Electrical Engineer

Redner Sanchez Africa

Kayumanggi Lipa City Batangas, Philippines

Mobile No. : +639*********

Email : ******.******@*****.***

ELECTRICAL ENGINEER

Registered Electrical Engineer of the Philippines, REE License No. 34965 (issued Oct. 28, 2004)

Electrical Engineering Professional with experience in Engineering, Construction, Testing, Inspection, Commissioning, Calculations, Design, Drafting, Review and Checking of Electrical Drawings for Power, Lighting, Grounding, Area Classifications, Electrical Cable Tray, Single Line Diagrams, Connection Diagrams, Block Diagrams, General Arrangements, Layouts, Control Schematics, Cable Schedule and Material Take-off (MTO), ensuring clarity, completeness and minimal errors in design output and compliance to project specifications, manhour budget and schedule.

Familiar with the different international standards such as NEC, IEC, BS, ABS, DNV, SOLAS, IEEE and others.

PROFESSIONAL EXPERIENCE

(13 years : On-shore and Off-shore OIL and GAS Projects)

Electrical Engineer Aug 2018 – present

Ambitech Asia Inc.

West 1903B Philippine Stock Exchange Center, Pasig City, Metro Manila 1605

Project : UOP LLC (Engineering Project)

Prepare, check and review design deliverables such as: Single Line Diagrams, Loadlist, Cable Schedules, Panel Schedules, Bill of Materials, Hazardous Area Classification layout, Substation layout, Distribution Plans, Power & Control Layout, Lighting Layout, Grounding Layouts, Motor Schematic Diagrams, Interconnection Diagrams, Riser Diagrams, Installation Details, Cable Tray / Conduit Routing Layout, and other design deliverables.

Perform calculations, sizing, specifications and other tasks such as Cable Sizing, Electrical Equipment Datasheets and Sizing, Design Basis, FEED studies, Construction Bid packages, Cost Estimates and Vendor/Contractor Document Reviews.

Incorporation to design the local and international standards such as Philippine Electrical Code, NEC, NFPA, IEEE, IEC and other industry and client-specific codes and standards.

Coordination, attend to meetings with other project leads, client, vendor and contractors. Monitor, control and plan assigned project resources such as man-hour, schedule, references and deliverables.

Ensure company’s Quality Management System and related engineering and documentation procedures are implemented in all phases of project execution.

Supervise, mentor, provide technical direction to less experienced engineers and designers.

Electrical Engineer (Site) Dec 2015 – July 2017

TEEKAY NAVION OFFSHORE LOADING PTE. LTD.

Sembawang Shipyard, Admiralty Road West Singapore 759956

Project : GINA KROG FSO

Representing the Owner as Electrical Engineer, my main responsibility is to check the electrical engineering deliverables of the Main Contractor / Shipyard (SEMBAWANG) and Package/Equipment Vendors according to IEC, DNV and TEEKAY standards. Specifically :

Prepare Voltage Drop Calculation, Cable Sizing Calculation, Breaker/Fuse Sizing Calculation of the MV (11kV) and LV (690V, 400V and 230V) System

Review and Checking of the Single Line Diagrams, Interconnection Diagrams, Control Schematics, Cable Block Diagrams, Wiring Diagrams, Loop Diagrams, Interface Diagrams, Cable Schedule, Overall Earthing Diagram

Preparation of Cable Ladder Layout

Site Inspection, Site Coordination, Construction Progress Monitoring

Review Instrument Documentations for proper Electrical Interface with regards to PSD, ESD, PCS, Fire & Gas etc

Coordination with Main Contractor / Shipyard, Construction Department, Commissioning Department etc with regards to Electrical Engineering issues

Site Support/Supervision with regards to Construction of Electrical Equipment according to approve drawings and standards

Electrical Engineer (Site) April 2015 – Sep 2015

DANA PETROLEUM

COSCO Shipyard, Qidong, Jiangsu 226200, China

Project : Western Isles Development Project (WIDP) FPSO

Representing the Owner as Electrical Engineer, my main responsibility is to check the electrical engineering deliverables of the Main Contractor / Shipyard (COSCO) and Package/Equipment Vendors according to BS, IEC, DNV and DANA standards. Specifically :

Prepare Voltage Drop Calculation, Cable Sizing Calculation, Breaker/Fuse Sizing Calculation of the MV (11kV) and LV (690V, 400V and 230V) System

Review and Checking of the Single Line Diagrams, Interconnection Diagrams, Control Schematics, Cable Block Diagrams, Wiring Diagrams, Loop Diagrams, Interface Diagrams, Cable Schedule, Overall Earthing Diagram

Review and Checking of Lighting and Small Power

-Cable Schedule, Layout, and Single Line Diagram Discrepancies

-Circuit impedance verification and Short Circuit Calculation

Review and Checking of Vendor Packages

-Electrical Power Package (MV/LV Switchboards, Lighting and Small Power System, MV / LV Transformers, MV / LV Motors)

-Mechanical Packages (Electrical Content and Interface)

Review of Design Philosophy :

-Cable Selection Philosophy, Cable Gland Management Procedure, Electrical System Description, General Technical Specification for Equipment

Review of Safety Automation System (SAS)

-Discrepancies between Power Distribution and Control System (PDCS) Wiring Diagrams and Cabinet GA / Layout, I/O List, SAS Topology

-Electrical Control Typicals for SAS

Site Inspection, Progress Monitoring, Red Line Mark Ups for As Built Purposes

Review Instrument Documentations for proper Electrical Interface with regards to PSD, ESD, PCS, Fire & Gas etc

Coordination with Main Contractor / Shipyard, Construction Department, Commissioning Department etc with regards to Electrical Engineering issues

Sr. Electrical Project Engineer May 2012 – October 2014

Siemens Pte. Ltd.

60 Macpherson Road, The Siemens Center, Singapore 348615

Project : ODFJELL # 3 – H3033 (DRILL SHIP – SEMI SUB)

ATWOOD # 3 – H3619 (DRILL SHIP) / ATWOOD # 4 – H3622 (DRILL SHIP)

Manage all aspects of Electrical Engineering in the design of (1) Low Voltage (690V, 440V and 230V ) Electrical Power Distribution System, Switchboard, and Intelligent MCC, (2) MV Dry Type Transformer

Supervise contractor’s/vendor’s execution of engineering design, equipment fabrication and testing

Coordinate with customers, suppliers/vendors, principals, surveyors and 3rd party inspectors on project requirement

Organise production documents packages for internal use and customers

Assist factory/vendors during engineering, production, internal testing of equipment, Factory Acceptance Test (FAT), and Site Acceptance Test (SAT)

Monitor and expedite module fabrication, inspection, supply and delivery to the Construction Site, ensuring technical, quality, cost and schedule issues are properly resolved

Plan and control project schedule and costing as per contractual delivery time and cost budget established for the projects

Raise project variation to customer and negotiate change orders

Act as a single contact with customer and vendors during project execution and consolidate technical and commercial issues for coordination

Support the Client Completions Team ensuring punch listing and pre-commissioning and commissioning activities are carried out effectively and Handover documentation delivered as needed

Electrical Engineer Sep 2010 – May 2012

Kongsberg Maritime Engineering

81 Toh Guan Road East #04-01, Secom Center Singapore 608606

Project : BW JOKO TOLE (FPU)

Prepare Voltage Drop Calculation, Cable Sizing Calculation, Breaker/Fuse Sizing Calculation, (MARINE SIDE)

oMV (6.6kV) and LV (440V and 220V) System

Prepare Single Line Diagrams, Interconnection Diagrams, Control Schematics, Cable Block Diagrams, Wiring Diagrams, Loop Diagrams, Interface Diagrams, using AutoCAD LT 2011 for the following Electrical Items:

o6.6kV MV Switchgear

o440V Normal LV Switchgear / 440V Emergency Switchboard / 440V Essential LV Switchgear

oUPS System

o440V Laundry Distribution Board / 440V Workshop Distribution Board / 440V Galley Distribution Board

o220V Lighting and Small Power Distribution Boards

oHP Compressor / LP Compressor (by SOLAR)

oSUBSEA System

oLIFEBOAT and FRC System

oHelicopter Re-Fuelling / De-Fuelling System

oNavigational Aids System

oLighting and Small Power

Prepare General Arrangement Drawing and/or Layout Drawing, specifically for:

oMV (6.6kV) and LV (440V and 220V) Switchboards

oLighting and Small Power Distribution Boards

oHazardous Area

oEngine Room Cable Ladder

oMulti Cable Transit

oElectrical Equipment for Switchgear Room, Engine Control Room

oEarthing System

Prepare Typical Installation Details, specifically for:

oEarthing System

oMotor Local Control Station

Prepare Lighting MTO, Lighting and Small Power Load Balancing

Review / Check Instrument Department’s Termination / Block Diagram for the proper Electrical Interface with regards to ICSS (PSD, ESD, PCS, Fire and Gas, etc)

Assist in the preparation of Electrical Cable Schedule, Protection Devices Setting Table

Review Vendor Documents and incorporate all the necessary information to the Company’s Electrical Deliverables

Perform progress reporting on design and drafting activities

Ensure consistency and integrity of electrical design throughout the project and reviewing design for logic, functionality and completeness

Electrical Engineer II Aug 2008 ~ Sep 2010

CB&I LUMMUS PTE LTD

3A International Business Park, ICOn @ IBP Singapore 609935

Project : TUPI (FPSO)

Review Vendor Documents and incorporate all the necessary information to the Company’s Electrical Deliverables

Prepare Voltage Drop Calculation, Cable Sizing, Cable Schedule for the different Modules of the FPSO Vessel

Prepare Single Line Diagrams, Interconnection Diagrams, Control Schematics, Cable Block Diagrams, Wiring Diagrams, Interface Diagrams of MV/LV Switchboards, Distribution Boards, Electrical Panels etc, using the latest version of AUTO CAD

Coordinate with other disciplines, vendors, clients with regards to Electrical Concerns of the Project

Electrical Engineer I June 2005 ~ Aug 2008

JGC Philippines Inc.

Ayala Alabang, Muntinlupa City, Philippines

Project : Various on-shore Oil and Gas / Petrochemical / Nickel Mining Projects (EPC)

Project Project Location Assignment Location

Dolphin Project Ras Laffan, Qatar Manila Philippines

Stephan Project Batangas, Philippines Manila, Philippines

Hawiyah Project Saudi Arabia Manila, Philippines

Dolphin Project Ras Laffan, Qatar Ras Laffan Qatar

Kimberly Project Australia JGC Yokohama

CBNH2 Project Rio Tuba, Palawan Rio Tuba Palawan

RPLC Project Venezuela Manila, Philippines

Specifics:

Manila and Yokohama Office

Equipment Modeling of the Lighting System of the Project (Kimberly), using PDMS (AVEVA) software

Design of Electrical Drawing specifically:

oLighting, Power, Grounding (DOLPHIN, HAWIYAH)

oArea Classification (RPLC)

oConnection Diagram, Single Line Diagram (STEPHAN)

oElectrical Cable Tray (HAWIYAH)

oMaterial Take-off (HAWIYAH)

oPreparation of Drafting works related to P&ID Diagram, Graphics Diagram (HAWIYAH)

oPreparation of Multi Cable Transit Arrangement. (HAWIYAH)

oPreparation of MTO for Electrical Cables. (HAWIYAH)

oDrafting of Electrical Cable Tray (DOLPHIN,HAWIYAH)

Site Assignment

Ras Laffan Qatar (DOLPHIN PROJECT)

oChecking of actual site condition to determine the discrepancies between Cable Schedule, Block Diagram, Wiring Diagram, and Layout of Telecommunication Drawings (CCTV System, Marine System, Meteorological System, OTN System, PABX System, PAGA System, Security Access And Control System, and Structured Cabling System) and revising them accordingly for “as-built” purposes.

oChecking of CCTV System, PAGA System and Security Access System before commissioning, with the supervision of more experienced Telecom Engineers. This includes loop checking and Impedance checking of PAGA Cables, and Loop checking of Security Access System wiring, inspection of camera functions for CCTV etc etc.

oPreparing and checking of Ready for Commissioning (RFC) and Ready for Start-up (RFSU) Dossiers before issuance to client

oCoordination with other Sections (Building Section, Instrument Section, Vendors, Subcontractors) regarding Documents, Drawings, Files, and Actual Plant Condition concerning Telecommunication System

oAssists in the Commissioning of Telecommunication System

oAssists in “punch killing” of Telecommunication System

Rio Tuba Palawan (CBNH2 Project)

oAttend to the activity of Subcontractor with regards to Electrical System Construction, Pre-Commissioning and Commissioning specifically on the field of Grounding, Lighting, Power, and Substation

oWitness Electrical Test Inspection as per Client Specification and Standards specifically; (1)Insulation Resistance Test for motors, generators, and LV/MV cables, (2) Winding Resistance Test, (3) Phase Rotation Check etc etc

oPrepare Cable Pulling Schedule of Electrical System

oCoordination with Client, Subcontractors, Vendors and other Disciplines with regards to the Electrical System of the Plant

oResponsible for electrical construction’s progress monitoring

Staff Electrical Engineer Aug.2004 ~ June 2005

IQA Section, Parts Engineering Department

EPSON PRECISION PHILIPPINES INC.

Lima Technology Center, Lipa City Batangas

Responsible for the Quality Assurance of the “Incoming System” of the Company

Assist the supervisor/Assistant Supervisor on the control, evaluation, and inspection of parts and evaluation sample for approval

TECHNICAL SKILLS:

Has proficient knowledge on the following software skills:

E3D (Everything 3D)

Microsoft Office Application

ETAP / SKM (basic Knowledge)

PDMS

AutoCAD

Microstation

Luxicon (for Lighting System Calculation)

SEMINARS / TRAININGS ATTENDED:

Short Circuit Calculation and Analysis IIEE Philippines 06~07June 2008

SKM Power Tools for Windows Siemens Pte. Ltd.

Electrical Transient Analyzer Program(ETAP) Siemens Pte. Ltd.

High and Low Voltage

Switchgear Operations Course ATTS Pte. Ltd. 26~29 Aug 2013

EDUCATION

BATANGAS STATE UNIVERSITY, Batangas Philippines

Bachelor of Science in ELECTRICAL ENGINEERING, 2004

LIPA CITY SCIENCE HIGH SCHOOL, Batangas Philippines

High School Diploma, 1999

TANGWAY ELEMENTARY SCHOOL, Batangas Philippines

Class Valedictorian, 1995

PERSONAL INFORMATION:

Date of Birth : September 5, 1982

Status : Married

Nationality : Filipino

Religion : Roman Catholic

Spoken Language : Filipino / English

Height : 5'5"

Weight : 130 lbs

CHARACTER REFERENCE:

Name: Ernie Luzano

Contact Number: Mobile # +659*******

Email: *****.******@******.***, *************@*****.***

Position: EIT Interface Engineer

Company: Teekay Navion Offshore Loading (Singapore)

Name: Ruel Magracia

Contact Number: Mobile # +659*******

Email: ************@*****.***

Position: Lead Engineer

Company: Kongsberg Maritime Engineering (Singapore)

I hereby acknowledge that all of the above information are valid and correct.

Redner S. Africa

Contact this candidate