Mechanical Engineer Electrical

Eduardo Maldonado

**** ***** ****** *****, **. **922

407-***-**** (English/Spanish) ***************@*****.***, ************@***.**.***

Technical Support Engineer

Fifteen years’ experience performing engineering designs and tests with many sophisticated electronic/electrical /mechanical/optical/ computers, and documentation. For the Military, Avionics, Department of Transportation, Invensys, and C.T.D.I. Four years installing computer equipment racks in Head End (HE) computer rooms. Four years’ experience installing and repairing Military microwave assemblies at the 563rd Ordnance Company using high voltages.

Mechanical Systems

Electronics Systems

Avionics

Design Specifications

Product Performance

Calibration

Microelectronics

Rockets

Pneumatics

Fluid Systems

Optical Systems

Amplifiers and filter

Control Cabinets

Mega High/Low Voltages

Cable/Ethernet/Fiber

Computer Room

Troubleshooting Skills

Windows

HyperTerminal & Linux

MS-Office Suite

Documentation/BOM

AutoCAD 2017

Light Programming

GeNo.Inc 04/17-08-17

Jr. R&D Electrical/Mechanical Engineer

Programmed, tested, repaired, calibrated, and built prototypes, test equipment, test fixtures for a Microelectronics Nitrite Oxide (NO) delivery system for newborns. Nitrogen dioxide (NO2) is transformed into Nitrite Dioxide (NO), a lifesaving gas.

Delta Group Electronics 8/16- 4/17

Engineering Technician

Programed, tested, repaired, used porotypes, and document many microprocessors based electronic microelectronics devices, systems, and GE (RF) radios. I use all electronics mechanical test equipment to fix electronics to component level. I read schematics well and have good troubleshooting skills and interpersonal communication skills.

CTDI 11/13-9/16

Telecommunications Engineering /Mechanical Technician

I/we built an audio/visual test room; for test, repair, analyzing, and document for Cisco and Samsung (RF) cable television set top boxes. I worked on Cable Card Assemblies (CCA), HyperTerminal-(LINUX), oscilloscopes, spectrum analyzers, decibels, multimeters, schematics, (embedded RF audio-visual software), (ECN) Engineering Change Notice with automated testing.

University of Phoenix

Student-Information Technology 07/10-06/13

I attended and graduated from the University of Phoenix; I was a full-time student in (IT) Information Technology field. I learned programming, networking, and software’s for programming applications for business systems were learned.

Electronics/Mechanical Engineering Technician 02/09-02/12

Guardian Interlock Systems

I worked on (PCB’s), Printed Circuit Boards to manufacture an alcohol breathalyzer system with RS232 communication. I designed Microelectronics circuit boards, troubleshoot, calibrated, and upgraded system firmware, software. I used hand tools, oscilloscopes, power supplies, multimeters, data loggers, schematics; lock out tag out and (ESD) electrostatic discharge procedures.

Electrical/Mechanical Engineering Technician 12/05-03/08

Florida Turnpike Transportation Authority (D.O.T.)

I worked testing, repairing, and installing, electronic/electrical/mechanical instrumentation systems. I worked with the Sunpass delineator (IR) infrared systems. I installed and assembled sub-assemblies, transponder (RF) tracking systems, and (CMMS) computerized maintenance management system. I set and adjusted frequencies with a Linux (GUI) graphical user interface, and CCTV systems. Working in computer rooms networking the Florida Turnpike system.

Trolley Boats of Daytona 01/03/-12/05

Electronics/Electrical/Mechanical Engineering Technician

I installed electronic/electrical/mechanical instrumentation; pressure, temperature, (RPM) revolutions per minutes, and speed gages. I used ladder logic, electrical/mechanical schematics for an amphibious vehicle. I ran all wire harnesses and used a crimping tool for gages, radio, and motor. I used AutoCAD to redesign vehicle parts that were needed for this vehicle.

Eduardo Maldonado – ***************@*****.***, ************@***.**.*** 407.257.44 96 Page 2

Student

Valencia Community College

Electrical Engineering Technology 01/01-01/03

I was a full-time student studying all concepts of analog, digital, and (RF) Radio Frequencies electronics and technologies. I studied AutoCAD; I designed band pass filters, used oscilloscopes, hand tools, soldered, and documented all procedures.

Cape Canaveral Air Force Station

Electrical/Mechanical Engineering Technician 10/00-10/01

I installed, repaired, and replaced flow control devices at an Atlas launch facility. I used Military type block-schematics working with controlled pressurized gases instrumentation; Hydrogen, Nitrogen and Freon. I checked these system controls from a high voltage substation to a Chiller system to the low voltage PLC. I used the Heart 787 Fluke meter to test, install and calibrate these devices. I worked with a system support team to monitor devices for the Allen Bradley PLC

Dewalt - Black & Decker Company

Electrical/Mechanical Tool Bench Technician 10/96-10/97 & 12/99-10/00

I tested, repaired, and calibrated AC /DC tools, motors, appliances, lawnmowers, and pneumatic tools; foreign and domestic. I used schematics, ladder logic, pictorial breakdowns, microfiche, oscilloscopes, multimeters, soldering irons, power supplies, hand tools, cutting, sawing, and punching machinery and computers.

H.V.A.C.R. Ken & Walt’s, Crum’s Climate Control, Mr. Cool at the Oaks Apartments

Electrical/Mechanical Installation Housing Engineer 10/96-12/02

I serviced, repaired, replaced, assembled, and installed air conditioning and heating systems. I used thermocouples and sensors to correlate heat to pressure, and sized systems for placement. I have worked with chiller systems, walk in coolers, industrial, commercial, residential, and Florida water air conditioning systems. I document all procedures.

A.F.P.S. Test Laboratories

R&D Electrical/Mechanical Engineer 10/95-10/96

I worked with engineers in research and development (R & D) department testing (G.M.) General Motor automotive car air conditioning compressors, and prototyping. I used a central reclaim system, cooling chambers, heating chambers, control panels, cable harnesses, pressurized gases, vacuum pumps, multimeters, ampere probes, oscilloscopes, power supplies, and schematics.

Student

Niagara Community College

I.T. Bench Technician 12/93-12/95

Work-Study; I installed Windows Operating Systems (OS’s), I tested and repaired computers, changed out parts, hard drives, memory, motherboards, power supplies, fans, and assembled computers. I repaired electrical/electronic audio video school equipment, using meters, oscilloscopes, signal generator, power supplies, schematics, hand tools, and soldering.

Aero Instruments & Avionics Bench – FAA Facility

Electrical/Mechanical Engineering Technician 10/87-6/92

I designed, tested and manufactured (PCB’s), Printed Circuit Boards, test fixture, prototypes, for commercial aircrafts. I built, tested, repaired, wiring harnesses, cables meters, power supplies and calibrated all test equipment, and simulators per FAA specs. I used wire list, soldering iron, oscilloscopes, hand tools, schematics, drawings, (machinery)-hand-automated.

U.S. Army- Radar Repairman Disabled Veteran

Electronics Engineering Technician

I assembled, tested, repaired, calibrated, and maintained a Vulcan 27F microwave radar tracking system on a manned tank system. I tested and repaired field returned line replaceable units. I used oscilloscopes, RF meters, multimeters, signal generator, spectrum analyzer, power supplies, schematics, hand tools, a Hot Stick, and documented all work procedures

Education

B.S.I.T. The University of Phoenix in Information Technology 07/10-06/13

A.A.S. Valencia Community College Orlando FL. Electrical Engineering Technology 01/01-01/03

A.A.S. Niagara Community College Sanborn, N.Y. (H.V.A.C.R)/Mechanical Technician 01/93-01/95

Certificate

IPC610 & 620

EPA

Bucket Truck

Contact this candidate