Ray Elshout, PE
PROCESS ENGINEERING 626-***-**** (Cell), 626-***-**** (Direct)
*** *. ** ******, ********, CA 91106 E-Mail: ac50x0@r.postjobfree.com
Process Engineering /Project Engineering
Fields of Services Offered:
Refinery Design Through Schedule “A” Packages
Process simulation ( HYSIS & PRO II)
Heat Pinch Technology
Licensor Engineering Packages
Economic Optimization Studies
Revamp and Debottlenecking
Gas Treating including most solvent systems
Mechanical Process including P & ID’s, Hydraulics and Relief Valves
Operating Manuals and Hazop reviews including safety studies
Expertise & Experience:
Over 20 years of experience and expertise
oRefineries
oGas Processing
oSulfur Recovery
oEnergy Audits and Heat Pinch Technology.
oEnvironmental Engineering Including Waste Water Treatment
oHeat Exchanger Network Simulations and Pinch Technology
Refinery Expertise
oCrude and Vacuum Units
oDelayed Coking
oHeavy Oil Desulfurization
oCatalytic Reforming
oFCCU and Unsaturated Gas Plants
oIsomerization including Butamer and Light Straight Run Gasoline
oHydrocracking
oGasoline Blending
oMaking Low Sulfur Sulfur Gasoline and Ultra Low Sulfur Diesel
oHydrogen and Synfuels
oAlkylation both HF and Sulfuric Acid
Engineering from Start to Finish
oConcept Development
oProcess Simulation Including PRO II and HYSIS
oPFD’s
oP & ID’s
oEquipment Specifications
oMetallurgical Recommendations
oHydraulics including Line sizing
oInstrumentation Specifications
oStart Up Assistance
ADDITIONAL KEY AREAS OF EXPERTISE
Project Engineering
Debottlenecking
Off sites
Field Engineering
Equipment Rating
Tankage and transfer
Cap[ital. Cost Estimating
Utility Systems
Blending of gasoline and diesel
Work Experience
Process Consultant at Energy Systems Engineering, Pasadena, CA 01/2010 – Present
Process Engineering Design of refining and Petrochemical Facilities. Utility : Evaluations of Steam and Cooling Water, Flare gas recovery for California CARB Rule 1188,Revamps and debottlenecks, Waste Water Treating to remove PCE, TCE and Hexavalent Chrome, Nerve Gas Destruction Program for DOE, Used Motor Oil Reprocessing Plant to produce High Viscosity Index and Water White Lube Blend Stock by Hydrotreating
Principal Process Engineer, TETRA Engineering and Technology, Fullerton, CA. 01/1996 – 01/2010
Process engineering lead on revamps and debottlenecks of Crude Unit, Vacuum Unit, Aromatics Fractionation Unit, Vacuum Residuum Desulfurization, Low Sulfur Diesel Desulfurization and Gasoline Blending Facility Using Near Infared Technology. West Coast Marketing Director
Principal Process Engineer KTI, San Dimas CA (now Technip) 10/ 1988 – 01/ 1996
Process design of Hydrogen and synfuels facilities. Developed operating manuals for new designs. Evaluated producing bottle grade carbon dioxide from purge gas from a hydrogen plant PSA Unit. Process simulations PFD’s, P & ID’s, Equipment specifications, equipment layouts, equipment sizing and specifications.
Economist Santa Fe Braun, Alhambra California 06/ 1995 - 10/1 988
Performed economic evaluations and determined optimum configurations for refinery development in pre-engineering phase. Develop block flow diagrams, overall yields, did product blending, estimated utility usage, did factor cost estimates. Projects including upgrading European refinery for lead free gasoline, overall design concept for Korean Refinery, Optimization of ethylene furnace heater tube configuration for maximum yields, training program for Powering Refinery Lead Operators and developed new operating manuals..
•
EDUCATION AND CREDENTIALS
BS and MS Chemical Engineering from the University of Michigan.
UCLA Extension Studies in Project Management and Environmental Engineering
Registered Chemical Engineer California CHE 2868
Author of multiple technical papers including processes to make low sulfur fuels
US Patent 5,120,517 “ Process for the Removal of Sulfur Oxides and Nitrogen Oxides from Flue Gas”
Available for Travel or Relocation
References Available upon Request