Electrical Engineer Design

Chetan Kumar Chenappa

**** * ******* ** *** **

Long Beach CA 90815

Phone: 562-***-****

Email: ******.******@*****.***

OBJECTIVE:

Seeking a Promising position where I can utilize my Engineering

skills while continuing to grow into greater capacity.

SUMMARY:

. MS in Electrical Engineer Major in Electronics & Communication.

. 1 Year Experience as a Hardware Engineer focusing on Wireless,

Broadband and CAN Networks.

. Have Project based Experience on Analog, Digital, Mixed-Signal IC

Design and Cisco Routing.

. Computer Programming Knowledge using C, C++ and SQL.

. Expert in writing Technical Specific Reports, Research Papers and Lab

test procedures.

. Demonstrated dependability, industrious judgment, decision-making

capability, budget management skills while responding to job

challenges.

TECHNICAL SKILLS:

Cadence, PSpice, Xilinx, Matlab, Simulink, LabView, AutoCad, Opnet IT

Guru, CCNA Network Visualizer, C, C++, MS-SQL, Linux, 8085, 8086 and 8051

Microcontroller.

TECHNICAL EXPERIENCE:

Data Grid Technologies, Bangalore, India

Hardware Engineer (July 2006 - July 2007)

. Provided Design and Development services for Analog and Digital

hardware, home networking and network appliances, integrating Internet

with communication devices.

. Designed subsystems for safety & stability and providing solutions for

information-access and other services.

. Analyzed & Debugged of 5ESS Telecom Network Switches sold by Alcatel-

Lucent.

. Analyzed circuit of these switches in the simulated live network and

checking the data flow.

. Isolated the problems in the software or hardware level.

. Replaced the hardware and wrote a patch for the software based on the

analysis.

Data Grid Technologies, Bangalore, India

Intern (September 2005 - June 2006)

. Developed a hard model for controlling the speed of a radiant

according to the engine temperature using Control Area Network (CAN)

protocol implementation.

. Worked on Embedded C programming and embedded integrated development

environment.

OTHER EXPERIENCE:

CSULB Sports & Athletic Center, Long Beach, CA

Student Assistant (Non-Technical, November 2007 - May 2010)

. Worked on Setting up, Ushering, Ticket Taking and Breaking down of the

Sporting & Cultural Events of the School.

EDUCATION:

Master of Science, Electrical Engineering (Spring 2010) GPA: 3.5/4.0

California State University Long Beach, CA

Bachelor of Engineering, Electronics & Communication (June 2006)

Visvesvaraya Technological University, India

PROJECTS COMPLETED:

Title : Control Area Network (CAN) Protocol Implementation.

Tool : Kiel Demo version with simulator.

Programming used : Embedded C.

Description : This Project involves developing a hard model for

controlling the speed of a radiant according to the Engine Temperature

based on CAN (Control Area Network) protocol implementation. CAN protocol

is used in various automobiles.

Title : Design of a CMOS Unity Gain OPAMP, Hysteresis

Comparator.

Tool : PSpice.

Description : Designing an OPAMP and Comparator with specific parameters

such as open Gain, temperature, VDD, Bandwidth, Input Common mode

Voltage, Input voltage swing, maximum input offset voltage, Input

Hysteresis, Input Reference Voltage, Output Load and obtaining the

desired graph.

Title : Design of a 4 bit by 4 bit Multiplier, Boundary Scan Test

(BST).

Programming used : VHDL.

Tool : XILINX ISE 9.2i.

Description : This design includes an 8 bit Adder, a Register

Accumulator, a Full Adder, 8 bit ripples carry Adder, an 8 bit register,

etc. To Test the PCB's using BST which is a method for testing boards

using a four-wire interface. The PCB used was Spartan 3.

Title : Building an OPAMP, Charge Redistribution DAC, CMOS

Inverter Layout, Extraction and Simulation, Building a Flash A/D

Converter using Cadence.

Tool : CADENCE.

Title : Setting up a Virtual Private Network (VPN) and its

Security

Tool : Opnet IT Guru.

Description : Creation of a VPN that can help communication to

remote places confined to a particular area which is simulated using Opnet.

Hence the user will be able to use the simulation to transfer files, voice,

and images as well as videos from one place to another and implementing

firewalls and security in a VPN.

Title : Adaptive Interference Cancellation.

Programming used : MATLAB.

Description : Adaptive Noise Cancellation is used to remove

background noise from useful signals. Algorithms used are least mean

square (LMS), Normalized least mean square (NLMS), Recursive Least

Squares (RLS) and Affine Projection (AP).

SEMINARS, TECHNICAL PAPERS & EXTRACURRICULAR:

. Presented a Technical Seminar on BRAIN COMPUTER INTERFACE (BCI)

technology.

. Wrote Research Papers on Quadrature Amplitude Modulation (QAM),

CMOS Current Reference (IRef), Flash ADC, ARM 7 in Cameras,

Wireless Application Protocol (WAP).

. Active Member of IEEE Society of Engineers.

. CCNA Certification Candidate.

. Represented University in Cricket, Soccer and Athletics.

. First Team Player for Southern California Cricket Association (SCCA)

Team.

Contact this candidate