Quality Assurance Control
Resume:
Mildred Salery
abogf7@r.postjobfree.com
Birmingham, Al 35242
Experience
May 2004 – January 2013
Honda Manufacturing of Alabama
Lincoln, AL
Process Associate
Build Honda Pilot SUV, Odeyess Vans, Accord, Ridgeline and Acura using hand tools, air guns, load assist, torque wrenches, dial wrenches, dc tools and a computer.
Assemble
•Bolt IP(Instrument Panel) to Body
•Install Heater Hoses, Cargo Hook Screw and Side Liners, Slide Rails, Speakers, Weather Strip, A and D Pillars, Tail Lights, Side Step and Rear Step Garnishes, Seatbelt Caps, Drain Plugs and Grommets, torque and mark Hac Pipes, torque Seatbelt Bolts (D Pillar), Install D Pillar Garnishes, Install Coat Hooks, Map Lights, Door Seals and Sub up License Garnishes.
•Connect center couplers from IP to Body.
•Perform Quality Check
•Tap Out Cross threads and do other repairs.
May 2003 - May 2004
ACCI (Automotive Containment and Consulting, Inc.)
Lincoln, AL
Inspector
Inspect automotive parts for defects described on the OP Standard and fill out all necessary paper work.
August 2002 - January 2003
Talent Tree (Mercedes Benz)
Vance, AL
Production Worker
•Conveyance- Pulled and staged parts from stock using Broad Cast Sheets, tuggers, upright forklifts and delivered them to the production lines. Removed empty containers from the production lines and returned them to the staging area.
•Chassis Line - Installed gear shift, radiator clips, hoses, washers and bolts into chassis using hand and air tools as well as torque gauges.
•Engine Line - Inserted grease and bolts into transmission, connected transfer case to transmission using a load assist tool, tightened down bolts and inserted clips and brackets to transmission.
September 2000 - June 2002
ZF Industries
Tuscaloosa, AL
Production Worker
Build Front and Rear Axle Systems for the Mercedes Benz M Class using both hand and air tools, load assist equipment, computerized label makers, testers and gauging equipment.
November 1987 - June 2000
Peavey Electronics
Meridian, MS
Production Worker
•Recycle Tech - Repair electronic and cosmetic failures, rejected by sub and/or final assembly. Keep daily reports on all failures and repairs.
•Line Support - Make sure all QA computer operators were properly trained and all computers, in my area, were functioning properly. Also enter QA data from production lines that did not currently have automatic data collection units.
•Final Quality Assurance Inspector - Perform a final computerized o manual (depending on the unit), performance test and a cosmetic check on the unit before shipping.
•Inspector Tester - Perform a computerized frequency response test and a cosmetic check on Signal and Effect Amplifiers and Patch Boxes.
•Assembly Line Worker - Build Signal and Effect amplifiers, Power Amps, Mixers, and Patch Boxes.
February 1986 - November 1987
Family Dollar Store
Butler, AL
Cashier
Run the cash register, put out floor stock, do layaways and returns and clean store.
August 1985 - February 1986
Pasquales of Butler
Butler, AL
Kitchen Worker
Prepare and cook food orders, run cash register, wash dishes and clean store.
June 1983 - August 1985
National Industries
Montgomery, AL
Assembly Line Worker
Build Harness' for Ford and Chrysler
Education
Meridian Community College
Meridian, MS
Electronics I, II(Digital Electronics), Microsoft Office 97, Peavey Advanced Prompts, Introduction of Peavey Prompts and Lotus 123, Micro Computers, JESP(Jobs Education Skills Program - Electronics I and II), MRP(Material Requirements Planning), Introduction to Computers(Apple), Elements of Quality Control, Basic Electronics and DC Circuits and Microsoft Excel
Massey Draughons Business College
Montgomery, AL
Records Management, Dictaphone Usage, Word Processing, Business Communications, Typing I, II, III, Business Law, Accounting I and Personal Awareness
Alabama State University
Montgomery, AL
General Studies
Skills Sheet
•Peavey Electronics - Ran a computerized QA Booth for 10 years and entered data under Word and Excel Programs as well as received and entered email on the intranet.
•Ross Collins Vocational School - Used electronic Work Bench and Computerized study and test programs.
Certificates
•Nov. 2003 - AIDT Honda Training Program
•Aug.2002-Sept.2002 - Forklift training, Mercedes Benz
•Sept.2000-June 2002 - ZF Industries and Mercedes Benz ISO-9000 Certification
•June 2000 - Blackfox Training Institute,LLC - ESD(Elector Static Discharge, Safety, PWB(Power Board) Assembly, THT(Through Hole) Component ID, and Slide Line Concept
•March 2000 - IPC Overview, Blackfox Training Institute LLC
•Nov 1997 - Electronics II Meridian Community College
•April 1997 - Electronics I Meridian Community College
•Oct. 1996 - JESP(Jobs Education Skills Program), Meridian Community College
•Dec. 1983 - Clerical, Massey Draughans Business College
Contact this candidate