Electrical Engineering Microsoft Office
Resume:
Devin Fung 909-***-**** Page * of *
DEVIN FUNG
**********@*.****.*** www.linkedin.com/in/devinfung
SUMMARY
UCLA student majoring in Electrical Engineering. Experience with circuitry, programming in Matlab, Arduino, C++, and AutoCAD Electrical. Strong team player with leadership skills, high adaptability, and works with composure under high stress environments. Thrives with mentorship and constructive criticism. Dedicated to learning and resourceful in problem solving. Full focus now on new internship or job of Summer 2018. KEY SKILLS
Circuitry Matlab and C++ AutoCAD Electrical
Arduino Resourceful problem solver Eager to learn
Dedicated Committed Team Oriented
Respectful Open to constructive Criticism Verilog
NI ELVISmx Labview HSPICE
PASCO
MyDaq (Oscilloscope, digital multimeter,function generator, bode generator) Analytical Strong interpersonal skills
EDUCATION
Cumulative College GPA: 3.35/4.00
Mount San Antonio College, Walnut, CA 2012 – 2014
Transferred to UCLA
Courses Completed:
Physics 4A Engineering Physics Physics 4BEngineering Physics Physics 4CEngineering Physics Math 181 Calculus and Analytic Geometry Math 285 Linear Algebra and Differential Equations Math 280 Calculus and Analytic Geometry University of California Los Angeles, Los Angeles, CA 2014 – 2015, 2016 – Present Bachelor of Engineering in Electrical Engineering, expected Fall 2018 Courses Completed:
EE102 Systems and Signals EE 101A Engineering Electromagnetics EE 131A Probability and Statistics EE 102B Principles of Semiconductor Devices EE 10/11L Circuit Theory 1/Circuits Lab CS SCI 31 Intro to Computer Science EE M16 Logic Design - Digital Systems EE 101B Electromagnetic Waves EE 141 Principles of Feedback Control EE 170A Principles of Photonics M185 Introduction to Plasma Electronics EE 163A Introductory Microwave Circuits Courses in Progress:
EE 173DA Photonics and Communication Design EE110/111L Circuit Theory 2/Circuits Lab EE 141 Digital Signal Processing CS SCI 32 Intro to Computer Science II LABORATORY
Undergraduate Laboratory
UCLA, CA 2016 – 2017
CMOS and CDC cameras with ImageJ
Devin Fung 909-***-**** Page 2 of 3
LABORATORY (cont’d)
Took multiple long exposures of diffracted lasers under low light conditions and analyzed different methods of measuring spot sizes.
One of the traditional methods was to scan the Gaussian beam through a slit, but the procedure takes too long and is very sensitive to the scanning path across the beam.
Another method was called the straight knife edge where the spot size was calculated from variations in photo detector ouput power. However, the scanning the beam at a uniformly constant speed.
The last method was finding the ratio of minimum output power to the total power of the Gaussian beam when an opaque ribbon is scanned across it. This method proved to be the simplest and fastest method in calculating the spot size.
Pictures were normalized using ImageJ to remove the offset. In addition, we were able to measure spot size of the laser from just the image.
Observed the limitations of CMOS and CDC cameras due to temperature fluctuations. Ion –Mobility Mass Spectrometry
Using a spectrometer, we measured the intensity, absorbance, transmittance, and fluorescence with the PASCO software
We then tried to identify different objects by observing the light spectrum and comparing them to already known spectra.
Observed the spectra of Helium, Hydrogen, and Deuterium and recorded the distances to observe the differences in wavelength of light and the intensity of each color. C++ Game Design
Built a game world using inheritance to design protagonists and enemies. Each protagonist was part of the same team, but had his or her own special skills. Similarly the enemies were part of different teams, but shared common traits within each of their teams.
Implemented a maze solver using both stacks and queues that would go from the start and add in adjacent open spots to the queue or stack.
Built a miniature garage door with a light sensor
• Used Arduino to program a garage door that opens using a motor driven spool. Once a car/object interferes the light sensor, the garage door will be on open mode. If the laser stays connected to the receiver, the garage will be on off mode.
• The garage was programmed to close automatically after 5 seconds (off mode) if the laser connects to receiver.
Micromouse
• Used a PCB with 5 sensors connected. One sensor in the front and two sensors on each side.
• Differential drive system with two driver wheels and one castor wheel. The castor wheel is positioned so that the centroid of motion remains at the center of the micromouse.
• Arduino was used to program the micromouse. Used the Wall follower algorithm where the micromouse makes every right turn possible until the goal is reached. EE 111L/EE 10L
• Built RLC circuits on a breadboard in lab and observed the behavior on NI Elvismx oscilloscope as different AC/DC voltages were input using the NI Function Generator.
• Time domain and frequency domain analysis of RLC circuits and plotted using Bode plots on MyDaq
• Observed electrical impedance with varying amplitudes an relative phases. Strategist and Coach
Devin Fung 909-***-**** Page 3 of 3
CSGO eSPORT 2015 –2018
UCLA Team
Coached the UCLA team in CSGO at a professional level. Balanced school work and training with the college team to improve skill and develop strategy. Key role was an in-game leader for a 5-man team.
Won 3rd Place in Collegiate Starleague Grand Finals in Canada in 2017
Won 4th Place at 5K Esports Arena CSGO:Open
Won 1st Place at Beachcon in 2016
Professional eSport and ESEA 2012 – 2016
Took a 1-year hiatus from UCLA studies to pursue the eSport professionallydue to difficulties in balancing school work and scheduled training.2015 –2016
Collaborated with multiple teams to train and develop strategy. Trained 80-hour weeks.
Played at a Premier level on ESEA under Savages, an Esports team and sponsor. Private Tutoring 2012 – 2016
Algebra 1, Algebra 2, Geometry, Trigonometry, Calculus 1, Calculus 2, Calculus 3
Physics AB Mechanics, Physics BC Electromagnetics PRESENTATIONS, AWARDS and HONORS
3rd Place at Collegiate Starleague Grand Finals 2017 4th Place at 5K Esports Arena CSGO: Open 2015
1st Place at Beachcon 2016
2nd Place at ESEA Intermediate 2017
5th Place at ESEA Main 2017
2012 International Baccalaureate Diploma 2012
TECHNICAL SKILLS
Software& Instruments AutoCAD Electrical, Matlab, Verilog, C++, Microsoft Office (Excel, Word, PowerPoint), MyDaq (Oscilloscope, Function Generator, Digital Multimeter), ImageJ, CMOS camera, CCD camera, Labview, NI Elvismx, Spectrometer, PASCO Languages Arduino, C++, English (native), Cantonese (advanced), Mandarin (beginner) REFERENCESPROVIDED UPON REQUEST
Contact this candidate