Ironworker, welder, rigger
Resume:
ERIK CHEW
APT. ****
Saraland,Al 36571
********@****.***
________________________________________
OBJECTIVE: . I am confident that my 13 years of experience in construction will greatly assist in the lowering of incident rates and the safety of all employees.
CERTIFICATIONS:
• Nccer in ironwork • 10hr.OSHA 1910,1926
• PEC water safety
• Overhead Crane Certified Operator
• TWIC card • 10hr. MSHA
• 40hr. hazwoper
• 30hr. OSHA
RELATED SKILLS:
• 13 yr. experience in industrial trade
• Reliable and Dependable
• Honest and Ethical
• Able to Work Well as a Team and Independently
• Work well under pressure
EXPERIENCE:
C T E H June 2010 - September 2010
Industrial Hygienist/Safety Tech Deep Water Horizon
Determined employees’ exposure to environmental stresses. Developed corrective methods, controls, and procedures to improve work environment. Conducted industrial hygiene surveys of employees. Performed research studies of hazardous materials. Developed programs to ensure standardization of control and disposal procedures Performed specialized surveys involving outdoor air quality. Coordinated medical surveillance programs required to monitor the health status of employees. Conducted briefings on a variety of industrial hygiene and environment health programs. Prepared written technical reports with recommendations.Determined employees’ exposure to environmental stresses. Developed corrective methods, controls, and procedures to improve work environment. Conducted industrial hygiene surveys of employees. Performed research studies of hazardous materials. Developed programs to ensure standardization of control and disposal procedures
Titan Contracting & Leasing March 2009 – August 2009
Heavy Rigger Dry Fork Station
Signal or verbally direct workers engaged in hoisting and moving loads, in order to ensure safety of workers and materials. Test rigging to ensure safety and reliability. Attach loads to rigging to provide support or prepare them for moving, using hand and power tools. Select gear such as cables, pulleys, and winches, according to load weights and sizes, facilities, and work schedules. Control movement of heavy equipment through narrow openings or confined spaces, using chain falls, gin poles, gallows frames, and other equipment. Tilt, dip, and turn suspended loads to maneuver over, under, and/or around obstacles, using multi-point suspension techniques. Align, level, and anchor machinery. Fabricate, set up, and repair rigging, supporting structures, hoists, and pulling gear, using hand and power tools. Manipulate rigging lines, hoists, and pulling gear to move or support materials such as heavy equipment, or theatrical sets. Attach pulleys and blocks to fixed overhead structures such as beams, ceilings, and gin pole booms, using bolts and clamps.
Becon June 2008 –Febuary 2009
Heavy Rigger LG&E
Plan and execute heavy lifts on pipe and heavy machinery. Signal or verbally direct workers engaged in hoisting and moving loads, in order to ensure safety of workers and materials. Test rigging to ensure safety and reliability. Attach loads to rigging to provide support or prepare them for moving, using hand and power tools. Control movement of heavy equipment through narrow openings or confined spaces, using chain falls, gin poles, gallows frames, and other equipment. Tilt, dip, and turn suspended loads to maneuver over, under, and/or around obstacles, using multi-point suspension techniques. Align, level, and anchor machinery. Manipulate rigging lines, hoists, and pulling gear to move or support materials such as heavy equipment, or theatrical sets.
Sterling Boiler & Mechanical October 2007 – April 2008
Rigger/Fitter Warrick County Power Plant (Alcoa)
Position, align, fit, and weld parts to form complete units or subunits, following blueprints and layout specifications, and using jigs, welding torches, and hand tools. Verify conformance of work pieces to specifications, using squares, rulers, and measuring tapes. Lie out and examine pipe and tanks to be processed to ensure that specifications are met. Align and fit parts according to specifications, using jacks, turnbuckles, wedges, drift pins, pry bars, and hammers. Position or tighten braces, jacks, clamps, ropes, or bolt straps, or bolt parts in position for welding. Study engineering drawings and blueprints to determine materials requirements and task sequences.
Industrial Power Systems January 2007 – October 2007
Rigger/Welder Sun Oil Refinery
Planed and executed heavy lifts on tanks and heavy machinery. Position, align, fit, and weld parts to form complete units or subunits, following blueprints and layout specifications, and using jigs, welding torches, and hand tools. Verify conformance of work pieces to specifications, using squares, rulers, and measuring tapes. Lie out and examine pipe and tanks to be processed to ensure that specifications are met.
ISI March 2004 – December 2006
Ironworker/Welder SDI
Read specifications and blueprints to determine the locations, quantities, and sizes of materials required. Verify vertical and horizontal alignment of structural-steel members, using plumb bobs, laser equipment, transits, and/or levels. Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors. Hoist steel beams, girders, and columns into place, using cranes, or signal hoisting equipment operators to lift and position structural-steel members. Bolt aligned structural-steel members in position for permanent riveting, bolting, or welding into place. Fabricate metal parts such as steel frames, columns, beams, and girders, according to blueprints or instructions from supervisors. Pull, push, or pry structural-steel members into approximate positions for bolting into place. Cut, bend, and weld steel pieces, using metal shears, torches, and welding equipment. Fasten structural-steel members to hoist cables, using chains, cables, or rope.
Contact this candidate