Electrical Design Engineer, Management Engineering, Control Engineer

Ameen S. Shakir

*** ****** *****, *******, ** ***62

***********@*****.***

Tel 440-***-**** (USA)

PROFESSIONAL SUMMARY

Engineering Industrial Management, Electrical and Control Engineer with

experience in power plants, Gas Turbine'' LM2500, LM1800, LMS100, LM6000''

and solar energy, seeking an engineering position in construction

management, power and lighting distribution design.

PROFESSIONAL EXPERIENCE

General Electric AERO DERVETIVE; Greenville, MAY 2012 -Present

Project Management and Electrical Engineer Support providing Aero Design

Development Team for Support LMS 100, LM6000 and LM2500

Analyze and review functional circuits using GE Design Practices and

GE Aero TRMs

Analyze cable selection; interface location routing, cable segregation

and voltage drop calculations.

Certification analysis to confirm components selection satisfy global

and local code requirements, such as NEC, ANSI, CSA, CE ATEX, AUS,

DNV and Lloyds.

Develop One Line and Three Line Diagrams, Wiring / Schematic Diagrams,

Loop Diagrams, I/O Lists, Cause and Effect Lists, Fabrication and

Assembly Arrangements associated with Turbine Control Panels and

Terminal Boxes, Cable and Instrument Layouts, Hazardous Area Layouts,

Battery Systems and the specification of associated equipment

Support design reviews and the Tollgate process

Design Hima panel, Motor Control Center (MCC) Edit the TECH SPEC

for it.

Point to point check from the instrument to the PLC

Edit Bill of Material (BOM)

Using Enovia Software to Product Lifecycle Management.

Diebold; Los Angeles, CA Feb

2012 - March 2012

Project Manger internship

Managed 3 groups consisting of 5 members each

Managed the time and the quality of work

3 Prong Power; Berkeley, CA

Electrical Engineer Internship

August 2009 - Feb

2010

Installed entire PHEV system into hybrid cars

Supported development of conversion kits

Collaborated with head electrical engineer and founder of company to

develop and install hybrid kits

General Electric Energy; Schenectady, NY

July 2008 - October 2008

Control Engineer Trainee

Completed an intensive Gas Turbine MarkVI, and Alan Bradley control

direct hire training program

Gained experience in HSE, Frame 9E and Frame 6 mechanic details,

generator control and protection, and turbine control using the Mark

VI Distributed Control System

Completed certification as a Technical Adviser (TA) to install and

commission GE units

Conducted configuration, programming and troubleshooting of the MarkVI

Distributed Control System for proper control of Frame9 and Frame 6 GE

gas turbine generators.

Work on block diagram software Program (M6B FILE).

The Baghdad Company for Gas Turbines; Amman, Jordan

April 2007- March 2009

Control Engineer

Conducted the electrical and instrumentation design of Al-Qudus power

plant extension project funded by the United States sponsored Gulf

Region Division. This included instrumentation specifications using

ISA20 spec. sheets, hookup drawings complete with BOQ. Full details

were approved by the senior engineer and approved by the owner

engineers Parsons and later SBH.

Responsible for electrical and lighting power design, building

lighting analysis, lighting utility and process power design, cable

routing design, and instrumentation selection. Dialux software was

used to design the lighting for the shaded, buildings and outdoor

areas. Cable routing designs were produced using Auto CAD with BOQ.

Responsible for specification and hookup designs. Specifications for

pressure, flow, temperature, level, etc. were generated using ISA

standards. Hookups were represented using Auto CAD and Excel with

applicable ISA standards.

Using Auto CAD for designing electrical 2D drawings like one

line diagrams/ three line diagrams for auto voltage regulator.

Utilized ETAP to perform short circuit, voltage drop, load flow, motor

starting, and transient stability coordination study for low voltage

systems.

Performed lighting design and calculation using AGI lighting program.

Served as technical advisor for team of four control engineers. The

advisor office was in Amman with a team of GE TAs while site engineers

were in Baghdad Qudus Power plant. The team was aided with seven web

cameras to supervise and advise.

Eye Specialty Hospital for Ophthalmology; Amman, Jordan

January 2007 - April 2007

Electrical Engineer Internship

Responsible for bi-monthly maintenance of the Allegretto Machine which

required full knowledge of the machine electrically, optically and

mechanically

Responsible for the daily calibration of the Allegretto Machine, which

required operational knowledge of the system under a senior supervisor

engineer.

EDUCATION

Master in Manufacturing System Engineering and Management

2012

California State University of Northridge; Northridge, CA

GPA: 3.6

Courses taken include: lean manufacturing, statistics, engineering

economics, finance, innovation engineering management, and operation

research

Bachelor of Science in Electrical Engineering 2006

University of Technology; Baghdad, Iraq

Concentrations: Audio visual communication, engineering and numerical

analyses, advanced electronics, electromagnetic fields Communication and

signal processing, control, electrical machines, and power system

SKILLS

Experience in electrical and lighting design, cable routing and

instrumentation design

Training in solar equipment installation

Knowledge in automobile hybrid conversion systems

Proficiency in English and Arabic

Proficiency in Matlab, Auto CAD with full internet capability, and

gEDA Software

Experience in Mark VI Distributed Control System.

Enovia Software.

Understanding of Middle East markets and culture.

LANGUAGES

Arabic - (Interagency round table Level 3)

English - (Interagency round table level 3)

Contact this candidate