Mechanical Supervisor Technician

CURRICULAM VITE

RAMALINGAM THILAGAR STUDIED DIPLOMA MECHANICAL ENGINEERING HAVING 10

YEARS OF VARIOUS WORK EXPERIENCE AS MECHANICAL SUPERVISOR(ROTATING) Mail id /Mobile Number: +919********* ***********@*****.*** Passport: V7096862 issued at Madurai validity till 27-01-2031 Employment details

Duration of Employment Name of Employer Position Held Jan 2024 to Sep 2024 PDO Oman (AIP Industries) Mechanical Supervisor Nov 2022 to Nov 2023 KIPIC – Kuwait (Gulf spic) Mechanical Supervisor March 2015 to August 2022 Qatar Gas (Madina group)-Qatar Mechanical Supervisor Jan 2014 to Feb 2015 Dolphin Energy &Qatar Gas

(Descon Eng) Qatar

Mechanical Technician

Aug 2011 to Nov 2012 Zamil Industry (Saudi Arabia) Mechanical Technician Apr 2007 to Sep 2010 Fenner India Limited - Madurai Mechanical Technician Aug 2004& June 2006 TNSTC - Madurai Mechanical Technician Roles & Responsibilities

Experienced in a variety of rotating equipment’s including single and multi-stage pumps, compressors, Fin fan coolers, Gear boxes etc.

Used different type of precision alignment methods including Rim and face, Reverse dial indicator.

Daily monitoring the sequence of activities performing at site and giving necessary instructions to maintain quality and also evaluate the daily progress of the job.

Witness initial alignment activities of equipment prior to base frame grouting and piping connection.

Witness pre and final alignment activities of pumps, Compressors, Gear Boxes and Fin Fan coolers in compliance of design and engineering practice of client specification and or vendors recommendation.

Find out root cause for different technical queries raised from site and give possible suggestion and solve the issues within pre-determined time period for smooth functioning of site activities

Receiving of equipment’s arrived on site and verification of documents (purchase order, release note, inspection release certificate, IFC drawing) and ensure for damage.

Monitoring preservation activities of equipment’s installed at site using preservatives as per vendor standards and procedures.

Verify readiness of foundation before installation of equipment’s (levelness, elevation, coordinates, and center lines of pad plate, anchor bolt projection and bolt dimension as per required IFC drawing).

Verifies the position and orientation of equipment during erection in accordance with costumer approved drawing issued for construction.

Witness preparation of grout form and grouting activities after preliminary alignment as per vendor recommendations.

Checking bolt torquing activity as per specification.

Sound knowledge in API 686 and other related international standards.

Daily monitoring of site activities and ensure work going on as per approved standards and procedures and giving necessary instruction to the team about the target requirements and quality objective of organization and client.

Maintaining better co-ordination with management, construction team and QC department for smooth functioning of site activities. Experience Details

I have acquired experience of both, the Field Maintenance as well as in Central Engineering Workshop carrying out different Maintenance Activities such as Overhauling and Repairing Variety of equipment’s. I’m conversation with various Safety Procedures Precautions taken while performing day-to-day Maintenance activities including different Permit Procedures. I am familiar with various maintenance activities such as Preventive, Predictive & Break down Maintenance Activities, carrying our Routine Inspection of Various Equipment’s as per schedule, Different Overhaul & Shutdown jobs, Installation & alignment of various rotating equipment’s. Attend the tool box meeting scope, and participated in fir fighting team as well, I have been trained safety to work with LNG plant and also trained H2S gas defending while working.

Conveyors & Rollers

Good experienced in conveyors running inspection & Breakdown activities. Belt vulcanizing joints. Pulleys replacement.

Plumber block (Bearing &Dust seal &Lip seal) replacement Wing robe (Counter weight) Inspection

Primary & Secondary scrapper replacement

Rollers (Metal &Rubber &Impact roller) running

inspection Stacker blade & Chain tension inspection Stacker chain guide roller (Bearing & Roller &Dust seal) replace Gear Boxes (Rotex & Flender)

Involved in different Gear box prevent maintenance & Overhauling at the gearbox (Replace Bearing &Oil Seals &Gaskets &Pinion) Check the Gear backlash.

Hydraulic (Braking System)

Ship Loader & Stacker (Hydraulic Braking system) Replace Oil Seal

& Gasket & Plunger &Brake pad.

Single & Double acting Hydraulic cylinder Replace oil seal& Dust seal Plunger rod (Pin hole& Rust &Trueness) inspection

Plunger ‘O' ring &packing seal replace

Alignment

Using rim and face method and reverse indicator solution by graphical method. Have good experienced with this both alignment method and confident to align. Have experienced in laser alignment as well. Steal rule aligning with Meta stem coupling. Soft hands with dial gauge and rot align. Motor axial float measuring and settings. Used pipe line flow discover by portable ultrasonic flow meter.

Centrifugal pump (Ebara &Flowserve & Friatec & Sundye & Nuovo pigeon) Experienced in assembling and dismantling of pumps (Sulfur Feed Pump), Sump Pump (vertical) Boiler feed water pumps, cooling water pumps, Crude and Vacuum Residue pumps,

Pump overhauling procedure Replacing Mechanical seal& Bearing &Oil seal. Impeller inspection (wear ring replacement) Check the Shaft run out & take the measurement of (Mechanical seal &Impeller& Bearing &Coupling) Centrifugal pump multistage(BB5) Sulzer &Flowserve & Nuovo pigeon Experienced in assembling & disassembling of multistage pumps Journal & Thrust bearing & Thrust collar & Mechanical seal & Balancing sleeve

&Drum & Rotor & Impeller replace.

Check the shaft & Mechanical seal centering

Check the journal & Thrust bearing clearance

Check the Balance Drum & Sleeve clearance

Check the Thrust axial clearance.

Vertical pump ( VS 6 & VBN Multistage) Gabbioneta

Experience in Assemble & Disassembling of vertical pump Bearing & Mechanical seal & Throat bush & Spider bush &Carbon bush & Shaft sleeve & Intermediate coupling & Impeller replace. Check the Throat bush & Shaft sleeve& Carbon bush clearance Check the Impeller clearance

Steam turbine( L.P& M.P) Siemens & Dresser rand

Experience have Assemble & Disassembling of steam turbine. Journal & Thrust bearing & Thrust collar& Carbon ring & Separation plate* Ejector plate & Nozzle & rotor replace.

Check the Rotor & Nozzle clearance.

Governor & Chest valve speed control adjustment.

Positive Displacement pump (PULSA SERIES 680)

Reciprocating pump (Piston & Plunger)

Change of piston & piston rings & replace bearing and cam shaft Diaphragm pump

Change diaphragm & stuffing box packing & Oil seal Replacement &Check valve inspection

Gear pump

Replace the Gear & Bearing

Replace the Oil seal

Valves Regulators:

Service and operation inspection o all types o valve like Ball valve, Globe valve, Plug valves, Gate valve, Globe valve, Butterfly valve, Diaphragm valve, Non return valve, Piston type NRV Automatic Pneumatic Actuators control valve in utility department. Various type of valves testing by seat test, body test, reverse test, Regulator dismantling and service.

Rigger certificate

7years Rigging activities experience have. Material shifting & loading Mechanical seal: Worked in john crane all type of seals including single and Double coil mechanical spring bellow, tandem seal, double mechanical seal and proper rectification of the same.

Centrifugal compressor (Split & Barrel) – MITSUBISHI (V 7 – 4) Thrust Bearing (Tilting pad) Replacement - 6pads

Journal Bearing Replacement – 5pads

Thrust Collar Replacement

Dry gas seal (Tandem seal) Replacement

Coupling Replacement

Turbo expander

MCS (Magnetic control system) Replace the seal & Bearings Expander follower seal Replacement

Inlet guide vanes Replacement

Expander Impeller & Compressor Impeller Replacement Fin Fans Blowers

Have experienced to measure and adjust blade angle, tip clearance. Belt adjusts tensioning in the pulley with Driver. Puller handling (manual and hydraulic). Replacement o blades. Greasing at the fin fan as well. Static Equipment pipe line

Worked in filters, strainers, flame arrester, pipe line free alignment, pipe line water flushing ad plant Maintenance. Involved in safety relief valves overhauling and Gate Valve, globe valve, ball valve, check valve, Ring type joint flange connections. Various type o gasket using in pipeline. Oil flushing to hydraulic line. Repair and change the glad packing and plant preventive maintenance o static equipments.

Diesel Engines

Having running maintenance experience in Weatherford, caterpillar and Hyundai engines. Involved I.C engine preventive maintenance and rectify startup problem. Engine oil refilling, radiator replacing and air lock removing. filter replacing as well. Engines cylinder inspection piston, piston rings inspection big and small end bearing inspection. Suction and discharge valve replacing and overhauling. Engine crankshaft overhauling.

Work Shop

Working in lathe thread cutting, shaping, Drilling, Grinding and taping bolts and grinding etc.

Contact this candidate