JOHN H. SPANN, SR.

**** **** ***** ******

North Charleston, S.C. 29418

843-***-**** (cel) 843-***-****

OBJECTIVE: Seeking to utilize gained experience where I will excel in technical knowledge to the fullest extent career growth.

EDUCATION: NORFOLK STATE UNIVERSITY- NORFOLK V.A.

BACHELOR OF ART: Interdisciplinary Studies

Graduated 1995

DENMARK TECHNICAL COLLEGE- Denmark S.C.

ASSOCIATE DEGREE: Blueprint Sketching and Drafting

Diploma: Tooling and Machine Shop

Coursework: Electricity I & II and Machine tooling

Graduate 1982

EXPERIENCE:

10/08-PRESENT HINDS ELECTRIC COMPANY

P.O. BOX 5975

WEST COLUMBIA, SC 29171

ELECTRICIAN

Responsibilities: Work on high and low voltage, set light and receptacle, wire low voltage fire alarms, smoke detector, door bells, security camera, and lights, ran fiber optic and catw 5 and 6, wire set comdial panel and punch down 200 pairs 50 and 25 pair cable panel, terminated 110 penels and transformer, disconnect, and circuit breaker. Did all testing and troubling of wires, used amp meter, volt tester, amp probe multimeter and meg all high gear

ELDECO ELECTRICAL

8/05-04/08 5751 AUGUSTA RD.

GREENVILLE, SC 29605

ELECTRICIAN

Responsibilities: Supervised a crew of 15 workers. Worked on

high and low voltage, terminated all high and low voltage, phased

out all wire pairs, terminated all gears, transformers, all

disconnects, and circuit breakers. Set and installed switch gear, Megg and tested 600. 500,400,and 350 wire, used megger, amp probe, multimeter volts tester and ampmeter, ran conduit, riddgett and EMT, ran cable tray, also cad weld ground wire.

ROBERT BOSCH CORPORATION, MIA MAU

9/04-08/05 8101 DORCHESTER ROAD

CHARLESTON, S.C. 29418

ENGINEERING TECHNICAN

Responsibilities: Test injector, set up stand, change cam, fixture, rocker arm, exchange engine and stand, exchange block, inspect injectors stators, push rod, valve, armature, spring cage, plunger, follower, nozzle nut, stop plate, nozzle and valve stop, and body. Also installed input and output modules, motor drive sequencer, also installed panel view and programmable controls. Rewire all electrical components, to include fuel and oil line. View and inspect all injector parts under a microscope. Set up test pulsesation and endurance, calibrate all stand, run all computer programs for all stands, contact vendor for parts and quotation.

All work was done under careful observation.

04/02-08/04 Holy Hill Heating and Air- Holy Hill, S.C.

Responsibilities: service and Repair AC units, consisting of

Commercial Industrial and Residential. Troubleshooting repairs, electrical components relays, transformers, contactors, circuit boards, replaced compressor, dryers, coils, pump down system, reclaim Freon, charge Freon in cooling system, maintain, boilers and chillers, read all pressure gauge, change filters, also change cones in cooling towers. Did all soldering and brazing, did all change out, all duck work ran all pipe and wiring. Also vacuum down system, also HVAC Certified.

EXPERIENCE: MOBILE TOOL INTERNATIONAL – Westminster, CO

9/98 – 2/03 SERVICE REPRESENTATIVE

Responsibilities: service and repair and inspect aerial lift trucks, which included; trouble shooting all electrical, mechanical and hydraulic aspects of lift. Rebuilding hydraulic cylinder, testing hydraulic pressure. Change, replace and repair of all hydraulic components, which included; lines, hoses, fittings, filters, rings, seals, shafts and pumps. Did all electrical work, rewired entire machine. Replaced breaker, fuses, and relays, switches, control levers. Replaced and rebuild motors and onans. Did all mechanical repairs of lifts, which included replacing gears, sprockets, chains, shafts, cylinders, hoses, wear pads, shims, mounting bolts, booms, buckets, pins, greased all fittings, replaced bushing and sleaves. All work was scheduled on personal customer contact, kept all data and files on lap top, very familiar with computer.

7/93 – 8/98 VERBATIM OF CHESAPEKE – Chesapeake, VA

MAINTENANCCE ENGINEER

Responsibilities: did preventative maintenance on total plant, to include; trouble shooting, modification, repair and installation of high-speed production equipment. All machines were run on an assembly line that was controlled by Allen Brady and Omrons plc’s. Repaired Branson ultrasonic welder, replaced cam gear, tie rods, cam rollers and cams. Familiar with all pneumatics, rebuild vacuum pumps, electric motor (single phase and three phases), replaced optical sensor, relays, limit switches, also repaired all other electronic devices, upkeep of chillers and boilers in hvac systems. Did all work on continuous production line. Familiar with all robotic arms, suction cups and pads, replaced all air lines, vacuum lines, and hydraulic lines.

EXPERIENCE: System Integration - Portsmouth, VA

7/92 – 2/93 Control Technician

Responsibilities: installed and read all gages, modules input and

output, all flow input and output gages. Read all seamens, Johnson controls and uni tope controls. Did all upkeep and repairs on chillers and boilers in plants. Did all hvac repairs and service. Read and replaced all temperature controls, replaced valves, sensors, and kept daily log sheet.

6/91 – 4/92 FLOWERS BAKING COMPANY – Jacksonville, FL

ELECTRO-MECHANICAL MAINTENANCE TECHNICIAN

Responsibilities: troubleshooting, repair and replaced air conditioner refrigeration, compressors, boiler system, conveyor belts, shafts, pumps, hydraulic lines and hoses, rebuilt motor and pumps, also did all electrical maintenance of plant, which included; rewiring machine, repairing circuit breakers, rebuilding motors. Did all refrigeration and ac system, also upkeep of boilers and chillers. Also maintained cooling tower. All work was done on a high speed Production line, replacing belts, gears, chains, couplings, sprockets, rollers, bearings, and shafts. Modifying and fabricating as needed.

8/82 – 4/90 GEORGIA PACIFIC INC – Russellville, SC

ELECTRO-MECHANICAL MAINTENANCE TECHNICIAN AND MILLWRIGHT

Responsibilities: troubleshoot, repair and replace mechanical and electrical components. Replaced conveyor belts, shafts, pumps, hydraulic lines and hoses. Replaced and rebuilt electrical motors and pumps, chains, gears, sprockets, shafts, bearings, rollers, hydraulic valves, filters, switches, cylinders, seals, bushings, rings, and fittings. Did electrical up keep of plant, which included; rewiring circuit breakers, rewiring machines (welds and fabricated machine parts). Did all upkeep of chillers and boilers, also installed input and output modules to include seamens and Johnson controls. Read all gages, flow meters, and pressure gages. Also familiar with Allen Brady programmable controls, relays, optical sensors and limit switches. All work was on a very high speed continuous Production line.

Contact this candidate