Engineer Engineering

Julius Gunn

***********@*****.***

Current Address: ****-* ******* ***** ************, IN 46224 423-***-****

Permanent Address: 515 Biltmore Drive Chattanooga, TN 37411 423-***-****

Objective Reference my personal skills and achievements for employers for

the purpose of gaining employment.

Education Bachelor of Science Degree in Mechanical Engineering, The

University of Tennessee @ Knoxville Dec 2007

GPA: 3.27

Electrical Technician Certification Kaplan College

Dec 2009 GPA: 3.25

Technical Aerospace Engines (Duel spool, single spool, helicopter)

Operability Testing, Facility System

Skills Operability, (Piping and Valve, Mechanical and Electrical

Relay Systems), Blueprint Reading,

Technical Writing, Matrix Lab, PLC Logic, and MS Office Works

Engineering Rolls Royce Corporation Indianapolis,

IN

Experience Experimental Test and Assembly (Full Time) Jan

2008 - Present

. Responsible for integration and preparation of engine test

article (duel spool, single spool, helicopter engines) into

test stand for application of required test program.

. Responsible for preparing test set up instructions for the

purpose of integrating test article into the appropriate test

cell.

. Responsible for data attrition and trending for the purpose

of maintaining data integrity and engine performance and

health.

. Responsible for assembly of proper measurement

instrumentation for engine and facility health monitoring.

. Responsible for preparing engineering test reports accounting

test programming events including but not limited to (man

hour reports, engine fuel usage, electrical usage).

. Responsible for evaluating engine performance thru the use of

aerospace engine performance modeling equations and standard

day corrections to allow for performance correlation across

different environmental ambient conditions (pressure

altitude, ambient temperature, barometric pressure).

. Currently have published 7 technical engineering test reports

documenting the accounts of testing.

. Responsible for interfacing with Project Management

Engineering and Performance Engineering for simulating engine

test maneuvers.

Engineering Rolls Royce Corporation Indianapolis,

IN

Experience Helicopters Process Excellence (Co-Op) May

2007 - August 2007

. Led the Metal In Oil investigation for the Model 250 Series 2

& 4 Helicopter Engines.

. Primary objective was to find the leading root cause of

probable root cause for any metal generation within the

engine oil lubricating system.

. Statistical tools were used to evaluate collected data from

2002 to 2007. Data was then analyzed with Pareto Charts and

compared to 2007 Meal generation failure events.

Experimental Test & Assembly (Co-Op) May

2006 - August 2006

. Performed N1 Quad Coiled vs. N1 Dual Coil Speed Sensor Tests

for the purpose of evaluating engine speed based off of new

tachometer designed.

. Instrumental in discovering if the newly 2 prong insert N1

Quad Coiled Speed Sensor met design specs. as well as

performed better/worst than the single prong N1 Dual Coiled

Sensor.

. Performed the Pressure/Temperature Engine Health Test, which

was instrumental in discovering if Inner Turbine

Temperatures, Fwd Center Sump Cavity Pressures, as well as

Fan Speeds and Turbine Speeds were in line with the design

specs. for the AE3007 engine.

T&S Gear Technology (Co-Op) May 2005 -

August 2005

. Participated in the Artifact Gauging Study that classified

the CMM machines as being in good operational standing during

each work day.

. Started the basic framework for the Intelligent Gear

Database. The database serves as a collection of all gear

stresses and loads found in Rolls-Royce Engines.

Service Engineering (Co-Op) January 2005

- May 2005

. Lead 4th and 5th stage compressor blade failure

investigations seen on BA Citi Express Engines.

. Created a zoning illustration for High Pressure Turbine 1 & 2

Wheel that addressed new limits for inspectors to check

against.

Material Applications Engineering (Co-Op)

May 2004 - August 2004

. Identified and analyzed problems dealing with material

properties that where of concern to the M-250 Helicopter

series engine. Specifically at the Impeller and Spline Shaft

interface.

. Created a Design of Experiment (D.O.E) to help analyze which

materials/material coatings/surface roughness/lubrications

were best in the M-250 series engine at the Impeller and

Spline Shaft Interface

. Created test pieces in which I oil quenched, heat tempered,

tack welded to test the D.O.E.

Junior Manufacturing Engineer (Co-Op) August

2003- January 2004

. Edited blueprints and created shop floor routings for the

Manufacturing Engineering Turbine Group to aid in the update

of the operational shop floor routings and archives

. Aided in the development of a turbine blade rack for the

Turbine group, which served as a transport handling system

that was needed to decrease handling damage as well as damage

cause from blade transport between each machining operation.

The blade rack was set to be in production by January 30,

2004.

Sales Walgreens Chattanooga,

TN

Experience Sales Clerk June 2002 -

August 2002

. Accounted for cash, check, credit and debit card of customer

purchases and answered various inquiries and provided refunds

when necessary.

. Restocked supplies and assisted with inventory.

. Accounted for daily transactions of customer purchases

balancing at the end of shift with no or minor discrepancies.

Other Renaissance Presbyterian Church

Chattanooga, TN

Experience Church's Head of the Janitorial Staff

December 1999- April 2002

. Managed and supervised 3 crewmembers ensuring that the church

was clean for mid-week bible study and Sunday services.

. Conducted general routine maintenance to include: polishing

pews and furniture, mopping and polishing floors, cleaning

commodes, vacuuming the sanctuary, changing air filters

monthly, washing all windows, and disposing of the garbage.

Leadership

Experience

. UT Chapter of Pi Tau Sigma Engineering Honor Society V. P.

August 2005 - May 2006

. UT Black Cultural Programming Committee Team Leader August

2005 - Present

Honors

& Activities

. February 17, 2007 Honored as Black Engineer Student Leader of

the Year by Career Communications Group

. August 2006 Nominated by Rolls-Royce as the Black Engineer of

the Year

. August 2006 UT's Office of Professional Practice honored me

as a Co-Op Ambassador to the university's engineering program

. May 2005 named Mr. BCPC (Black Cultural Programming

Committee)

. November 2004 inducted into Pi Tau Sigma Engineering Honor

Society

. May 2004 - Present: Developing Home Recording Studio for

musical production

. June 2001 American Legions Boy's State Participant

Community Austin East High School

Knoxville, TN

Service Tutor October 2002

- May 2005

. Volunteer as a tutor at Austin East High School for the inner

city youth with The National Society of Black Engineers

sponsors the program that gives tutoring at Austin East High

School.

Contact this candidate