Engineer Project

ANDY LIAO

Phone: 571-***-**** E-mail: hzi81v@r.postjobfree.com, Reston, VA 20190

Seeking Engineer Position

Clearance: DOD/Secret/active (US citizen)

Certifications: DAU- System Acquisition Management II

PROFESSIONAL EXPERIENCE

Consulting Engineer, Reston, Virginia 08/2010 – Present

Energy/Mechanical Engineer

•Developed project schedule, financial model, project cost life cycle, heat & mass balance and logistics plan for a 150MW combine cycle and 80 MW steam cycle power generation facility with gas/steam turbine, Heat Recovery Steam Generator (HRSG) and export process steam.

•Supported EPC review on proposal/specification/ cost control/ program schedule control/ P&ID drawing in Mechanical Engineering – Hydraulic system, Building Automation, power generation cycle, BOM, acquisition and logistics plan.

•Developed cost, BOM for on site renewable energy and biomass cogeneration facility.

CH2M Hill - U. S. Air Force Joint Base Ballad, Iraq 01/2010 - 08/2010

Project Manager

•Supported and deployed U. S. Air Force 332nd Expeditionary Civil Engineer Squadron at Balad, Iraq.

•Applied DOD Acquisition/ Logistics Policy- generated statement of work (SOW), Government Independent Cost Estimates; BOM, project schedule, developed preliminary mechanical design drawing and

acquisition form 9/1391 for mechanical engineering projects.

•Completed non-tactical vehicle fuel point (NTV), HVAC/ Building Automation, Power/Diesel Generator, Tactical Buildings and Fire Suppression projects.

•Completed hydraulic system design for air lifting system including power unit, valve assembly table,

Servo and Servo /proportional vale assembly.

•Completed project of Solar renewable energy lighting system at the base.

Consulting Engineer, Reston, Virginia 01/2009 – 01/2010

Mechanical Engineer

•Developed project schedule, business model to include project cost life cycle model, heat balance for Combine/Steam Cycle Power Generation and on site biomass cogeneration facility. Generated project schedule, BOM and preliminary design drawings.

General Dynamics, Woodbridge, Virginia 01/2008 - 01/2009

Mechanical/System Engineer

•Supported U. S. Marine Corps on Expeditionary Fighting Vehicle (EFV) project in the areas of System/Subsystem Design Detail (S/SDD); Preliminary Design Review (PDR)/Critical Design Review (CDR) peer reviews, project schedule and survivability analysis.

•Completed hydraulic logic design, power unit, drawing, BOM.

•Completed vehicle Fluid Interface and hydraulic line replace unit analysis in terms of operational parameters, interfaces requirements in subsystems for land, transition and sea modes.

•Completed System Functional Architectural Interface and Fluid Interfaces Diagram for the subsystems in the vehicle. Analyzed and provided inputs to improve the performance for the Mechanical Subsystems – nuclear-biological-chemical (NBC), Hydraulic, Environmental Control Unit/HVAC, Hydrodynamic, and mobile subsystems.

•Maintained subsystems specification, work breakdown structure, product tree diagram. Performed configuration management (CM) tasks for subsystem specifications.

•Completed parts list logistic plan and cost analysis for subsystem design changes.

Rockwell Collins, Sterling, Virginia 07/2006 - 01/2008

Manufacturing/System Engineer

•Supported U. S. Air Force communication project on B52 Flight Simulation and Antenna RF project.

•Completed interface requirement between hardware and avionics components; generated the antenna installation/design plan, facility layout diagram, and cable diagram; and completed the human factors, safety and wind load analysis.

•Provided project and technical direction to the design support engineers to the design model of the console and equipment rack and release structure, assembly, wiring drawing and parts lists for processing acquisition/Logistics plan.

•Supported Preliminary Design Review (PDR)/Critical Design Review (CDR) peer reviews; developed project schedule, capitalized and executed the engineering hour, budget, material cost plan, researched vendors for equipment, components, and spare parts

•Performed Configuration Management tasks for subsystem specifications and performed Earned Value Management as to the design change, cost estimation and program schedule.

BAE Systems, Silver Spring, Maryland 01/2004 – 07/2006 Mechanical/System Engineer

•Supported Navy Strategic Systems Program (SSP) on Submarines SSGN Strategic Weapon System Conversion Project.

•Completed Proposed Notice of Change Requests (PNOC) on the mechanical interface and facility coordination drawings to ensure weapon system integrity and adjudication of inputs from contractors.

•Developed interface requirements and inter-operable compatibility for mechanical coordination drawings. Performed configuration management (CM) tasks for equipment specifications.

•Completed engineering analysis on hydraulic system, cabling, temperature control, shock impact using geometric dimension and tolerance and principles.

•Participated in Naval Submarine Base Facility Technical Proficiency Evaluation (FTPE) assignments.

•Released parts list for processing acquisition/Logistics plan

Crown Consulting Inc., Washington, D.C. 03/2002 - 01/2004

System Engineer/Configuration Management

•Supported Federal Aviation Administration (FAA) Traffic Management Advisor (TMA) software project for Air En Route & Oceanic Services (ATO-E).

•Assisted in areas of system, software, adaptation requirements, and configuration management to FAA System Development Life Cycle Product Development Team.

•Generated and submitted the National Change Proposal (NCP) to the FAA CCB for approval.

•Completed Government Cost Estimation/Schedule, and submitted to the FAA CCB for approval.

•Supported FAA air traffic console modification project – Assisted to evaluate the console structure for the addition load on the console and provided the recommended structure enhancement and further to identify the stress concentration point and safety factor.

EDUCATION

•Lehigh University, Bethlehem, PA. M.S. Mechanical Engineering

•University of Arizona, Tucson, AZ. B.S. Mechanical Engineering

PUBLICATION

Experimental Mechanics volume 33-num 1: Digital Image Processing to predict uniform surface by using shadow moiré technique, FORTRAN software integration and IRIS instrumentation.

PROFESSIONAL LICENSES - TOOLS AND APPLICATIONS

•Cisco Certified CCNA ID: CSCO10637354, and Microsoft Certified MCSA 2000 ID: 2994466.

• AUTOCAD, SQL, Microsoft - Word, Excel, Visio, Project schedule.

Contact this candidate