Resume

Sign in

Mechanical Power Plant

Location:
Makati, Metro Manila, Philippines
Posted:
September 18, 2018

Contact this candidate

Resume:

JILBERT G. VILLANUEVA

#*** *** ***** ******* *******, Philippines

Tel.no#+63-919*******/+63 27944189 Email Add: ac63fo@r.postjobfree.com

Position Applied: Mechanical Technician

Career Objective: A challenging position develops through my training achievement, knowledge, education as marine engineering, experiences mechanical works gained through well-respected companies.

Summary of Qualification: Graduate of Associate Marine Engineering, presently working as a mechanical technician in FPSO offshore and also experience in oil and gas industries, power plant, oil refinery, petrochemical plant and running vessel. duties responsible for maintenance of mechanical equipment including repairs troubleshooting of defective parts, alignment fabricate of special tools and preventive maintenance and contribute to the health and safety of the working environment.

Working history

Company: BSM crew service centre

Location: Production contractor SBM-Offshore

Vessel FPSO N’goma

Blk. 15/6 Soyo, Angola

September 21, 2013, to December 22, 2016

Position: Mechanical Technician

Professional experience: Working in (FPSO)-Floating Production Storage and Offloading system, Responsible for safely performing maintenance and repair task associated with all mechanical equipment, carry out maintenance activities in accordance with company and industry standard policies procedures and repair mechanical equipment such as, Centrifugal pumps replacing the mechanical seal, bearing, left seal, wearing ring, shaft and also do the alignment. Chemical pumps replacing diaphragm, seal, charging of possession damper and lapping of suction, discharge non-return valve. Siemens Gas Turbines using on Power Gen, water Injection and Gas Compressor, maintaining and we replacing damaged parts of turbine PT, GG, gearbox, and burners, igniters, oil pumps, amot valve and clutch motor, replace filters, turbine wash and also burros coping. And Gas compressor we replacing dry gas seal checking alignment, and bolts tensioning on LP, IP, HP flange and heat exchanger replacing plate and gasket. PSV removing for calibration and reinstalled. Traveling and Pedestal Cranes Hydraulic system electric and engine driven maintained good condition replacing damaged parts changing Hydraulic pumps, oil seal, rectify leak on swivel replace hose and fittings and AMOS routine replacing Hydraulic filters and change oil on swing drive motor, greasing and checking bolts tensioning on turntable, and also rocking test. On Diesel engine replacing cylinder gasket, turbocharger and repair injection pump, starter, oil cooler, radiator and AMOS routine schedule for change oil, filters and cleaning fire arrestor. Essential and Emergency and Fire Pumps test run in auto and manual mode, checking Hydraulic system pumps hoses for seawater left pump and also servicing engine change oil and filters, valves, HVAC unit maintaining good temperature replace damaged compressor, belts on air handling unit, charging of gas and oil on to the compressor, cleaning of the condenser, filters, and dampers. Reverses Osmosis we do backwashing and chemical wash, changing membrane filters., Hydro-cyclone replacing burners and repair leak on suction pipe. Courses filter cleaning and replace damaged filters. Turret lubrication on bearing greasing on greasing point, checking of loading arm and swivel checking possession damper, oil seal Pat and reading of turret depletion. We do the job on engine room on air compressor replacing the bearing, air dryer replacing desiccant and cooling pump for STA replacing the mechanical seal and bearing and steam valves replacing packing seal, and also on steering room installed stopper on the ladder. Accommodation repair leak and door closer. AMOS routine activities monitor and inspect the equipment during running or standby operation record parameter and any abnormalities and defect on the equipment, and fabricating spare parts tools and a member of the emergency response team.

Company: BSM crew service centre

Location: Production contractor SBM-Offshore

Vessel FPSO Capixaba Offshore

Costa Do Sol, Macae (RJ) Brazil

April 27 2013 to May 21 2013

Position: Mechanical Technician

Professional experience: Working in (FPSO)-Floating Production Storage and

Offloading System, responsible for repair mechanical equipment and remove replace run spools for re-certification and change flow meter and alignment check to steam inlet flange of the steam turbine, and cleaning of strainer in the crude oil pump, inspection of the Crane Hydraulic system, and Repair valves.

Company: BSM crew service centre

Location: Production contractor SBM-Offshore

Vessel FPSO Petrobras-57

Costa Do Sol, Macae (RJ) Brazil

January 21, 2012, to March 5, 2013

Position: Mechanical Technician

Professional experience: Working in (FPSO)-Floating Production Storage and

Offloading System, responsible for the commission, start-up, and repair mechanical equipment Centrifugal Pumps replacing the mechanical seal, bearing, left seal, wearing ring, shaft and also do the alignment.and Pedestal Cranes Hydraulic system was engine driven, maintained good condition replacing damaged parts, rectify leak on Hydraulic system replace hose and fittings and AMOS routine replacing Hydraulic filters and change the oil on swing drive motor, greasing and checking bolts tensioning on the turntable, and also rocking test. On Diesel engine replacing, turbocharger and repair injection pump, starter, radiator, and also replacing wire rope. static equipment PSV removing for calibration and reinstalled use correct isolation and disconnection procedures, Hydraulic winches on the turret and offloading hose rectify leak replacing valves. Hoses and fittings. steering room installed stopper on the ladder removing oil pipe connecting and tanks. Accommodation repair leak and door closer, Monitoring the condition of equipment record what any malfunction and defects to the out work history, and fabricate piping support special tools and maintain pollution control measure materials for disposal, contribute to the health and safety.

Company: BSM crew service centre

Location: Production contractor SBM-Offshore

Vessel FPSO Frade

Rio de Janeiro Brazil

July 21, 2008, to Dec.6 2011

Position: Mechanical Technician

Professional experience: Working in (FPSO)-Floating Production Storage and Offloading System, responsible for all mechanical equipment on the top side and engine room, repair work which is carried out safely, perform in the preventive and corrective, troubleshooting of mechanical maintenance activities. Replacing defective parts of centrifugal, reciprocating, rotary pumps replacing the mechanical seal, bearing, left seal, wearing ring, shaft and also do the alignment. Chemical pumps replacing diaphragm, seal, charging of possession damper. GE Nuovo Pignone Gas Turbine using on Power Gen.replacing damage part changing of burners and igniter and Hydraulic clutch motor, Hydraulic hoses and fittings, Man Turbo Gas compressor we replacing dry gas seal checking Alignment, and bolts tensioning on LP, IP, HP Flange and heat exchanger replacing plate and gasket. PSV removing for calibration and reinstalled, Air Compressor replacing the bearing, air dryer replacing desiccant and downstream filters, RO Unit we do backwashing and chemical wash, changing membrane filters., Pedestal Cranes Hydraulic system Engine driven, maintained good condition replacing damaged parts changing Hydraulic pumps, oil seal on Hydraulic boom cylinder, rectify leak replace hose and fittings and AMOS routine replacing Hydraulic filters and change oil on swing drive motor, greasing and checking bolts tensioning on turntable, and also rocking test. On Diesel engine replacing cylinder gasket, turbocharger and repair injection pump, starter, oil cooler, radiator and AMOS routine schedule for change oil, filters and cleaning fire arrestor. H-VAC unit maintaining good temperature replace damaged compressor, Belts on air handling unit, charging of gas and oil on to the compressor, cleaning of the condenser, filters, and dampers. Inspection on Turret lubrication on bearing greasing on greasing point, checking of loading arm and Swivel checking possession damper, oil seal Pat and also Hydraulic system repair leaks changing pipe, fitting connection. Hydraulic winches on the turret rectify leak replacing valves. Hoses and fittings. Hydro-cyclone replacing burners and repair leak on suction pipe. Courses filter cleaning and replace damaged filters. Lifeboat every week have AMOS routine test run and Lowering David checking and repair Hydraulic system changing the motor. Essential and Emergency and Fire Pumps test run in auto and manual mode, replace damage parts like turbocharger, radiator, belts and checking Hydraulic system pumps hoses for seawater left pump and also servicing engine change oil and filters, valves, Accommodation repair leaks and door closer Observe operation of all equipment during to routine activities and inspection of equipment during running or standby operation record any abnormalities and defect in the equipment. Toolbox meeting to establish the scope of work activities such as safety requirement permit to work, special tools and isolate faulty component on rotating using P&ID manufacturers manual and drawing and spare part require for maintenance work, contribute to the health and safety of the working environment and safety of co-worker and member of the emergency response team.

Company: Senimdi Kurylys-Bechtel joint venture

Location: Tingizchevroil SGP, Republic of Kazakhstan

March 21, 2007, to March 18, 2008

Position: Millwright

Professional experience: Working in the construction of oil and gas plant preparation of mechanical equipment hauling of construction material and installation of mechanical such as pumps and motor, gas compressor, steam turbine gearbox, turbo expander and also vertical pump. installation of oil mess and alignment of equipment, fabricated of special tools for alignment and testing of rotary equipment final coupling alignment and flange parallelism torque up flange bolt, modification, and troubleshooting of defective parts and oil flashing of oil line installation of the filter and also the preservation of equipment and equipment and housekeeping in the area.

Company: U_Chang Plant Co.LTD

Location: 20_1yongjeondong Gu.Daejeon.South Korea

Sept. 13, 2004, to Sept. 8, 2006

Position: Millwright

Professional Experience: Samsung Project, working in hydro and steam power plant

Installation of centrifugal turbines such as stator and turbine parts

Lay-outing preparation, installation leveling, centering pre and final alignment of equipment

Installation of vessel, oil tank, and piping connection

Hydro testing and oil plashing

Working on piping, fabricating pipe shoe and support

Commissioning changing of defective parts

Start-up of rotating equipment and modification

Company: M.S. Al-Suwaidi Industrial Services Co.LTD

Location: P.O Box 991 Jubail Industrial City 31951 Kingdom of Saudi Arabia.

April 10, 2002, to April 8, 2004

Position: Millwright/Maintenance

Professional Experience : Working in oil refinery and petrochemical plant responsible for installation and maintenance of mechanical equipment full-out, disassembly,assembly and changing of defective parts, alignment adjusting of shims such as pump and motor, steam turbine, piston and impeller type of compressor gear box, pin fan cooler, valves MOV, conveyors and erection of vessel loading catalyst and chemical agent and also preservation of equipment cleaning, brushing, of metal surface applying silica gel greasing, refilling of oil lubricating checking of rotation of equipment and also responsible for actual execution of rotating equipment and preventive maintenance.

Company: Candano Shipping Lines

Location: 6th Floor Victoria Building, United Nation Avenue Ermita, Manila

July 5, 1999, to July 5, 2001

Position: Apprentice Engineer

Professional Experience : Working in cargo vessel as apprentice engineer in charge in engine department and assisting in overhauling of main engine and engine generator changing of defective parts such as piston, liner, bearing, crankshaft, cylinder head tune up and change oil of engine and also responsible for actual execution of rotating equipment such as pump and motor air compressor, oil separator, oil purifier and preservation of equipment refilling of oil, changing of filter and cleaning of fuel tank and also duty in navigation engine watch and preventive maintenance.

Communication/Interpersonal Skills:

Personal: Safety aware. Conscientious, Flexible easy learner hard worker and highly trainable and can also stand work pressure.

Leadership: Good levels of written and spoken communication, good experience of Permit to Work System.

Technical: High standard of analytical, diagnostic technical and professional knowledge on rotating equipment, pneumatic, hydraulic system, Alignment and also knowledge in Piping welding and machining.

Education background:

College: Technological Institute of the Philippines

Course/address: Marine Engineering (Quipo Manila)

Year Graduated: April 5, 1995

Secondary: Bagumbong high school

Address: Bagumbong Novaliches Caloocan City

Year Graduated: March 27, 1993

Elementary: Urduja Elementary School

Address: Urduja Village Novaliches Kalookan City

Year Graduated: April 3, 1989

Achievement/Seminars/Training Attended:

1. Basic Safety Course

2. General Tanker Familiarization

3. Shore-based Fire Fighting

4. Helicopter Underwater Escape Training

5. Proficiency in Survival Craft and Rescue Boat

6. Advanced training in firefighting

7. Confined space training- entry

8. Fundamentals of condition monitoring and vibration data

collection

Personal data:

Age: 40

Nick name: Boyet

Date of birth: July 17, 1976

Place of birth: Baliuag, Bulacan

Weight: 170 lbs.

Height: 5’7”

Religion: Roman Catholic

Civil status: Married

Wife: Benette Villanueva

Children: Julia Athena L. Villanueva / Jade Yzobelle L. Villanueva

Health: Perfect

Mother name: Mesolim G. Villanueva Decease

Father name: Jaime M. Villanueva Occupation (Farmer)

Occupation: OFW

Passport no: EC1174633 Issued at (DFA Manila) Issued on (May 22 2014)

Expiration date (May 21 2019)

Seaman book: C0415848 Issued at (Manila) Issued on (March 25 2015)

Expiration date (March 23 2020)

Character references:

Occupation Address Contact no.

Edgardo Bacalla (OFW) Bohol Philippines +639*********

(Mech.tech.)

Marcos Chico (HR/office) Bernhard Schulte Ship Management. +639*********

BMS house, 1965 Leon Guinto Malate Manila

Marlon Marisigan (OFW) Quezon City. +639*********

(Mechanical Technician)

I do solemnly swear that the above information is true and correct based upon the best of my knowledge.

JILBERT G.VILLANUEVA



Contact this candidate