Piping Designer Senior Design

Resume of Thomas E. Green Jr.

EMPLOYMENT HIGHLIGHTS

**/** – 02/25 AUSTAL USA – Mobile, AL

Senior Design Checker/Scheduler Utilized SSI ShipConstructor, Bluebeam Revu and Autodesk Navisworks software to check 3D models and 2D drawing products to ensure that they met contract specifications and Austal USA’s standards. Migrated into scheduling work for others to create 3D models 2D drawings, in addition to assigning checking assignments.

10/23 – 10/24 DOW SCO – Hahnville, LA

Senior Piping Designer attended Dow certified version 2019 Smart Plant SP3D Piping, Common, PCE and Structural courses. Utilized the SP3D software, Bently MicroStation V8, Bluebeam and laser scans to create 3D models, piping/equipment arrangements, isometrics, line list, tie-point lists for additions/retrofit to the existing Chemical Refinery. Field walk and verify prior to installation. Responsible for Olefins, Poly, Site Logistics and EXP area.

01/23 – 10/23 SNF Flopam – Plaquemine, LA

Senior Piping Designer Utilized the Aveva E3D piping and equipment software, AutoCAD Plant 3D, Bluebeam and laser scans to create 3D models, piping/equipment arrangements, isometrics, line list, tie-point lists for new construction fabrication additions/retrofit to the existing Chemical Refinery. Field walk performed laser scan prior to installation.

02/21 – 12/21 NASSCO a General Dynamics Company – San Diego, CA

Senior Design Engineer Utilized Aveva Marine 3D/2D, AutoCAD 2019 and Navisworks 2020 to create 3D models, and 2D piping/equipment arrangements for Engine Room, Auxiliary Machinery Spaces and various other compartments throughout the length of the Military Sealift vessel. Responsible for integrity of piping systems design.

03/20 – 10/20 FORD BACON & DAVIS (FBD) – New Orleans, LA

Checker/Senior Piping Designer Utilized AutoCAD Plant 3D 2019, AutoCAD 2019, Navisworks 2019 and LFM 4.3.0.18 to create 3D models, piping/equipment orthographic arrangements, isometrics, line list, tie-point list and specialty item list for

…Resume of Thomas E. Green Jr. continued…

installation, demo\fabrication additions/retrofit to the P66 Refinery (Belle Chase, LA.) and Formosa’s (St. James Parish, LA.) refinery projects. Responsible for NESHAP, Slurry, ULSD, Hydrogen, 175# Steam, HP Hydrogen and miscellaneous utility pipe system lines.

05/19 – 03/20 HUNTINGTON INGALLS INCORPORATED (HII) – Avondale, LA

Checker/Senior Piping Designer Utilized SSI AutoCAD ShipConstructor 3D and Navisworks to create and check 3D piping systems models on naval combatant ship LPD30.

04/17 – 05/19 NASSCO a General Dynamics Company – San Diego, CA

Senior Design Engineer Utilized Aveva Marine 3D and Navisworks to create 3D piping system models. Specializing in Engine Room, Auxiliary Machinery Space design and various other compartments throughout the length of the Military Sealift vessel. Responsible for integrity of piping systems design.

01/15 – 04/17 FORD BACON & DAVIS (FBD) – New Orleans, LA

Area Lead/Senior Piping Designer Utilized AutoCAD Plant 3D 2016, AutoCAD 2016, Navisworks 2016 and LFM 4.3.0.18 to create 3D models, piping/equipment orthographic arrangements, isometrics, line list, tie-point list and specialty item list for installation, demo\fabrication additions/retrofit for Shell Norco/Motiva (Norco, LA.) Logistics/HCU refinery project. Responsible for Outside Battery Limits, DU-5, RCCU, BFW, Hydrogen, 175# Steam, HP Hydrogen, Lean DEA, Hot Blowdown, Coker Gas Oil, Flushing Oil, LGO, VGO, Olefins, Water Draw and miscellaneous utility pipe system lines.

11/11 – 01/15 URS currently known as AECOM – New Orleans, LA

Area Lead/Senior Mechanical/Piping Designer lead designer utilized Bently AutoPlant XM, AutoCAD 2011, Navisworks 2011 and LFM 4.3.0.11 to create 3D mechanical/material moving equipment and piping models for Power Plant Dewatering Facilities and In-plant activities. Generated 2D deliverables for construction and visual aides consisting of piping/equipment orthographic arrangements, isometrics, line list, tie-point list and specialty item list for installation, demo\fabrication additions/retrofit for First Entergy (Shippingport, PA.) Coal powered Dewatering plant project. Responsible for new Dewatering Building piping, slurry

…Resume of Thomas E. Green Jr. continued…

piping, lime mixture piping lines in the pipe racks and incidental buildings and tanks, conveyor system from pit to barge landing in river.

06/07 – 11/11 NORTHRUP GRUMAN SHIP SYSTEMS – Avondale, LA

Senior Design Specialist Utilized CATIA V5 LCA/VPM to create 3D piping systems models on naval combatant ship DDG 1000 and Intergraph 3D (EMS) for Engine Room piping systems for LPD 17 naval combatant ship class.

01/07 – 06/07 SOUTH LOUISIANA ETHANOL PLANT (SLE) –

Belle Chase, LA

Lead Piping Designer Field Engineer overseeing construction and retrofit of SLE ethanol plant utilizing AutoCAD, FlexIso/FlexPipe to create sketches.

09/06 – 01/07 GIBBS & COX – Hampton, VA

Checker/Sr. Design Specialist Utilize SSI AutoCAD Shipconstructor 3D in conjunction with Naval Vessel Regulations to check, design, modify and revise piping routes in the Machinery Space for the 2nd Littoral Combatant Ship.

03/06 – 09/06 NORTHRUP GRUMAN SHIP SYSTEMS – Avondale, LA

Designer IV Field Engineering Utilized Intergraph 3D (EMS) and field walk checking to resolve distributive system issues between piping, mechanical and metal outfitting that prevented the fabrication and deliverance of LPD19, Naval combatant class ships in a timely manner interfacing with other disciplines.

12/05 – 03/06 LEEVAC – Jennings, LA

Senior Piping Designer Utilize AutoCAD 3D in conjunction with Coast Guard and Solas regulations to design all piping routes on the entire ship for a class of Offshore Suppl Vessels interfacing with other disciplines. Responsible for Mud suction/discharge, fuel oil, seawater, bilge ballast piping systems.

06/05 – 08/05 GIBBS & COX – Hampton, VA

Checker/Sr. Piping Designer Utilize SSI AutoCAD Shipconstructor 3D in conjunction with Naval Vessel Regulations and my experience to check and design piping routes in the Machinery spaces for the Littoral Combatant Ship class.

…Resume of Thomas E. Green Jr. continued…

04/02 – 01/05 NASSCO a General Dynamics Company – San Diego, CA

Senior Design Engineer/Lead/Supervisor I was the lead person responsible for the Pre-design NASSCO and Sub-contractor Design Team for the T-ake Contract. Utilizing Tribon M1, reference in accordance with customer specifications and requirements. I identified and initiated resolutions to problems that would impact NASSCO’s ability to perform to schedule prior to and during detail design. Established and maintained documentation and procedures to coordinate the interface responsibilities between the design groups within NASSCO and their outside Design sub-contractors. Represented Design Engineering at Production Workshops to capture their concerns and incorporate them into the design where feasible. Analyzed, recommended improvements/corrections to NASSCO standards, Material Schedules and Vendor Furnished Equipment (VFE) drawings to assist in the design development phase. This resulted in developing enhanced system diagrams that minimized the impacts to production by noting correct materials, and VFE interface connections. Supervisor for Phase I&II composite group, planning and scheduling of composite drawings for use by others while continuing to support the Design groups by identifying design deficiencies and ensuring that the correct production strategies were incorporated into the models prior to release to planning.

03/01 – 04/02 BOEING (Commercial Airline Group) – Everette, WA

Technical Designer Utilize and learned CATIA V4 3D, DCAC and PDM software while taking direction from engineering lead. Applied mechanical and design techniques acquired from a good understanding of aircraft structures and systems to create and revise detailed part, assembly and installation engineering drawing for various BOEING airplane programs (747, 757, 767 & 777).

11/98 – 03/01 AVONDALE SHIPYARD – Avondale, LA

Senior Design Engineer Utilized Intergraph 3D (EMS) to create 3D piping systems Engine Room and Auxiliary Engine Room models under the Integrated Product Team (IPT) concept for LPD 17 naval combatant ship class.

…Resume of Thomas E. Green Jr. continued…

06/90 – 11/98 NASSCO– San Diego, CA

Senior Design Engineer Lead designer utilizing Cadam 2D/3D and Calma software. I was the first person to be 3D trained on CADAM in NASSCO history. I represented NASSCO and shipbuilding within the United States while participating in the Integrated Product and Process Design process (IPPD) for the multi-discipline Integrated Product Team (IPT) concept for use by the shipbuilding industry. Traveled the United States and Japan while visiting other shipyards and various federal government agencies nationally. Served as Process Improvement Team (PIT) leader for internal cost and savings reduction within the shipyard. Graduated from the NASSCO Shipbuilding Technology Program (STP). Partnered in a patent for Modular Shipbuilding Construction. Responsible for various piping systems in the Engine Room, Auxiliary Engine Room and Pump Room for commercial container ship for MATSON Container Shipping Company, naval supply vessel AOE program. Worked in Advance programs performing estimates for future contracts. Scoped and processed naval change orders (HME/FME) for AOE program office.

06/84 – 05/90 BATH IRON WORKS (BIW) – Bath, ME

1-AA Designer Utilized Cad 3D software, AutoCAD, and pen and pencil to create and maintain 3D models and 2D composite drawings for FFG, CG and DDG naval combatant ships. I was onsite liason between BIW and it’s sub-contractors on the DDG program locally and in Virginia as well as a QA checker.

11/82 – 05/83 ADVANCED MARINE ENTERPRISE – Cherry Hill, NJ

Designer on the DDG Land-based test.

02/82 – 11/82 ELECTRIC BOAT (EB) – New London, CT

Designer verified weld identification inspection for 688 Class and Trident Submarines class.

11/80 – 02/82 CDI MARINE – Voorhees, NJ

Sr. Draftsman drew BCAD drawings for aircraft carrier overhauls for the Ship Life Extended Program (SLEP)

…Resume of Thomas E. Green Jr. continued…

08/74 – 09/76 J.J. HENRY Company – Moorestown, NJ

Accepted and joined their Marine Apprenticeship Program where I was taught in all aspects of Shipbuilding. I was instructed in the piping, electrical, ventilation and civil disciplines. We were taught how to read/develop drawing and diagrams in the various disciplines.

ACHIEVEMENTS

As a Sr. Design Engineer for Avondale Shipyard I was awarded an Individual award from the Government Program Manager and the Vice President of the program for recognition as a key team player as well as someone who demonstrated leadership skills to produce a good design while excelling in the challenge of learning a new CAD tool and the Intergraded Ship Design Process (ISDP)

While working for NASSCO shipbuilding I was the very first person to learn 3D design on CADAM that ushered in 3D modeling to NASSCO.

While working for NASSCO shipbuilding I worked as the piping representative on the team that received a patent for Modular Shipbuilding Construction.

While working for NASSCO shipbuilding I was nominated for and graduated from their Shipbuilding Technology Program.

While working for BIW I received a letter of recommendation from the Design director for the effort and work that I performed on the DDG 51 program.

Graduated from the Naval Apprenticeship Program at J.J. Henry.

I have demonstrated that I have the efficient ability, skill and knowledge sets to cross over to all industries, Naval, Aerospace and Petrochemical while designing various mechanical equipment components/systems and various piping systems from 1/8”ODT size pipe and up.

EDUCATION

Attended the University of Phoenix in San Diego pursuing a BA in business.

REFERENCES

Available upon requests.

Contact this candidate