Engineer Maintenance

Tony Navedo IV

**** ***** ***** **

Fort Worth TX, 76123

Cell Phone: 910-***-****

E-mail: **********@*****.***

Active Secret Security Clearance

OBJECTIVE Obtain a career position with a company to utilize my Management, Electrical Mechanical Maintenance and Logistic skills.

SKILLS

Experienced in troubleshooting and operation of multiple pneumatic machine equipment, servo and stepper motors, inverters, spindle motors, proximity sensor controlled mechanics, modbus controlled devices, Plasma, Water jet, Router and pneumatic knife cutting as well as CAD/CAM programming, Hypertherm plasma units, KMT water intensifier and Ebbco filtration unit.

Skilled in fault isolation techniques to expose faulty equipment such as solenoids, relays, contactors, wiring per schematic and operator/programming errors.

Experienced with Radio Frequency test equipment such as spectrum analyzer, signal generator, digital phosphor oscilloscope, attenuators, diplexers, couplers, PC controlled automated test equipment, Data acquisition/switch unit, power supplies, laser range finder, forward looking infrared receiver, guided missile system coolant recharging unit, automatic video tracker, electronic control box assembly, and remote control units.

Skilled in CAD/CAM software i.e EnRoute and Alphacam, G-Code, and ucito language, Microsoft Windows, Word, Excel, Office, and PowerPoint

Awards: Army Commendation Medal for outstanding performance during Operation Iraqi Freedom.

COURSES/TRAINING

Avenger Missile System Repair: Completed 705 hours graduating with honors, attended basic electronics training, lectures and practical exercises covered AC/DC and resonance circuits, transistors, soldering, logic, and microprocessors

Armament Repair: completed 80 hours of small arms armament repair and performed direct and organizational support

High School Diploma

Electrical Systems Maintenance; 10 years

Soldering; 10 years

Armament Repair; 3 years

Vocational Welding; 2 years

Supply/logistics; 8 years

EXPERIENCE

2010-Present Multicam inc.

Sr Field Service Technical Support Representative

Regular duties: OEM equipment technician for multiple CNC platforms i.e. Routers, Water Jets Plasma, Oxy and knife cutting machines. Performed installations and training on machine operation, and programming in addition to specific applications cutting techniques. Conducted 50% of support via phone. Solutions typically required 50% mechanical, 25% electrical and 25% software.

2006-2009 JB Management/Syracuse Research Corporation (Warlock Program)

Site Lead Sr Field Service Engineer (Computer Engineer/Analyst L3)

Conducted Electronic Warfare System maintenance, supported initial field testing of a new Counter Radio Controlled Improvised Explosive Device System (RCIED). Training was given by one of the designing engineers at the production facility in Syracuse NY. Lessons covered system installation on multiple military and civilian vehicles, operation diagnostics/troubleshooting and repair procedures. On site in a dynamic multi-contractor/government environment and participated as part of an integrated product team for test and analysis. System test equipment included, spectrum analyzer, signal generator, digital phosphor oscilloscope, Data acquisition/switch unit, AC/DC power supply, DC/DC power supply, attenuators, diplexers, couplers, PC controlled automated test equipment and Anritsu hand-held spectrum analyzer.

Served as the Production Engineer as needed and full time Lead Technician during an upgrade assembly line to optimize system capabilities. Managing twelve other Field Service Representatives upgrading over 8,000 systems in country (Iraq) each system taking an average of four hours to complete the assembly line process.

Upgrade purpose was to open radio frequency range, output power and Xilinx access to the DDS and DSP. Consisting of installing one additional amplifier, multiple RF hard lines, upgraded firmware on Digital Signal Processor and Direct Digital Synthesizer, soldered 26 gauge wires to DSUB connector, replaced cannon plug and circuit breaker. Crimp 26 gauge contacts and inserted into Molex connector. Checked continuity between solder joints, Molex connector and DSUB connector. Post of final assembly system is run through Automated Test Equipment (ATE) to optimize system capabilities.

Instructor for formal and informal, classified and unclassified training lesions in a combat environment to Soldiers, Airman, Sailors and Marines. Course objective range from basic operators training to senior level instructor training.

Daily operations: Train other Field Service Representatives on proper installation, test each system for operability, troubleshoot faulty systems down to the component or circuit card and remove/replace techniques concerning Digital Signal Processors, Direct Digital Synthesizer, Dual Agile LO Synthesizers for High Speed Tuning/timing, Power Amplifiers, Power Filters, DC/DC power Supplies, RF lines, Wiring Harnesses, Antennas/Cables and Connections, Power boards and cables.

Ensured proper tolerances in Radio Frequency paths/power outputs (dbm) in Low and High Bands, Transmit/Receive functions, GPS satellite sink, Current draw, Temperatures and Analog to digital/digital to analog converters.

2005-2006 Washing Equipment of Texas

Field Service Technician

Perform troubleshooting, maintenance, service calls and assist with complete install on Laser-wash 4000, G/5 and G/5s. Maintain and repair plumbing with pressure up to 1,200psi. Troubleshoot high pressure and low pressure pumps, contactors, overloads, pressure switches, single and three phase motors, solenoids, danfoss valves, check valves, pressure regulators, gearboxes, amplifiers, relays, magnetic switches, photo eyes, ultrasonic sensors, all kinds of circuit cards, software upgrades, complete wiring of systems, reverse osmosis systems, water softeners, cable pulling and wire landing. Maintenance and service includes 50% Electrical 50% Mechanical. Troubleshooting includes Fault isolation and repair/replace techniques. Work also requires documentation, coordination, organization and PC skills

2001-2005 United States Army

E-4; Honorable Discharge

Avenger Missile System Repairer:

Performed quality control measures, conducted maintenance adjustments on test equipment, served on maintenance and inspection teams

Inspected, tested and adjusted components to specific tolerances, determined shortcomings and malfunctions in electronic, electrical and cryogenic assemblies, modules and circuit elements using system associated equipment

Removed and replaced defective line replaceable units, including interconnection cables, determined serviceability and disposition of assemblies, subassemblies and parts, removed and installed servomotor/Azimuth Gear Assembly

Performed inspections of system maintenance, ensure quality control measures are implemented, supervised lower rank soldiers and provided technical guidance

Armament Repair:

Repaired and maintained various advanced military weapons systems valued at up to $1,000,000 cleaned and lubricated electro-optical fire control components to ensure proper maintenance

Repaired and maintained sophisticated weaponry such as missile mounts, platforms, and launch mechanisms, tested and adjusted weapons firing, guidance, and launch systems

Supply/Logistics:

Supervised and coordinated activities of workers concerned with ordering, receiving, storing, inventorying, issuing, and shipping materials, supplies, tools, equipment, and parts in stockroom.

Planed layout of stockroom, warehouse, and other storage areas, considering turnover, size, weight, and related factors, scheduled work for special and periodic inventories, reviewed records for accuracy of information and compliance with established procedures, and to determine adequacy of stock level

Electro-Optical Repair Technician

LSI

Perform Electro-Optical maintenance and repair to ground ordinance laser and night vision devices, small missile systems, and other fire control equipment.

Perform mechanical, optical, electrical repairs to include inspecting, trouble shooting, and adjusting fire control instruments and systems. Complete basic shop administrative documentation and records using technical publications and standards.

Contact this candidate