Quality Control Software
Resume:
Pesilio Feliciano
Lorain, OH 44052
Objective:
To secure a full time position with a growing company that values a strong work ethic, attention to
detail and a "Can Do" attitude!
Experience:
Norman Noble Inc. – Highland Heights, OH
Quality Control Inspector II: August 2011 to May 2013
Inspect different types of bones screws for various companies that go into the human body.
Measuring devices used – micrometers, calipers, profilometers, blade micrometers, pin gages, thread
Gages, etc. Programmed a Smart Scope (vision system) using customer blueprints to assist operators.
. Also worked directly with all machine operators, Deburrers and Engineers. Assisted with all three shifts.
Presrite Corporation – Cleveland, OH
Layout Technician: October 2010 to August 2011
Inspect different type of gears using various measuring devices such as calipers, micrometers, plug
Gages, thread gages, etc. Also use 3 different CMMs to inspect: 1) Zeiss Accura with Calypso software.
This has scanning capabilites with a rotary table. I’m sufficient in programming this CMM. 2) Zeiss UMM
550 with UMESS software and 3) Mitutoyo Bright CMM. I’m training to program the last two CMMs, but
I can operate both with no supervision.
Empire Die Casting Co., Inc. – Macedonia, OH
Quality Technician: March 2010 to October 2010
Inspect aluminum and zinc parts made at Empire Die Casting Co., Inc. Program a Zeiss (Spectrum)
CMM (coordinate measuring machine) with Calypso software. In charge of SPC and first piece articles
And layouts. Also use various other instruments: height gage, pin gage, thread gage, dial bore gages,
Optical comparator, hardness tester.
Impact Industries - N. Ridgeville, OH
Quality Inspector. February 2008 to March 2010
Inspect in-house parts from several different types of presses. Program a Zeiss (Vista) CMM with
Calypso software. Also use various instruments such as height gages, pin gages, calipers,
micrometers, depth micrometers, optical comparator, Rockwell Hardness Tester, thread gages.
Use blueprints to inspect all components. Received Jurasin Certification as an Internal Auditor –
ISO 9001:2000. In the process of updating to ISO 9001:2008.
Smith & Harris Machining (through temp service – Search Master, Inc.)
Quality Inspector – December 2008 to February 2009
Inspect components for the mining industry such as gear cases, track frames, main frames and
butt plates. Used a Sheffield CMM. Also used blueprints to inspect all components. Used
calipers, micrometers (internal and external), depth gages, thread gages, plug gages and so one.
Took care of updating all files, paper or database.
Impact Industries (through Ameritemps) N. Ridgeville, OH
Quality Inspector. November 2007 to December 2008
Inspect in-house parts from presses. Used a Zeiss (Vista) CMM with Calypso software. Also
used height gages, pin gages, calipers, micrometers, depth micrometers, etc... Used blueprints
to inspect all components. Received Jurasin Certification as an Internal Auditor – ISO 9001:2000
Started through temporary service and got hired in February 2007.
Nook Industries - Cleveland, OH
Quality Control Inspector. April 23, 2007 to October 19, 2007
Inspect linear components for Jack Screws and different gear components. Used blueprints,
gages and other instruments to verify parts. Received certification for programming a Zeiss CMM
with Calypso software.
Varbros (through Area Temp Service in N. Olmsted, OH) Cleveland, OH
Quality Inspector. 1/07 to 2/07. Inspect in-house parts off of presses. Parts mainly used on oil
filters. Used Zeiss CMM and used other measuring devices such as height gage, calipers,
micrometers, GO/NOGO plug gages and thread gages. Used blueprints to inspect all
components. Through Area Temp Service.
RW Beckett Corp. North Ridgeville, OH
Quality Analyst - ASQ Certified July 1, 1996 to December 29, 2006
Mechanical Inspector
Worked in 3 different areas:
1.) Receiving Inspection - Used different measuring machines such as a Coordinate Measuring
Machine (CMM) and a Vision System. Wrote different measuring programs using blueprints for
both the Mitutoyo manual CMM and the vision system. The CMM is used to program 3
dimensional parts and the Vision System is used to program 2 dimensional parts. Also used
other mechanical measuring devices such as calipers, micrometers, height gages, pin
gages...etc.
2.) Audit - To inspect finished goods in the assembly area. Also did some torque training for a
couple of years when new lines were ready to begin.
3.) Return Goods - To analyze return components such as oil burners, pumps, motors, controls
and igniters. Coordinated 2 special company projects (Kaizen events) leading toward ISO 9000
certification.
Assembler September 29, 1993 to June 30th, 1996
Worked in the sub-assembly area. Assembled parts for the different oil burner lines. Also worked
in the machine room in the housing cell. This is where different machines were used to assemble
the housing used for the oil burners. Machines included were a boring machine, riveter and a drill
press.
Education:
Inspection Engineering – Westlake, OH – 2007 Certificate of Completion in Operating and programming a
Zeiss CMM with Calypso software.
Optical Gauging Product - New York Vision System training 2000
Lorain County Community College ASQ Certification
Certified Mechanical Inspector 1999
Mitutoyo - Michigan
Coordinate Measuring Machine (CMM) training 1996
Lorain County Community College Elyria, OH 1984-1986
• Main - Computer Systems Technology
• Served as president of Los Unidos for 2 years (1984-1986)
• Special recognition - Who’s Who among Jr. College Students
• Math Major in College (up to physics)
Admiral King High School Lorain, OH
Diploma: 1974-1978
Advance student. Main studies were in math.
References:
United Way Day of Caring (Event President - 2003-2004)
Sacred Heart Volleyball / Basketball Coach (2011 to present)
St. Peters Girls Basketball Coach (2004 - 2011 Grades 4-8)
St. Peters Girls Volleyball Coach (2006 - 2011)
Softball Coach (Men's/Co-Ed) 1996 - present
Corporate Challenge 1993-1995 (Swimming, Track & Field Basketball)
Festival/Special Events Committee organizer – Sacred Heart Chapel and St.
Peters Catholic Church. Both in Lorain, OH.
Special Skills:
Bilingual fluency in Spanish
Familiar with: MS Word, Excel, PowerPoint, Visio, blueprint reading.
Certified in gauging - manual calipers.
Proficient in programming Vision Systems from Optical Gauging Products
Products from Production Services (gage calibrations).
Proficient in programming Coordinate Measuring Machines (CMM) from
Mitutoyo (manual only) and Zeiss with Calypso software CMMs.
Calibrated different gages on a monthly basis following the proper
procedures from the Quality Handbook Reference Guide.
Certified Forklift Driver since 2003 (RW Beckett Corp.)
Personal References:
Susie Wolf: 440-***-****
Jim Powers: 440-***-****
Jesus Perez: 440-***-****
Contact this candidate