PATRICK J. GREENE

Address: *** ******** **.

Channelview, Texas 77530

Phone: 281-***-****

Email: ac2esq@r.postjobfree.com

OBJECTIVE: To gain employment at the intermediate to advanced level of non-destructive testing and/or quality control/quality assurance. I intend to advance through hard work and dedication to be a valued and skilled employee.

TECHNICAL The Ocean Corporation, Houston, TX

EDUCATION: June 2007 – February 2008

-- ASNT Level II Academic and Level I Practical

in:

- Visual I, II and Leak Testing

- Penetrant Testing

- Magnetic Particle Testing

- Ultrasonic Testing

- Eddy Current Testing

- Radiographic Testing

-- Radiation Safety (NRC 40-Hour Course)

-- Hazardous Material (USDOT 40-Hour Course)

-- Rigging (API RP2D)

-- American Red Cross - First-Aid/CPR/AED

-- American Heart Association-First-aid/CPR/AED

Tuboscope NOV, Houston, TX

July 2007 – August 2007

-- Level II Academic and Practical in:

- Ultrasonic Testing (Shearwave)

- Basic Inspection Technology (BIT)

- Special End Area (SEA) Thread Inspection

Oceaneering Inspection, Houston, TX

April 2008 – September 2009

-- Level I Academic and Practical in:

- Heat Treatment/Stress Relief

-- NCCER Certifications in:

- Conduct Annual Cathodic Surveys

- Inspect Cathodic Protection Rectifier

- Prevention of Atmospheric Corrosion

- Measure Wall Thickness of Pipe

- Application and Repair of External Coatings

- General Abnormal Operating Conditions

-- TWIC Carded, SAFEGULF, Offshore Water

Survival, Confined Space, Basic Plus, N.O.R.M.,

H2S, Project Management Concepts Training, Data

Recorder Training/Experience(API RP2A),Topside

Inspector Training/Experience (API RP2A),

Erosion/Corrosion Technician Training, Level

II UT, MT, PT, VT Technician and RT Trainee

Bureau Veritas Apprentice Inspector Program

Graduate

One CIS ("Bill Tillman") ASME Section VIII, IX

and V Training Seminar

ASME PCC-1 CERTIFIED Bolting Technician/Joint

Integrity Inspector

Work Experience:

8/23/2017 to Present

Center Point Energy – Chief Pipeline Construction Inspector 6/18/2017 to Present

Catahoula Consulting,Inc. – Contract Inspector

Shell – Vessel Off-load Inspector

9/08/2016 to Present

Microalloying International, Inc.-Contract Inspector Plains All American Pipeline – Watonga to Cashion - Lead Coating Inspector

Plains All American Pipeline – Watonga to Cashion – Lead Off-load Inspector

Enlink – Jafar Re-Route Project – Lead Coating Inspector EPCO – Pipe Condition Assessment Inspector

Enlink – Horned Frog Lateral- Load-out Inspector

Queststar – Load-out Inspector

Enlink – Frog-leap Project – Lead Coating Inspector Enlink - Chickadee Gathering and Transmission Project – Support/Load-out Inspector

EPCO - Texas City Line #26 - PGP Expansion – Receiving Inspector

11/01/2014 to 01/01/2016

Bureau Veritas North America - Energy Services Inspector 2nd/3rd Party Inspector (Subsea Umbilicals, Valves(ball, butterfly, relief, bleed and block, gate), pumps, rotary equipment, drilling/completions equipment, pressure Vessel inspection, heat exchanger surveillance (TEMA/ASME),

(Company Inspector-Total-Egina Project-(Umbilicals),

(Certifying Authority- Total-Kaombo Project- Umbilicals),

(Pre-Commissioning Third Party Inspector-TULLOW TEN Project), HPU inspection, Flare system inspection, Flex- pipe inspection, SIT flex-pipe/QCDC, hydrotest witnessing, leak test witnessing, pneumatic test witnessing, various skids, seals, packers, BHA's, BOP, SURF, Pipe (casing, line pipe, drill pipe and pup pipe), Expediting, hardness testing surveillance, lab testing surveillance, MTR review, Data Book/Document Review, third party coating surveillance

(pipe, valves, subsea hardware, drilling and completions equipment), Report Writing, Shell(Carmon Creek project – Shell pipeline and valve coating inspector, Shell MARS A Upgrade- coating inspector, Shell Nakika Coulomb Phase II – Coating Inspector, Coating Inspector Al Anbar project, Coating Inspector for the ADCO project, Third party coating inspector at Labarge coating and Womble Company for Chevron and Exxon Mobil pipeline.

05/01/2014 to 10/01/2014

North Shore Steel - QC Inspector

Performed visual and dimensional inspection of burned parts per customers’ specifications and purchase order

requirements. Performed lay-out of plate steel to be rolled into cones and cylinders for pressure vessels. Performed visual and dimensional inspections in-process of cones and cylinders, including visual weld inspections of cones. Performed hardness testing - Brinell hardness testing. Quality inspector on (Smith Tank Project). Initiated and resolved NCRs. Completed reports at the end of each shift. 01/01/2012 to 03/01/2012

WSP HOUSTON OCTG,Inc - Level II UT/EMI Prove-Up/SEA Inspector

Level II UT prove-up Inspector (UTT, Shear wave). Set-up, calibrated and operated manual UT thickness gauges and flaw detectors for prove-up of automated UT/EMI indications on pipe and casing, to determine flaw characteristics and acceptability based on API standards ( 5CT, 5L, etc) and customer requirements. Performed dry magnetic particle inspection (yoke), as a prove-up to UT. Performed wet fluorescent magnetic particle inspection with black light on plain and threaded end pipe. Performed thread

inspection.

09/01/2010 to 10/01/2011

SSAB - Lead Quality Inspector

Lead inspector for a 7 inspector team covering two shifts for SSAB "Green Plate Project". Provided quality and safety training to inspectors. Input reports into the QMS. Performed visual and dimensional inspection of plate steel for conformance to customer specifications. Initiated and investigated NCRs. Operated Burney 10 plasma machine for special orders. Operated overhead cranes (5 to 50 ton) and forklifts to move plate in and out inspection area. Perform coating(various coatings) inspection of speciality products. Packaged plate for shipment overseas (vessel load out and unload). Green plate coating inspection.

02/01/2010 to 09/01/2010

Tenaris Subsea Center - Level II UT/ET Inspector

Set-up, calibrated and operated automated UT and ET units online (mill) and offline for coiled tubing (SS duplex) inspection. Set-up, calibrated and operated manual UT flaw detectors (shear wave) and thickness gauges for prove-up of any indications from the automated units. Performed liquid penetrant and X-ray testing of indications and orbital welds. Perform hot dipped galvanizing of duplex coil tubing and inspection. Shell Oil Co.- Popeye/Europa Project 04/01/2008 to 09/01/2009

Oceaneering Inspection - Inspector

Data Recorder/Underwater Inspection(API RP2 WSD), NDT Level II Inspector (UT, MT, PT, VT,ET,RT), Topside Inspector (API RP2A) Erosion/Corrosion Technician, Heat Treatment/Stress Relief Technician (Oven and ceramic), P&ID, TWIC, HUET, Rigpass, SURF inspection, Topside and subsea inspection trainer. Conduct Annual Cathodic Surveys, Inspect Cathodic Protection Rectifier, Prevention of Atmospheric Corrosion, Measure Wall Thickness of Pipe, Application and Repair of External Coatings, General Abnormal Operating Conditions, coating inspection (variety of coatings) of marine offshore structures, pipelines, risers, subsea equipment/hardware, coating repairs, Assessment of subsea umbilicals, risers and flowlines coating and cathodic protection, Instructor for coatings assessments on pipelines, apertures, and structural assets. Vessel loadout and unload of pipe for pipelines and risers. Performed topside coating inspection of more than 2,200 offshore platforms. Coating Inspector for Chevron GB-236 A, Coating Inspector for Anadarko Independence Hub, Coating Inspector for ENI Devil’s Tower, Coating Inspector for Exxon Mobil EI-314BP.

10/01/2006 to 02/01/2008

Tuboscope NOV - Level II UT Inspector

NDT Level I and II Prove-up Inspector (Automated & Manual shear wave) of pipe and casing. Borescope Visual Inspection

(Pipe ID), drift testing, Rockwell hardness testing, dry magnetic particle inspection (YOKE), Special End Area (SEA) inspection, Thread inspection. Coating inspection and repairs. Report writing.

04/01/2003 to 09/01/2006

Producer's Rice Drier, INC - Lead Drier Operator/Supervisor Supervised a team of operators and laborers. Intake and shipment of farmers’ rice. Performed drier processes to clean and dry local farmers rice and soy beans. Performed drier operations including operating conveyor systems, auger systems, bin selection based on dryness, sample testing, fumigation, safety training and customer

interaction.

01/01/1988 to 02/01/2003

Disability Associates, Inc. - Disability and Personal Injury Consultant

Represented SSI, SSA, RR and VA claimants on disability claims. Consulted with Attorneys and Law Firms as a SME (on Disability) and served as an expert in trials.

11/01/1986 to 11/01/1987

National Pipe and Tube (Allied Tube and Conduit)

Cut-off/Saw Operator on the finishing floor. I set-up the machine with cutting tools, chucks for the pipe size, grease the machine, regular maintenance, sawed of the ends of pipe and beveled those ends, used micrometers to determine tolerance of bevel, cleaned work area, adhered to safety policies and procedures for machine operation. 08/01/1983 to 10/01/1986

United States Marine Corps- DIVISION UNITREP NCOIC Primary MOS was 0341 (mortarman). I served on special duty as a recruiter. Unit Status and Identity Report (UNITREP) NCOIC 2d MARDIV., Deputy Chief of Staff, Readiness. I was the division inspector for unit readiness.

Education & Training:

The Ocean Corporation Diploma

ASNT Level II Academic and Level I Practical in: Visual I, II and Leak Testing, Penetrant Testing, Magnetic Particle Testing, Ultrasonic Testing, Eddy Current Testing, Radiographic Testing, Radiation Safety (NRC 40-Hour Course), Hazardous Material (USDOT 40-Hour Course), Rigging (API RP2D), American Red Cross - First-Aid/CPR/AED, American Heart Association - First-Aid/CPR/AED

San Jacinto College A.A.S. Degree

NDT, QA/QC, welding, API coursework

Certifications & Achievements:

AWS, ASNT, ASQ, SUT

Skills: Proficient in Word, Excel, PowerPoint, SAP, QMS, API Monogram, 132 hour Safety Professional Training

(Occupational Safety and Health Academy)

REFERENCE: Available Upon Request

Contact this candidate