Curriculum Vitae
Babar Nisar S/o
Abdul Nisar
Contact No.: +92-300-*******,+92-312-*******
E-mail: ac7ff4@r.postjobfree.com
Date of Birth: 23/10/1993
CNIC No.: 34602-9077353-5
Passport NO.: JC9823531
Temporary Address: 2nd Floor, House # 10,
Bismillah Block III, BOR Society, Johar Town Lahore Permanent Address: Gali Darziyan Mohallah Machi
Wara Chawinda, Tehsil Pasrur, District Sialkot
Objective
To be a part of the challenging team as a professional Engineer, which strives for the better growth of the organization and which explores my potential and provides me with the opportunity to enhance my talent with an intention to be an asset to the company. Education
2012-2016 B.Sc. Electrical Engineering (Electronics) PEC Number: ELECT/58925 CGPA: 3.00/4 70.6%
Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan
(HEC & PEC Recognized)
2009-2012 Higher Secondary School Certificate (HSSC) FS.c(Pre-Engineering) Marks: 868/1100 78.90%
Board of Intermediate & Secondary Education (BISE) Gujranwala – Pakistan
2007-2009 Secondary School Certificate (SSC)
Matric(Science) Marks: 853/1050 81.23%
Board of Intermediate & Secondary Education (BISE) Gujranwala – Pakistan
Professional Experiences
Service Engineer At Al Fouz Technologies Lahore 2017-Present
Installation, Testing & Commissioning of Flow Transmitter
Installation, Testing & Commissioning of Level Transmitter
Installation, Testing Of VFD Panel at Pakistan OilFields Limited
Installation, Testing & Commissioning Of Power House LT Panels at Pakistan OilFields Limited
Installation, Testing Of ATS Panel at Total Parco
Installation & Testing of Current Transformer 5000/5A at Nestle
Inspection & Installation of Bus Coupler at Sarhad Textile
Designing, Installation & Testing of DOL Starter
Designing, Installation & Testing of Star Delta Starter
Designing, Installation and Testing of Distribution Box
Design, Installation & Testing of ATS Panel For Phase Failure
Design, Installation & Testing of PFI Panels
Cable Termination
Configuring of Synchronization panel with GU 660A Module
Installation & Maintenance of Air Circuit Breaker
Inspection & Testing of Circuit Breaker up to 1000A
Designing & Installation of 3 phase Mains & Generator through ACCL
Evaluation of Total Bill Of Quantity(BOQ)
Trainee Engineer At Chishtia Sugar Mill Nov. 2016- July 2017 As Trainee Electrical Engineer in Chishtia sugar mill, I worked in electrical department on switchgear and motor control center. Switch Gear is combination of disconnect switches, fuses and circuit breaker to control, protect and isolate the electrical equipment. Switchgear is basically used to de-energies the equipment. Switchgear may be used for high voltage and low voltage.LV switchgear may be within a building up to medium voltage or protection and control. This is the general description about switchgear. Inside Motor control center different types of motor starters are used which are star delta starter, DOL starter. how to use these starters are depend on motor ratings. If motor KiloWatt power is 7.5 or less than 7.5 then DOL starter is used and above 7.5 KW then star delta starter is used. Final Year Project
Head Gesture Controlled Smart Wheel Chair
The components used in this project are MPU6050 motion sensor, Arduino Uno microcontroller and H- Bridge using MOSFETS for controlling of DC Motors. Besides these Relays, Opto couplers and Transistors are also used for switching purpose.
The Wheelchair is capable of moving according to head gestures. It moves in such a way that when head is moved in forward direction the wheelchair is capable to move in forward direction & when the head is moved to opposite side of forward, wheelchair is moved in backward direction. Technical Skills
PROTEUS ARES PCB DESIGN
Microsoft Visio For Drawings
Live Wire For Circuit Designing
MS Office 2007, 2010 ( MS word, MS power point, MS excel ) Technical Report Writing
Co-Curricular Activities Awards and Honors
Event Organizer at SOCIETY OF INNOVATIVE ELECTRONICS Federal Urdu University of Arts, Science and Technology (FUUAST), Islamabad [S.I.E.F]
RUNNER UP of all Pakistan inter-university CIRCUIT DESIGNING competition in 2015 held by FUUAST university Islamabad.
Participation certificate of PLC & SCADA Workshop
Second Position in SSC School
Area of Interest:
Shut Down Projects
Automation Industry
Industry Maintenance
Power House Maintenance
Reference
References will be provided on demand