Engineering Technician

HY T. NGO

**** ***** ***. *** ****, CA ***** * Cell: (408) - 439 – 5836 * Email: *********@*****.***

OBJECTIVE

Seeking a challenging Engineering Technician/Engineer position.

EDUCATION

B.S in Computer Engineering, San Jose State University, CA, 2004

SKILLS

Experienced test 40G/100G optical transceiver and Optical Time-Domain reflectometer (OTDR).

Experienced built of complex system, fabrication, integration, calibration, alignment and testing set up high complexity electro-mechanical equipment in the clean room environment.

Experienced testing of complex Wireless Devices such as IQxel and IQxstream,.

Performed reliability and validation test for Electro-Optical products.

General lab support tasks such as set up equipments, maintenance and calibration.

Ability to failure analysis using ATE and software IQramp.

Basic understanding of digital and analog circuits.

Able to troubleshoot from component level to circuit boards level.

Familiar with software such as Linux, DOS and IQramp analysis.

Ability effective worked independently with minimal input from others.

Familiar with Signal Generator, Network & Spectrum Analyzer, Power meter, Power sensor, VOA, BERT, DCA, OPM, Optical Switches, Thermal Stream, HASS/HALT chamber.

EXPERIENCE

02/2016 to 05/2017: II-VI Photonics Inc, San Jose, CA.

R&D Engineering Technician

Evaluated high speeds 40G/100G Optical Transceiver (40G-LR4, 100G-SR4 and 100G-CWDM4), Nanoamplifier and Optical Time-Domain Reflectometer (OTDR).

Conducted experimental test to collect test data and provide data analysis.

Worked closely with design engineers to development activities typically in optical test set-up, calibration, alignment and assembly/built prototype of components.

Perform lab tests relevant to production development to identify the root cause.

Responsible for a wide variety of engineering support tasks typically the fields of Electronics, Mechanical and Electrical engineering.

01/2007 to 10/2015: Sanmina Corp, San Jose, CA.

Electro-Optical & RF Engineering Technician

Worked closely with engineers, assist in building simple prototypes and testing Wireless Devices such as IQxel, IQxel-M, and IQxstream.

Worked collaboratively with R&D and production departments to develop, test and implement processes.

Help create, setup, calibration and testing with validation engineering execution plan for all areas focus related to new product qualification.

Performed operational test and provide support for test engineering with failure analysis base on electrical data for fault isolation.

Performed test validation and reliability on Electro-Optical products.

Help engineering activities: collect data, perform basic data analysis and generate reports.

Performed flash firmware on Optical 40G transport modules and testing inside HASS/HALT chamber using LINUX and DOS base software.

Worked in Environmental Stress Screening (ESS) facility with engineers, test and support engineers for system level trouble-shooting 40G modules installed in OTS line card system.

Performed system validation pilot production testing on 40G transport modules, in addition, testing Burn-In in thermal chamber in manufacturing for Optical-40G transport module.

Used Excel to collected test data to report product yield.

Remarkable to maintain and calibrate lab equipments and/or test equipments.

Worked independently with minimal supervision as well as in a team environment

08/06 to 1/07: KLA Tencor Corp, Milpitas, CA

Electro-Mechanical Engineering Technician

Worked high complexity electro-mechanical assembly; wire, alignment and adjustment close tolerances.

Performed set up, integration, calibration, and final testing robotic system for wafer inspection equipment in the clean-room environment.

Worked with mechanical and test engineers to ensure machine properly functionality.

Troubleshooting and repairing components and/or instruments.

09/2004 to 10/2006: Intel Corp, Newark, CA

Electro-Optical Test Technician

Worked and understood of environmental test thermal chambers.

Tested and tunable transceiver modules (300 pin) using lab equipment.

Performed calibration, setup, troubleshoot and test support for RMA units.

Characterization of devices, include measurement of eye diagrams, jitter and BER.

04/1999 to 10/2002: Hunter Technology, Inc. Santa Clara, CA

Test Technician

Worked ICT type testing, (Takaya APT-84cj) Setup, run & debug failure boards.

Performed Probe Test on MicroCraft machine, Software EMMA 2000.

Strong knowledge of wafer process, assembly, wet chemical etch and lapping for cleaning or remove materials.

03/1997 to 04/1999: Memry Corp, Menlo Park, CA

Test Technician

Ability to trouble-shooting and repaired on production machines.

Performed powder coating, seam welding machine & final product test.

01/1995 to 03/1997: Solectron Corp, Milpitas, CA

Test Technician

Performed functional test at system level.

Diagnosed and used ICT machine HP 3070 to final PC test.

STRENGTHS: Hardworking, attention to detail, careful lab work, fast learner and ability to multi-task.

Citizenship: U.S Citizen

Contact this candidate