Project Manager Service

Maurice P. Waynes * PELCHAT DRIVE HAMPTON, VA ****6 Phone: 757-***-**** ********@*****.***

Objective

To utilize skills obtained from two years of education in the service of HVAC and refrigeration equipment from college and ten years of HVAC installations.

Ability Summary

Read blue prints and schematic for HVAC and electrical fields and Power Supplies Continuity Testing OSHA Standards.

OSHA Standards Load Calculation Duct measurements & Installation Welding Schematic Blueprints Gas Pipe VAV Boxes Hanging Oven Hoods Test & Balance Trouble Shooting Multimeter's & Oscilloscope Basic Electricity AC/DC Motors Management Trainer Ventilation Exhaust Ice Machines Vacuum Pumps Pulling Vacuums Adding Refrigerant Soldering Brazing PLC Logic Heaters Timers Wiring Thermostats Zone Controls Calibration Microsoft Office Road Warrior Pneumatic

Employment History

HVAC Installer (Heating, Ventilation, and Air Cond 04/2013 - 10/2014 Atlantic Constructors Inc 6163 Jefferson Ave, Newport News, VA install and light service to all commercial hvac equipment

Heating and Air Conditioning Mechanic and Installe 09/2011 - 08/2012 Art Newsome Inc. newport news, VA Installation of all pipes,control wires, service and certified start-up of commercial hvac equipment

heating and air conditioning mechanic and installe 05/2011 - 08/2011 Rose Brothers yorktown, VA Installation and service of residential hvac equipment

HVAC Mechanic (Heating, Ventilation, and Air Condi 08/2010 - 10/2010 R.L. Midgett Chesapeake, VA Measured and cut insulation for covering surfaces, using tape measures, handsaws, knives, and scissors.

Fitted insulation around obstructions, and shape insulating materials and protective coverings as required. Determined the amounts and types of insulation needed, and methods of installation, based on factors such as location, surface shape, and equipment use. Installed sheet metal around insulated pipes with screws in order to protect the insulation from weather conditions or physical damage. Applied, removed, and repaired insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures. Read blue prints, installed light commercial and residential ductwork and HVAC equipment.

HVAC Installer (Heating, Ventilation, and Air Cond 01/2006 - 03/2008 Tradesmen International Greensboro, NC Selected appropriate insulation such as fiberglass, Styrofoam, or cork, based on the heat retaining or excluding characteristics of the material. Read blueprints and specifications to determine job requirements. Covered, sealed, or finished insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement or asphalt mastic. Prepared surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces. Removed or sealed off old asbestos insulation, following safety procedures. Measured and installed duct work, welded black iron, cut in and set unit curbs, and put units, vented and change outs.

Supply Room Clerk 02/2002 - 02/2005 Timco Greensboro, NC Received, stored, tested, and shipped products or materials. Train warehouse personnel. Scheduled and monitored air or surface pickup, delivery, or distribution of products or materials. Supplied aircraft mechanics with tools and parts for commercial aircrafts.

HVAC Mechanic (Heating, Ventilation, and Air Condi 03/1994 - 05/2002 Chisholm Services Burlington, NC Installed assembled, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, and down spouts, in supportive frameworks. Fabricated or altered parts at construction sites, using shears, hammers, punches, and drills.

Selected gauges and types of sheet metal or non-metallic material, according to product specifications. Maneuvered completed units into position for installation, and anchor the units. Transported prefabricated parts to construction sites for assembly and installation. Drilled and punched holes in metal, for screws, bolts, and rivets. Measured, wrapped and installed duct work, welded black iron duct, hung exhaust hoods, cut in and set unit curbs, ran drain lines, installed vav boxes, hung heats, measured and piped gas lines.

Education and Training

Completion Date Issuing Institution Location Qualification Course of Study Alamance Community College electronic technicians Hvac NC 2 Years of College or a Technical or Vocational School Electronics School MD 2 Years of College or a Technical or Vocational School

Occupational Licenses & Certificates

Certification Title Issuing Organization Completion Date Expiration Date CPR,AED, and basic first aid american safety & health institute OSHA 30 OSHA 11/2013 Tracpipe Certification omega flexible pipe 01/2010 CFC esco institute EPA Approved 11/2009 11/2013 11/2015

Contact this candidate