanship, safety and productivity ● Incoming and outgoing QC inspection Performed optical cavity assembly on sensors

● Assembled test fixtures and setups to facilitate product testing. Device Calibration, basic mechanical and electronic troubleshooting Document and report on issues found during testing ● Prototype assembly, Test implementation on devices, ● Troubleshot test script (Python, Jpeg)Debug boards Google Docs, ● Interpreted drawings, performed modifications and accomplished rework to new and used subassemblies

ac9krf@r.postjobfree.com

QA Technician

Infineon Technologies Inc - San Jose, CA

November 2016 to September 2017

QC & QA Tech ● Inspect Sub-assemblies Clean room knowledge ● Perform; assemble optical, mechanical, electronic components and assemblies QA QC Documentation compliance with customer standards and mil spec ● Document and report on issues found during testing Prototype assembly ● Troubleshoot Element Evaluation test Mechanical assembly ● Inspected parts for calibration principles Jig fixture assembly ● Verified Mil Spec standards were in compliance w customer ● Built and assisted engineers with construction of electro-mechanical test fixtures Built from drawing vision related components and equipment ● QC customer samples ● Quality assurance practices to ensure that connected devices meet all target requirements

Sr. Test Technician

Google Inc - Mountain View, CA

August 2015 to August 2016

Conducted inventory count once week Tested battery adapters ● Prototype Assemble, Install, repair, and test and trouble shoot MOBO's and assemble sensors, modules, ● Hand Torqueing, Hand tools ● Google Docs, Electrical & electronics testing on circuits Install, repair, and troubleshoot Self-driving System components, including sensors, modules, and integrated sensor stacks ● Device Calibration, basic mechanical and electronic troubleshooting Mechanical assembly ● Debugged boards on sensors, Chamber and environmental test, Mechanical assembly ● Incoming and outgoing QC inspection Performed optical cavity and mirror assembly on sensors ● Assembled test fixtures and setups to facilitate product testing. Troubleshot test equipment ● Interpreted drawings, performed modifications and accomplished rework to new and used subassemblies ● Supported Engineering team support, ● Destructive testing and gather data from a variety of proximity sensors Collected and troubleshot large amounts of data on test Burn in, life test, current readings. Sr. Test Technician

Arista Networks Inc - Santa Clara, CA

December 2013 to May 2015

Trained interns on mechanical assembly BOM & software programming Managed and drove test yield improvements ● Assemble cable harnesses Electrical Assembly Mechanical ● Programming Proximity sensors Electrical mechanical subsystems Program CPLD"s ● Implemented test scripts using scripting language, Python etc., debugging and root cause analysis ● Evaluated technical readiness prior to release ● Establish network card configurations ● Troubleshoot and repair computer network- based equipment to the lowest replaceable unit ● Performed Diagnostic- testing, ● Troubleshot, Environmental Chamber Testing, FVT-C, FVT, FVT I, FST, EDVT ● Prepared batteries for testing, ● Collected and analyzed large amounts of data. Managed test processes and procedures ● Setup and analyzed temperature controlled tests ● Supported HW lab, general troubleshoots operations test processes and actively enhance efficiency, ● Tested batteries & Cell qualification DC Power supplies repair ● Load an assemble fixtures in test stations ● Set up of tests for engineers and executing test checklists, Loaded and unloaded environmental thermal chambers Sr. Materials Handler

TTI Staffing Agency - San Jose, CA

September 2012 to November 2013

Stored, counted and distributed materials, parts, equipment and supplies Pulled materials per requisition and order ● Performed inventory of raw materials and finished goods ● Administrative duties included: 10key, Phones Data Entry, and Inventory Made appropriate SAP transactions according to Company guidelines ● Maintained the records of different equipment and tools. Kept list of defective and expired materials.

● Recorded, delivered, and replenished related supplies in a variety of warehouse areas Loaded and unloaded materials from inbound and outbound shipping areas Sr. Assembler Tech/QC Inspector/Department Lead

Cast New Holland - New Holland, PA

August 2009 to November 2012

Rebuilt parts and tools for maintenance repairs Assembly Line ● Modification repair on subassemblies. Responsible for shipping and receiving of orders Planning and co-coordinating walk-in drives and scheduled drives at engineers & client place Assembly prototypes, deburring and composite fabrications ● Cable harness re-work wet solder, composite molds, and jig fixtures repair Performed inspection of own and other's work for failure analyst Warehouse inventory SAP and data entry ● Performed assembly line inspection and assembly modules Manufacturing maintenance of tool modifications ● Final packaging ● Improved manufacturing operations test processes and actively enhanced efficiency, consistency, cost avoidance, and customer satisfaction ● Evaluated technical readiness prior to release

Sr. TestTechnician/Composite Fabricator

Boeing Helicopter

March 1996 to September 2008

V 22 Osprey Appache) ● Assembled, installed and inspected aircraft components according to blue prints and assembly drawings and company standards, Assemble and Install wire and cable harnesses

● Mil Spec, Electrical and mechanical preparations ● Environmental Systems, Thermal Vacuum test, Acoustic Test ● Operated hand and power tools including but not limited to drill press, grinders, scales, shears, air guns and gauges ● Fabricate modify and install wire harnesses assembly ● Acoustic Test, Thermal /Vacuum ● Electrical safety checks, and test equipment calibration ● Hand Tools, Grinders, Drill press ● Mechanical assembly, Verification of flight software, manual test ● Assembly Line and jig fixture assembly Evaluated technical readiness prior to release ● Performed wire soldering, wire harness, testing and modification of wire bundles Performed data entry to appropriately track and document materials information Composite fabrication, fixture assembly and CMM. Investigate products and assessments Worked in clean room environment ● Worked in conformance with established manufacturing test processes and procedures Developed test process ● Configured Cable Harnesses, Composite repair, bonding composite molding, sealer Load an assemble fixtures in test stations

Education

Bachelor's

Skills

Hand Tools, Networking, Word, Microsoft Excel

Additional Information

Skills

Low Voltage



Contact this candidate