Engineer Project

TEODULO AYCO MAGDOZA

IC No. S*******C

FACILITIES / M& E / INSTRUMENT &TELECOM ENGINEER

Blk 568 Pasir Ris St. 51 #02-88 Lot 55/56 Phase II Camella Homes Subdivision

Singapore 510568 Lawaan, Talisay City, Cebu Philippines. 6045.

HP : +65 92230295

Home/Fax : +65 83686924

Email : ********@*****.***

C A R E E R O B J E C T I V E

To pursue a challenging career in the field of Facilities / M & E / Instrument / Telecoms Engineering Technology and to enhance my knowledge in the Manufacturing / Construction and Commissioning in Oil & Gas field.

QUALIFICATION S U M M A R Y

A total of 20 years of active work experiences in the field of Mechanical & Electrical and Instrument and Telecom Engineering Systems involving design, estimation, supervision implementation, installation, inspection and maintenance of facility management.

Also with extensive exposure in the areas of installation, mounting, inspection, operation and maintenance of Mechanical & Electrical/Instrument system covering Voltage up to 22 kv and below 100v to Power Substation, Distribution lines, Power Generators, Switch Gears, Motors and Controllers, Load Center, HMI, DCS/FMCS, Power and Lighting Point, Power Metering, Power Capacitors, Power Transformer, LAN/WAN, Telephone and Security Card Access System, CCTV System and Fire Alarm System, VSAT,(PA/GA),& TVRO.

Also with strong experience in the Air Conditioning and Mechanical Ventilation System (AHU, RCU, FCU, Chiller and Cooling Tower) Fire Protection System, Sanitary-piping Elevator, Escalator and, Boiler.

E D U C A T I O N A L B A C K G R O U N D

1985-1989 University of Bohol (Philippines)

B. Inting St. Tagbillaran City Bohol PHILIPPINES

Bachelor of Science Degree in Electrical Engineering

License Electrical Engineer of the Philippines

1984-1985 Peoples Electronics Servicing

Central Park Subdivision Camarines Sur PHILIPPINES

Electronics Vocational Course (Basic Electronics)

1980-1984 Saint Vincent Institute

Maribojoc Central, Maribojoc Bohol PHILIPPINES

High School Education

1972-1978 Cabawan Elementary School

Cabawan Maribojoc Bohol PHILIPPINES Elementary Education

S E M I N A R S / W O R K S H O P S

March 26, 2009 - Safety Orientation Course Oil/Petrochemical (NTUC Singapore)

Dec 03, 2008 - Travel Safety By Boat OPITO (MSTS Asia Singapore)

Oct 12, 2007 - Shipyard Supervisors Safety Course (NTUC Singapore)

May 06, 2006 - Shipyard Safety Instruction Course (NTUC Singapore)

Oct 07, 2004 - Module 3 Communicating for the Knowledge Economy: Speaking &

Listening (British Council)

July 12-13, 2000 - Productivity Management Course (NTUC Singapore)

April 22, 1995 - Energy and Demand Side Management (IIEE Phils.)

Oct 22, 1994 - Medium Voltage Switchgears/Substation for Commercial &

Industrial Plants Seminar

July 02, 1994 - Fundamentals of Illumination Design for Commercial & Industrial

Buildings (IIEE Phils.)

March 27, 1993 - Technical Seminar on Ind. Motor Controllers Basic &

Hi-Tech (IIEE Phils.)

Dec 17, 1988 - Short Circuit Calculation (IIEE Phils.)

T R A I N I N G S

01/12/08 to 03/12/08 - Basic Offshore Safety Induction & Emergency Training

with HUET EBS OPITO (MSTS Asia Singapore)

28/04/05 to 29/04/05 - Customized Fire Fighting & Breathing Apparatus Course

(Singapore Aviation Academy)

10/02/04 to 16/02/04 - Metal Scaffold Erection (Building & Construction Authority, Singapore)

05/0796 to 27/09/96 - Air-conditioning Technician Training Program

(Utopia-Aire Singapore)

04/05/89 to 05/06/89 – Advance Summer Camp Training (MS-43) CL 89

(Camp Lapu Lapu Cebu City Philippines)

SPECIAL TRAINING / SKILLS

* Hands-On on Personal Computer, Laptop Installation, Repair Both Hardware & Software

* Basic Knowledge in AUTOCAD

* Proficiency in English.

P E R S O N A L B A C K G R O U N D

Date of Birth : February 17, 1965

Place of Birth : Antequera Bohol Philipines

Sex : Male

Civil Status : Married

Nationality : Filipino (Singapore Permanent Residence)

IC No. : S2712414C

Race : Filipino

Passport No. : XX4322995

Height : 5’ 4”

Weight : 75 Kgs.

Religion : Roman Catholic

Hobby : Playing Basketball, Bowling, Badminton, Volleyball

P R O F E S S I O N A L E X P E R I E N C E

May 2012 – Jun 2012 E&I Com EX Inspector (SBM ANCHIETA FPSO PROJECT)

(E&I Inspector & Mechanical Completion )

Keppel Shipyard Ltd Tuas, Singapore

Ogre Pte Ltd.

31 Jurong Port Road, 02-12 Jurong Logistics Hub

Singapore 619115

Jan 2012 – Mar 2012 E&I Commissioning Supervisor (BWO FPU PROJECT)

(Electrical&Instrument MC/Commissioning )

Sembawang Shipyard Ltd, Sembawang Singapore

BW Offshore Singapore Pte Ltd.

10 Pasir Panjang Road, Mapletree Business City #17-01

Singapore 757516

Feb 2011 – Dec 2011 Electrical Supervisor (MODEC PSVM FPSO PROJECT)

(Electrical&Instrument MC/Commissioning )

Jurong Shipyard Ltd Tanjong Kling, Singapore

Asiapac Commissioning Services Pte Ltd.

190 Woodlands Industrial Park E5 #10-12/13 BizHub

Singapore 757516

Sep 2010 –Jan 2011 E&I Engineer (SEA DRAGON II SEMI-SUB PROJECT)

(Electrical&Instrument’s InstallationMechanical Completion )

Jurong Shipyard Ltd Tanjong Kling, Singapore

Meggawatts Engineering Services Pte Ltd.

10 Kian Teck Way, Singapore 628747

Jan 2010 – Sep 2010 E&I/TELECOM TECH (SBM OKHA FPSO PROJECT)

( Instrument’s Inspector & Mechanical Completion )

Keppel Shipyard Ltd Tuas, Singapore

Wartsila Singapore Pte Ltd.

11 Pandan Crescent Singapore 128467

Feb 2009 – Jan 2010 M &E Project Lead (Chevron Oronite PROJECT)

Chevron Oronite Pte Ltd, Jurong Island Singapore

PanGreatWays Engineering Pte. Ltd.

20 Benoi Road Singapore 759947

Sep 2008 – Feb 2009 E&I Senior Comm Supvr (PetroBras Prosafe PROJECT)

( Instrument’s Inspector & Mechanical Completion )

Keppel Shipyard Ltd Tuas, Singapore

PanGreatWays Engineering Pte. Ltd.

20 Benoi Road Singapore 759947

Sep 2007 – Aug 2008 E&I &TelecomLead.(BOHAI ConocoPhillips PROJECT)

Sembawang Shipyard Pte Ltd, Sembawang Singapore

PanGreatWays Engineering Pte. Ltd.

20 Benoi Road Singapore 759947

Mar 2006 – Sep 2007 E&I PROJECT ENGINEER (SAMSUNG SILTRONIC)

12 Tampines Industrial Ave 5 Singapore 528759

Kurihara Kogyo Co., Ltd.

168 Jln Bk Merah Connection One Tower 3 Singapore 150168

Aug 2001 –Feb 2006 Senior Associate Engineer (Simicon Manufacturing)

Pasir Ris Industrial Area, Singapore

System on Silicon Manufacturing Co. (SMC) Pte Ltd

70 Pasir Ris Industrial Drive 1Singapore 519527

Apr 1996 –Jul 2001 Electronics & Air-con Engineer (Servicing Company)

UTOPIA-AIRE Pte Ltd

7 Kaki Bukit Place Eunos TechPark Singapore 416185

Jan 1994 – Apr 1996 Eng’g Dept Head(COMMERCIAL BLDG PROJECT)

Metro (GAISANO) Ayala Centre

Cebu Business Park, Lahug Cebu City Philippines 6000

Jan 1991- Nov 1993 Electrical Supervisor (YLLANA DREDGE PROJECT)

Keppel Shipyard Corp., Cebu Philippines

Socor Shipping/Const’n Corp.

Pier 4, Reclamation Area, Cebu City, Phils

J O B S U M M A R Y

JOB DESCRIPTION AS AN INSTRUMENT SENIOR COMMISSIONING SUPVR.

• Carry out loop testing, calibration, simulation, troubleshooting, of all process instruments used to measure, monitor, records and controls different process variables such as flow, pressure, level, temperature and others. Pressure/Level/Flow Transmitters (Rose Mount, Yokogawa, ABB, Siemens, Endress + Huuser,), Solenoid Valve / Control Valve (Masoneilan, Fisher controls, Forbes,Marshal, ASCO, Rotex, FESTO)

• Testing, simulation of motor interfacing at HMI and DCS such as motor status signal, start/ stop command, manual/auto status, and PSD interlock. Simulation and cause and effect testing of all emergency and shutdown devices.

• Familiar in working with instruments use in Distributed Control system with the following brand; : Fisher Instruments, Rosemount Instrument, Massonneilan, Foxboro, Moore. With good knowledge in all electro-pneumatic and hydraulic instruments.

• Have a good understanding of Piping and Instrument Diagram and Instrument Loop Diagram.

• Responsible for the EFMCS P&ID, I/O List, Shop Drawings, Instrumentation Location Layout, Isometric Drawings Details for FMCS, Fiber Optic Routing, FMCS Block Diagram, Air Differential Pressure Piping Layout, VSD MCC Allocation for Frofibus & Simocode Looping Connections.

• Prepare & sign for all the ITRs for the completed hot loop check/functional check from CCR to Field Instrument, and submit to the PIMS to clear PC ITR.

JOB DESCRIPTION AS CONSTRUCTION E&I ENGINEER

• To carryout revision of drawing, job technical evaluation, Planning, supervision and co-ordination for, Loop check, Pre-commission and commissioning. Preparation of instrument inspection test record (ITR’S) as per specification.

• Study and review vendors drawing/ documents and ensure implementation in compliance with specifications.

• Conduct Electrcal and Instrument inspection in the installation, modification and fabrication done by contractors.

• Prepare site inquiries for Electrical/Instrument fabrication installation and issues within the contractors.

• Assist client to modify system connections due to changes of design. Responsible for scheduling and distribution of job orders.

• Monitor Electrical and Instrument contractors for modification of cable tray supports, cable trays interfacing all modules to cable racks and underneath modules.

• Monitor Electrical, Instrument and Telecommunication, cable pulling cable glanding and termination to the local and main control panels.

• Compiling all as-built drawings and update latest revision as per Engineering design for proper documentations and references.

• Prepares project work schedules progress monitoring and daily/ weekly progress report.

• Prepare material lists and manpower requirements.

• Liases with client representatives for proper channeling.

• Attend daily meetings with client, subcontractors for work progress and technical aspect.

JOB DESCRIPTION AS AN INSTRUMENT INSPECTOR, MECHANICAL COMPLETION, QA/QC

• Detail visual inspection of all hazardous area, ex certification instrumentation and to ensure installation and equipment meet relevant standards

IEC 60079-10.Visual inspection for complete and corrective installation of unit

control panel. System wiring matching, System cabinet wiring trouble shoot.

Pressure testing for pneumatic impulse line, cable IR test prepare and summit MC

check list, ITR checklist.

• To carryout revision of drawing, job technical evaluation, Planning, supervision and co-ordination for, Loop check, Pre-commission and commissioning. Preparation of instrument inspection test record (ITR’S) as per specification.

• In addition, cable schedule. Inspect electrical apparatus and Instruments for hazardous area requirements like zone, category, class/division and EPL category. Comp ’Ex’.

• Been an owner representative withhold the position of QA / QC supervisor responsible and ensure for final acceptance on the matter of inspection Coordinate the work with in-house contractor material purchase, manpower control and costing responsible allManpower control, curing of punchlist, daily job progress and coordinating with engineering department for design modification methods of protection (ATEX), and intrinsically safe hazardous area equipments installations. review document’s prior to ELECTRICAL and INSTRUMENT completion acceptance before START-UP. Reporting to the senior construction manager.

JOB DESCRIPTION AS TELECOM ENGINEER / LEAD

• In-charge of the TELECOM System Installation for the BOHAI FPSO Project from Conoco Phillips. Responsible for the installation, carry over works,

• Pre-commissioning and commissioning of the following FPSO Telecommunication Systems: Metereological Systems (windspeed and direction, cloudheight ceilometer, helideck motion sensor, stevenson screen pressure, air and humidity sensor, current sensor), UHF system field, UHF repeater Radio System, VHF Aeronautical Radio system, VHF Marine Radio System, Non-Directional Beacon System, Closed Circuit Television(CCTV) VSAT (stabilized antenna), B & D Local Area Network (LAN), Wide Area Network (WAN) Public Address and General Alarm (PA/GA), TVRO Entertainment System, Line Of Sight (LOS), PABX System, Inmarsat System, Collision Avoidance Radar System, Gyro Compass System

• Supervised the operation and maintenance of PABX Intercom system (Alcatel Brand). Perform weekly progress report & submit to the Manager Check, Approved & Signed all the completed ITRs prepared by TELECOM Supervisor.

• Responsible in monitoring and inspection for the compliance in the implementation in the execution of the scope of work carried out by contractors and vendors to ensure consistent application of owner approved standards and specifications.

• Coordinate and liaise with vendor and contractor’s representative in the field concerning work progress, outstanding issues and other related matters.

• Supervise installations of Telecommunications equipment (PA/GA, GMDSS, VSAT, GYRO, NDB, ESD, TELEPHONES, INTERCOMS, CCTV, Weather Station, UHF, VHF Marine, MF/HF Radios, UHF Repeaters, and Entertainment Systems).

• Attend Tri-party inspection with client and contractors.

• Responsible for punch list items and mechanical completion work scope.

• Review and fill-up Instrument Test Record (ITR) sheet as actual performance of each loop testing to ensure every parameter engaged to each system are acceptable to clients.

JOB DESCRIPTION AS M & E PROJECT LEAD:

• Responsible for the entire project cycle - initiation to closure and covering all functions as a Project Engineer. Liaise closely with the Project Team, the Project Management Plan and keep it up to date during the life of the project. Responsible for defining & managing the project budget, resources and keeping the project within time schedule, Identify the risks, issues, and manage the associated corrective action plans.

• Execute Mechanical & Electrical works and Supervise and monitor all site work Liaise with Clients, Project Manager, sub-contractors and suppliers Attend site technical, coordination and safety meeting HVAC; Mechanical & Electrical & Other Discipline. Good knowledge of safety regulations and procedures. Fire Protection, ACMV system project installation, shop dwg preparation, co-ordination, T & C. Able to liaise with Consultants, Authorities, Builders & Subcontractors, Able to guide and lead a team of in house work force.

• Manage the overall project planning, propose and implement corrective actions to ensure smooth delivery of project. Provide the project evaluation and project status to management on a regular basis. Good knowledge in extracting VO’s and preparing quotation.

JOB DESCRIPTION AS AN ELECTRICAL ENGINEER:

• Inspection, testing, site surveys and discrimination analysis services Replacement of equipment and control systems Main Switchboards, Emergency Switchboards, Generator Panels, Group Starter Panels Motor Control Centers/Group Starter Panels (Starters of fixed type or draw-out type) Distribution Boards, Individual Motor Starter Panels, Shore Connection Boxes, Navigation Light Panels, Transformer Panels, Battery Charging & Discharging Panels, Engine Control Room, Control Consoles, Bridge Control Consoles, Total Information and Control Systems, Data Transmission and Control System, Engine Monitor and Alarm Systems, Generator Automatic Control Systems, Reefer Container Monitor Systems, Cargo Control and Monitor Systems, Energy Saving Systems

• In-charge on all contractors for site implementation of all Electrical & FMCS job scoop of work. Supervised the operation and maintenance of power house with 3-1750KVA GENERATOR SET with automatic synchronizer. Sub-station with 2-3.5MVA Distribution Transformer (24KV Primary and 440V Secondary) controlled by 2-4000A ATS Supervised the operation and maintenance of 3-440Tons Centrifugal Type Chiller for air-conditioning system, (York Brand). Maintenance of 3-25KW Cooling Towers (BAC Brand). Supervised the operation and maintenance of 9 units Refrigeration (Hussman Brand).

• Perform rack-in & rack-out of LV & HV Circuit Breakers and Isolator Switch.

• Testing of LV & HV Power Cables using Megger Tester and performed High Pot Test, check operation of protection relays, testing either Primary or Secondary Injection.

JOB DESCRIPTION AS A FACILITIES SENIOR ASSOCIATE ENGINEER:

• Operate and maintain facilities systems such as Control, Electrical, Air-conditioning and Mechanical Ventilation Systems, Fire Protection & Detection, Ultra Pure Water, Clean-room System, Industrial Waste Treatment Plants and Chemical and Gas Systems for a Wafer Fabrication plant.

• Review of system status in FMCS and alarm analysis, Trouble-shooting Facilities alarm response & service normalization, Perform scheduled preventive maintenance (PM) and system calibration on a timely basis, Perform first line incident handling, alarm response & breakdown repair works as well as actively participate in ERT incident.

• Perform inspection rounds and manual data logging for facilities systems, Perform facilities system isolation or lock out for after office hours contractor works. Supervised/Performed Installation, Testing, Commissioning and Maintenance of Security Card Access System and Door Locking Devices. In addition, appointed

shift leader will perform shift handover, planning & allocation of daily tasks to shift members, generation of system performance(using SAP) & weekly utility consumption reports. Shift leader will also handle all communication, daily log, EAR write-up & sign off, co-ordinate Work Permits and CMMS management.

JOB DESCRIPTION AS AN AIR-CONDITIONING ELECTRONICS ENGINEER:

• Lead a team of Technical Officers in performing preventive maintenance and corrective maintenance of mechanical & electrical systems such as air-conditioning equipment (large water-cooled chillers, pumps, cooling towers) Air-con servicing for split unit/ VRV/ CHW FCU & CHW AHU for building and tunnel ventilation system (tunnel ventilation & tunnel booster fans).

• Perform instrumentation, set up and testing of refrigeration systems

• Perform service and maintenance of laboratory and test cell facilities.

• Assist in the building of prototypes and set up for component testing.

• Assist in calibration of test equipment

JOB DESCRIPTION AS AN ENGINEERING DEPARTMENT HEAD:

• Supervise and direct the performance of repair jobs scheduled by Building Maintenance Section Head.

• Evaluates and presents for interview request for new equipment and recommends purchase of replacement parts.

• Reports new system and simplify the work for inclusion in maintenance policy reformation.

• Implement through assignment of tasks safety and fire prevention policies and procedures.

• Review and check the completion of PMS with a regular report to the Building Maintenance Section Head.

• Exercise effective control over tools, materials and supplies through daily recording and monitoring.

• Provides technical assistance and training to subordinates in difficult repair job.

Plan work schedules, and assign subordinates to specific duties to coordinate

unit activities.

• Provide -on - the training and ensure subordinates compliance with established policies and procedures.

• Evaluate performance, schedule training, leave, and recommend action and movements of personnel.

• Review and ratify reports and communication prepared by subordinates, materials and supply request.

• Prepare and submit for review budgeted expenditures for headcount, services, training materials and supplies.

JOB DESCRIPTION AS AN ELECTRICAL SUPERVISOR:

• In-charge in all additional projects both Electrical, Mechanical and Electronics works. Supervised hands-on in troubleshooting motor control devices, panel boards of magnetic coupling with AC-DC power source, swing wench motor, cutter motor, spud motor, ladder wench motor, synchronizing panel of 2-600KVA GENERATOR SET.

• Supervised / Hands-on in rewinding governor motor, magnetic coil relay, motor generator, 250KVA Generator (Caterpillar Brand). Excites 250KVA Generator (Caterpillar Brand), 20KVA and 15KVA Generators (Denyo Brand) Troubleshoot and repair all electrical and electronics equipment’s / devices. Routine preventive maintenance, servicing of all electrical switchboards, switchgears, alarm & monitoring systems, fire detection and alarm systems; generator automatic control systems; ships’ automation & instrumentation.

• Fault finding, rectification and repair works. Upgrading, modification, extension and retrofitting works, Thermo-grapy works Supervised/Performed INSTALLATION AND maintenance of HIROSS HIPOWER-T UPS SYSTEM

Contact this candidate